POINT MOBILE RF300 Authorized Distributor User Guide
- June 6, 2024
- POINT Mobile
Table of Contents
POINT MOBILE RF300 Authorized Distributor
Device Layout
- UHF Antenna
- LED Indicator
- Trigger-Mode key
- Connect-Mode Key
- Trigger
- USB Type-C Connector
- Battery Release Button
- Power key
Charging the RF300
The RF 300 and PM 30 are charged individually. Charge the RF 300 by inserting the USB Type-C cable to the connector. The RF 300 is fully charged when the charging LED is solid green (see next page for LED indicator).
Caution
- Always use an original power supply from Point Mobile. Other chargers and cables may damage the RF851.
- Make sure the connector, charger, cable is not wet.
- The device warranty does not cover any damage caused by the usage of non-original power supplies.
LED Indicator
Battery Replacement
Press PUSH button on the back of the handle to replace the battery.
When the battery cover is open, the battery can be easily taken out and replaced with a new one.
Package Contents and Accessories
Standard Accessories
Optional Accessories
Single Slot Cradle and Single Slot Ethernet Cradle
Specifications
| Item | Specifications |
|---|---|
| Frequency | UHF 900MHz |
| Protocol | ISO 18 3(18000 / EPC global Cass 1 Gen 2 |
| Output | Max. 30 dBm(lWatt) |
| USB | USB Type C / use to Ser1al Communication |
| Bluetooth | Bluetooth v4.0(aassic + Low Energy)/ SSP Profile |
| LED | LED(Charging /stare/ Connect-Mode/ Trtgger-Mode) |
| ButtDn | Power, Trigger Mode, C.Onnectlon Mode |
| Buzzer | Max, Min, Mute |
| C.Onfi gurations | RAD only or RFID with 2D scanner(Optional) |
| Size | 81.l(W) x 153.B(L)x 142.2(H) rm, |
| Battery | 3,250 mA, 3.6V Li-ioo (Replaceable) |
| Battery Charge Time | AC: About4H |
| Drop | I.SM |
| Adap!Dr | sv / 2A |
| Weight | 364g |
Certification
FCC Warning
FCC 15.105
This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC 15.21
Changes or modifications not expressly approved by the manufacturer (or party
responsible) for compliance could void the user’s authority to operate the
equipment.
IC Warning
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions :
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
For European Community Users
We have included this bulletin to comply with Directive 2012/19/EU OF THE
EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on Waste Electrical and
Electronic Equipment (WEEE)
This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, If not, properly disposed. In order to avoid the dissemination of those substances in our environment and diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal.
Those systems will reuse or recycle most of the materials of the product you
are disposing in a sound way.
The crossed out wheeled bin symbol inform you that the product should not be
disposed of along with municipal
waste and invites you to use the appropriate separate – take-back systems for
product disposal. If you need more information on the collection, reuse, and
recycling system, please contact your local or regional waste administration.
You can also contact your supplier for more information on the environmental
performances of this product.
CE Compliance (for EU only)C E:
This product is labeled with the CE mark in accordance with the provisions of
the applicable RoHS Directive 2011/65/EU for this product and the electric
accessories.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>