FORHOPE XM1000S pro Wireless Transmitter Receiver Kit Instruction Manual
- June 6, 2024
- FORHOPE
Table of Contents
FORHOPE XM1000S pro Wireless Transmitter Receiver Kit Instruction Manual
Installation Instruction
Foreword: Please refer to following installation diagram before using.
Product Diagram
Receiver:
- HDMI Output 1
- HDMI Output 2
- SDI Output
- 3.5mm Earphone Port
- Power On/Off
- USB Power Input/ Firmware Update
- DC Power Input
Transmitter:
- HDMI Loop-out
- HDMI Input
- SDI Input
- 3.5mm Earphone Port
- Power On/Off
- USB Power Input/ Firmware Update
- DC Power Input
Specifications and Parameters
UI Introduction
- 1.Startup Screen
The start-up screen is as above. When the device runs, it will display main menu.
- 2.Main menu
Main menu includes the following information’s. Channel, Device type(TX/RX), Link status, Signal strength, Video format, intercom mode, Battery level, Temperature, Fan status.
- Channel switch: Press ” ▲”or” ▼ “to change channels. Press “□ “to confirm the channel.
- Press and hold the “▲ “on transmitter, the screen will display device name and password. Press and hold the “▲ ” on receiver, the screen will also display device name and password if it’s connected to transmitter.
- 3.Secondary menu
Press and hold the ” □”for 2s to enter into secondary menu. Press and hold the “□ “for 2s again to back to main menu. Press”▲ “or ” ▲”to switch the options in secondary menu and press ” “to confirm selection.
-
Device(transmitter only): device type. Can switch between TX(transmitter) and RX(receiver) manually.
-
Source (transmitter only): Switch the sources between HDMI and SDI on transmitter. SDI input is selected by default if both HDMI and SDI sources are connected.
-
FAN Status: switch between ON and OFF to turn on or off the fan.
-
WPS: pairing. To pair transmitter and receiver.
-
Priority: to choose high image quality prior or low latency prior
-
WIFI_SSID: showing device name and password.
-
Version: showing the device’s version number.
-
Web: manufacturer’s web address
- Telephone: after-sales Tel number.
APP Operation Instruction
-
APP installation Search “” at Apple APP store or “For Hope” at Google Play Store to download and install APP.
-
Connect smart devices to transmitter After the transmitter is powered on, go to Settings-Wireless & networks on smart phone/tablet, select the transmitter’s name and input the password to connect the devices. Please find transmitter’s name and initial password as below. Then go to APP home page and click Video to monitor.
No need to input password again if it was saved on smart phone/tablet
Device nameXWMT_5G_xxxx
Password:12345678
-
APP Operation
b. Click VIDEO on home page to enter into monitoring mode. Click DISPLAY at the bottom of screen. It will show SCREEN CAPTURE, RECORD(only available for Android at present), MATERIAL, CONFIGURATION.
Press and hold the screen to show up the professional monitoring menu. P.S. Only monochrome, False Color and Center Mark are available at present. Other features are under development.
c. Click MATERIAL to check the images and videos saved on smart phone/tablet.
d. Click CONFIGURATION to access configuration screen.
e .Click the /Chinese Version at the bottom of home page
to change language.
Warning
- Cautions
■ Meaning of warning icons.
Caution, Notice, Warning, Dangerous, remind to be careful during operation..
■ Cautions
- Do not expose this device to extreme hot, cold, dusty or humid environments.
- Do not scratch the device with sharp objects.
- Do not drop this device from high place, as this may cause hardware damage.
- This device is designed for non-waterproofing. Please do not allow any liquid to penetrate into the device.
- Do not attempt to dismantle, open or repair this device by non-technical person, as this may cause permanent damage to the device.
http://weixin.qq.com/r/dEglPUXEhRj6rQFe9x1m
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment. Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>