Energy Management Collaborative EMCG001 Flanders Host Gateway User Guide
- June 6, 2024
- Energy Management Collaborative
Table of Contents
Energy Management Collaborative EMCG001 Flanders Host Gateway
Introduction
This installation guide provides basic instructions for Gateway Host.
Product Description
The Flanders Host includes Bluetooth 5.1 Mesh and 10/100 Ethernet (Cloud
Interface) Features.The 5.1Mesh is used for communicating with the Node
Product or BLE App.The Host supports standard IT network communications and is
easily integrated onto wired Ethernet networks for relaying data to and from
the host application. Architecturally attractive, the Host is easily surface
mounted on the table or hung on solid and hollow walls
Product Features
- Local Report Storage
- Cloud Interface for “Real-Time” report and database acquisition (AWS)
- iOS & Android App for commissioning
- Embedded Web UI for reporting and diagnostics
- Mesh Self-Healing Network
- 10/100 Ethernet (Cloud Interface)
- Bluetooth 5.1 Mesh
- Power Switch
- Reset Switch
- Restore Switch
- LCD Display
Hardware Features
BLE 5.1 Mesh (SiLabs BG21),Cortex ARM Processor (SAMD2),4GB Flash (NAND),Ethernet 10/100 µUSB 5V @ 1A,LCD Display,LED Status Indicator..
Circuit Board Terminal Blocks
Ethernet Interface (IP): The Host has a female RJ-45(8P8C) connector for
linking the device via Ethernet to the host application machine.
Reset Switch: The Host contains a reset button that when press ,the BLE
Mesh function will restart.And the BLE app will disconnected with the unit.
Restore Switch: The Host contains a restore button for reset the host
system when press the button and hold for a while until see the LCD display
indicated the “Reboot”,then the unit will auto-restart.
LCD Display : The Host contains a LCD display to show the Ethernet IP
address when the unit plug the CAT5 cable to con nect the Router and
computer.We can easier to get the IP address of the unit.
DC Power Input: The Host contains a DC terminal block for supporting
5VDC/500mA.
The Host contains a power switch for ON/OFF the power supply.
Circuit Board details
System Architecture
| Maximum Tx Power | RF 20dBm@2.402GHz-2.480GHz |
|---|---|
| RFSupported Modulation Format | GFSK |
| Ethernet | 10/100 Mbps |
| Power Source | 5V DC/500mA |
| LED Status Indicator | Alternate flashing RGB |
| Product ID | Unique factory-programmed ID |
| Construction | White ABS plastic |
| Dimensions (H x W x D) | 47×79.9×160.3mm |
| Weight | 205.2 grams |
| Power Source | 5V DC/500mA |
| Interfaces | Ethernet: Female RJ-45 (8P8C) connector |
| Operating Environment | Temp: -10°C to 60°C (14°F to 159°F) Humidity: 20% to |
80% non-condensing
Regulatory| FCC Compliant
Compatible Accessories
- ENTERNET SHILED CABLE L=1800mm OD:6.1mm
- SWITCHING ADP 100~240V 5VDC 0.5A XH-UL0505-A1+5V-0.5A
FCC Warning:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- ncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>