HuiCan Self-Balance Motorcycle Electric Remote Control User Manual

HuiCan Self-Balance Motorcycle Electric Remote Control

Specifications

Please read and follow all instructions and warnings in the manual prior to set up or use. Do not discard the manual.

Dear Customer：
We appreciate for choosing HuiCan radio controlled motorbike. For the safety reasons, please read the manual carefully. Keep the manual for future references.
Warning

1. This is not a toy. It is a sophisticated hobby product equipped with electronic and mechanical parts. It must be operated with caution and common sense. The operator should take all reasonable steps in order to protect: himself, other people or property. Not proper operations may cause injuries or damage property. We take no responsibility for any kind of accidents which are caused by incorrect installation of parts, usage or operations.
2. The product is suitable only for experience hobby grade hobbyists. The product is suitable for hobbyist who are over 8 years old.
3. We take no responsibility of operations, usage and etc after the product is sold.
4. Please, contact your local dealer for parts and repair consultations

Safety Precautions

It is high-risk product and we recommend always operate it away from people. The accidents may be caused by: incorrect motorbike’s parts installations; damaged motorbike parts; defective electronic equipment, unfamiliar operations of the motorbike. The driver should pay attention to the safety while driving the motorbike. The driver is responsible for the accidents.

Driving the Motorbike

1. Make sure the motorbike battery is charged and the transmitter battery is new.

2. Motorbike and transmitter on/off sequence: turn on the motorbike and then turn on the transmitter; after the drive, turn of the motorbike and after turn off the transmitter. Wrong sequence of this procedure may cause the motorbike be out of control causing injuries or damages.

3. Insure the battery is properly connected and it is not loose. Improper battery installment may lead to the signal loss.

4. Away from obstacles and people
   Pay attention to the speed and driving environment as these are the potential risk factors. Operate the product in open spaces away from: people, obstacles ,powerlines and high buildings. Pay attention to the weather conditions: strong wind, rain thunder are potential risk factors which may lead to a loss of control.

5. Away from damp environment
   The motorbike is build out of many electronic components. Therefore, keep away the aircraft from heat sources in order to avoid damages.

6. Safe usage of the product
   For safety reasons replace broken parts or upgrade existing parts only with original manufacturer’s provided parts. Obey the local laws and regulations when driving the product.

7. Beginners are not allowed to drive the product without the supervision.
   The motorbike driving requires specific skills and should be learned under direct supervision of an experienced adult. We recommend to use computer simulative software in order to get basic driving experience before taking the motorbike to the field.

8. Safety driving
   Do not drive the motorbike while under the influence of alcohol. Fatigue, poor spirit or not right operations will increase the probability or an accident.

9. Away from high speed rotating parts
   Keep away from high speed rotating parts. Rotating parts my cause bodily injuries, or damage the property.

10. Away from heat sources
    The motorbike is build out of: metal, fiber, plastic and electronic components. Therefore, keep away the from motorbike heat sources in order to avoid damages.

Transmitter

Choosing surface. We recommend to use indoors mode when driving indoors. Surface selection mode is off while driving in indoors mode. While driving in outdoors mode both surface mode selections are available. Please, choose rough ground mode if the surface is rough or has some sand particles.
Notice: wrong surface selection may cause the motorbike to fall down or behave unstable while driving.

Motorbike

1. Front/Back Lights: the lights will turn solid after the pairing is successful.
2. Back Lights: indicate gyroscope state and pairing procedure state.
3. Bottom Charging Indicator Light: when charging, the charging indicator light will be on; after the battery is fully charged the charging indicator light will go off.

Preparation for Drive

Installing the Transmitter Batteries

Turn on the motorbike

1. Place the motorbike on the ground (refer to the picture) and turn it on. The motorbike will emit double sound, after turn on the transmitter. To pair the unit move the right joystick fully up and after fully down. After successful pairing the motorbike’s back lights will turn solid.
2. As shown in the picture, hold the rider’s head and make the motorcycle vertical to the ground for 2-3 seconds. The motorcycle will maintain its balance automatically. After balance, the motorcycle can be controlled.
3. Place the motorbike on it’s side and the motorbike’s wheels will stop spinning.

Controlling the Motorcycie

Standard Mode
Push the left joystick forward and the motorbike will drive forward.

Push the left joystick backward and the motorbike will drive backward.

Push the left joystick left/right and the motorbike will turn left/right.

Back Wheel Mode
After successful pairing procedure place the motorbike on it’s back wheel and hold for 2-3 seconds. The motorbike will emit engine start-up sound and will automatically balance itself on the back wheel. Use the left joystick to drive forward/backward and the right joystick to turn left/right.

Stunt Mode
Drift: after the motorbike is set to the highest speed mode, drive it at full speed and press B button during the left/right turn. The motorbike will make smooth left/right drift.
Turn around: after the motorbike is in auto balance position, short press on the A button and the motorbike will make 180 degrees turn.
One wheel stunt: after the motorbike is in auto balance position, press B button and after 3 seconds the front of the motorbike will rise up making back wheel stunt. Use the left joystick to drive forward/backward and the left joystick to drive left/right.

Notice: these actions can not be taken on slippery, sandy or little friction ground. Before each drive ensure that the motorbike stays in auto balance position for 3-5 seconds.

Spin around: after the motorbike is in auto balance position, push the left joystick forward and the right joystick left/right. The motorbike will make clockwise or counter clockwise spins.

Charging the Motorbike Battery

The motorbike back flashing light and continuous warning signal indicates low battery voltage. Please, turn off the motorbike and recharge the battery.
Charging the Motorbike Battery Instructions:

1. Set the on/off switch to off position and off the USB charging port will be unblocked.
2. Connect the charging cable to the motorbike. Insert the charging cable into computer USB port or any other standard +5+0.5V USB charger.
3. When charging, the charging indicator light at the bottom of the motorbike will turn solid red. Unplug the charger when the light goes off. Charging time is about 130 minutes.
   For your safety do not leave battery charging operation unattended.

Dismounting the Rider from the Motorcycle

• If the rider doll falls off the motorbike, stuck it back on the motorbike. Ensure the dolls hands are attached to the steering wheel and groin attached to the sit.
• Do not drive the motorbike without the rider doll.

Routine Maintenance: the product is build out of high precision parts. Please, wipe off dirt and sundries from the rear wheel with dry cloth on regular basis.
Notice: if the product is not in use for a longer period of time, remember to turn off the motorbike and remove the battery from the product.

The content of the box

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>