MitarStar MIO-6706 Driver Board Development Kit User Guide
- June 6, 2024
- MitarStar
Table of Contents
MitarStar MIO-6706 Driver Board Development Kit User Guide
Chapter 1 Introduction
1.1 MIO-6706 Overview
The Wi-SUN (Wireless Smart Ubiquitous Network) Module Development Kit lets you try out the MIO-6706 Wi-SUN Module.
The MIO-6706 is a Wi-SUN Module designed to be integrated with IoT sensors and gateways for data transfer. The Wi-SUN network technology follows IEEE 802.15.4g/e and supports most available sub-GHz frequencies. The Wi-SUN solution provides the advantages of long range applications, low power, higher speed, hybrid mesh, and cost effectiveness. It provides open standards based secure, interoperable communications for large scale IoT, Smart Utility, and Smart City networks.
Chapter 2 The Development Kit
2.1 The Dimensions
The fixture board PCB size is 55 x 40 mm. The IO board PCB size is 75 x 70 mm.
2.2 Connecting the Boards and Powering Up
- Connect the fixture board and the IO board. Connect the included antenna to the IO board’s antenna connector.
- Connect the Micro-USB port of the Development Kit to the included Micro-USB adapter.
- Connect the adapter to a proper power source to power up the Development Kit.
2.3 Connecting to a Computer and Starting Up
Follow the steps below to connect the Development Kit to a computer and start it up.
- Power up the Development Kit by following the steps in Section 2.
- on page 4. 2 Connect the 4-pin UART port of the Development Kit to your computer’s USB port with an RS232 cable. Make sure the computer is powered on.
- You can access the Development Kit via various command tools in Linux and Windows environments. The following example uses Windows 10 and Tera Term.
- In Windows, open Device Manager and check for a new COM port. COM8 is used in this example
- Open Tera Term and click Setup > Serial port….
- Select the new COM port in the Port field.
- Set the baud rate in the Speed field to 115200. Click OK to save the settings.
- The following screen appears. You can now start using commands for the Development Kit. MIO-6706 Quick Start Guide
2.4 Other Information
2.5 Regulations/Certifications
Regulations (draft report only)
Chapter 3 Wi-SUN Module Specifications
3.1 Wi-SUN Module PCB Size
The Wi-SUN PCB size is 18 x 32 mm.
3.2 Specifications
3.3 Other Information
3.4 Power Tree
The IO board provides + 3.3V power to the system .
3.5 GPIO for Sub-1G TX/RX Switching
3.6 Regulation/Certifications
Regulations ( EVT Test only, no certificate)
Federal Communication Commission Interference Statement
This equipment has been tested and found t o com ply with the limits for a Class B digit al device, pursuant t o Part 15 of t he FCC Rules. These limit s are designed t o provide reasonable protection against harm flint reference in a resident installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance wit h the instructions, m ay cause harm fainter refence t o radio com medications. However, t here is no guarantee t hat interference will not occur in a particular installation. I f this equipment does cause harm full interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following m erasures:
- Reorient or relocate the receiving antenna.
- Increase t he separation bet ween t he equipment and receiver.
- Connect t he equipmentint o an out let on a circuit different from t hat t o which t he receiver is con n ect ed.
- Consult t he dealer or an experienced radio/ TV technician for help
FCC Caution: Any changes or m edificant ions not expressly approved by t he part y responsible for com pliancy could void t he user’s authority to operate this equipment .
This device com plies wit h Part 15 of t he FCC Rules. Operation is subj ect t o t he following t wo conditions: ( 1) This device m ay not cause harm full interference, and ( 2) t his device must accept any interference received, including interference that m ay cause undesired operation.
FCC Radiation Exposure Statement :
This equipment com plies wit h FCC radiation exposure limit s set fort h for an uncontrolled environment . This equipment should be installed and operated wit minim outdistance 20cm bet ween the radiator & your body.
IMPORTANT NOTE:
This m oduleisint ended for OEM integrator. This module is only FCC authorized
for t he specific rule parts listed on the grant, and that the host product
manufacturer is responsible for compliance to any other FCC rules t hat apply
t o t he host not covered by t he modular transmitter grant of certification.
The final host product still requires Part 15 Subpart B com pliancetesting wit
h t he modular transmitter installed.
Additional testing and certification m ay be necessary when multiple modules are used.
LABEL OF THE END PRODUCT:
The final end product must relabelled in a visible area wit h t he following ” Contains TX FCC I D: ZMY- MI O6706″ .
Antenna information
Documents / Resources
|
MitarStar MIO-6706 Driver Board Development
Kit
[pdf] User Guide
MIO6706, ZMY-MIO6706, ZMYMIO6706, MIO-6706, Driver Board Development Kit
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>