Shenzhen Century Xinyang Tech WD-RPT002 Device User Guide
- June 6, 2024
- Shenzhen Century Xinyang Tech
Table of Contents
Shenzhen Century Xinyang Tech
Shenzhen Century Xinyang Tech WD-RPT002 Device
SET UP VIA PHONE
Tips: Please make sure that the router is turned on and able to access the Internet before setting!
Step l
Please turn off cellular data at the beginning of the installation.Plug the
Extender into a power outlet near your Router.(Recommended within 20 feet)
Step2
Go to your Phone settings. Open WiFi, and turn it on. Search for the network
name “Hyzom-2.4G11 and click on it to connect.
Step3
Open the web browser and input 192.168.188.1
Step4
Once the page loads, enter the default password, “admin” into the password
box. Click the “Login” button to continue. If access fails, please check if
the correct SSID “Hyzom-2.4G” is connected or make sure it doesn’t capitalize
the “a” in admin – that won’t allow you in.
Step5
Enter the software management interface and click “Repeater Mode”.
Step6
Click on the name of the WiFi network you want to extend, e.g. My network. If
your home WiFi does not appear, please refresh it several times.
Step7
Type the WiFi password of your main router into the Password box. Click the
“Next” button.
Step8
After confirming the wireless information, click “Start Connect”
The new wifi SSID defaults to the “Router name-2.4G”. The password is the same
as your main router. Congratulations! The Wifi extender has been set up
.
CONNECT WITH WPS (IF SUPPORTED BY YOUR ROUTER)
Step1
Plug your wifi extender into an outlet near your router, then wait for the
wireless LED to turn on and stay solid. (Recommended within 20 feet)
Step2
Press the WPS button on your main router for 1-2 seconds
Step3
Within 30 seconds press the WPS button on the Extender for 1-2 seconds.
Step4
After 30 seconds, a network will appear. The new WiFi SSID defaults to the
“Router name-2.4G”. The network will have the same password as your current
network.
Step5
Move the Extender to the best position which is halfway between your router
and the area that has poor WiFi signal. Congratulations! The WiFi extender has
been set up and you can go online.
HOW TO RESET THE REPEATER
Please press the RESET button on the left side of the WiFi extender for 8
seconds to restore the factory settings. , (The WiFi extender needs to be
plugged in to reset]
OTHER MODES
Bridge Mode setting: The setting method of bridge mode is the same as the
repeater mode. Please refer to the setting method of repeater mode. This mode
is suitable for printers, IP cameras, smart TVs, etc.
Client Mode setting: The setting method of client mode is the same as the
repeater mode. Please refer to the setting method of repeater mode. After the
setting is successful, use the network cable to connect the extender with the
wired equipment, and the wired equipment can access the Internet.
AP Mode setting: In order to facilitate the management, this IP address
and default gateway entered here should be the IP segment of the superior
router, and the IP address cannot be the same as the superior, avoid IP
conflict with the router. After the setting is completed, the WAN port of the
device can access the external network through the set IP address Network to
access the management device.
Router Mode settings : Enter the software management page, click Router
Mode, which can select ” PPPoE”, “StaticlP”, “Dynamic IP” Three ways to get
online.
- PPPOE dial-up mode: This mode requires the Internet account provided by the network service provider to be flied in Number and password, below can set 2.4G wireless SSID name, wireless password.
- Static IP mode: This mode needs to fill in the IP address provided by the network service provider, Subnet mask, gateway, main DNS address, 2.4G wireless SSID can be set belowName, wireless password.
- Dynamic IP mode: In this mode, the WAN port is assigned IP by the superior network device to access the Internet. The 2.4G wireless SSID name can be set below.
Troubleshooting
My WiFi says connected but I have no internet connection.
- 1f the WiFi is connected, but there is no internet, check that the router’s WiFi is actively working. And try to restart the router.
- it might be more of an IP conflict. You can try to set it up in Bridge mode so that the devices connected to both routers can interact with each other.
- you may have entered the wrong password. It could also be for some other reasons, so try to restore factory settings. To do that, please press the RESET button for 8 seconds to restore the factory settings, then set up the extender again.
Why does the internet speed drop when connecting to the extender?
- The WiFi Extender supports 2.4G networks and not 5G.
- The WiFi Extender is used to extend the range of your wifi (which your main router wifi can’t cover). It does not increase internet speed.
- Sometimes, the signal (coverage or speed) drops due to external influences- – a microwave oven, nearby cell towers nearby, a neighbor’s WiFi on the same channel, walls, and partitions in a building made of certain materials blocking a WiFi signal.
- Try the Extender in different positions: place it at different angles or locations for a better signal.
What is the user name and password for setting up the Extender?
- The user name and password for used during setup is admin
- After setting up, connect to the new WiFi name “Router name-2.4G11 The password is now the same as your WiFi main router.
Why are some devices at home (printer, CCTV camera,TV, iPhone) unable to connect to the Extender?
- This means the device does not recognize the Extender.
- The device should be in the same network as your router. You may set up the Extender in Bridge Mode to see if it will work.
Why am I unable to enter the web page?
If you cannot open the webpage, follow these steps:
- open your browser on your cellphone/PC, and enter the digits “192.168.188.1” into the address bar. Enter the user name and password “admin” then log in. You can also connect the WiFi extender to your PC with an Ethernet cable, then open your browser and enter the same digits “192.168.188.1”. Enter the user name and password “admin” and follow same steps.
If you are still unable to open the webpage, please check and try these:
- check if you are connected to the WiFi extender during setup. This is necessary because before connecting to the router, the WiFi Extender should have no internet access. Your mobile will usually auto-connect to the otherWiFi or ask if it is connected to the present WiFi or not. You must be connected to the WiFi Extender during setup.
- Please press the RESET button for 8 seconds to restore the factory settings. Set up the extender again.
- Disable your mobile’s data during setup.
- Use another mobile phone to try.
WARNING
- Keep the device away from water, fire, humidity, or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- Do not use the device where wireless devices are not allowed.
- The socket outlet shall be installed near the equipment and shall be easily accessible.
- For passthrough devices, plug the power strips into the integrated electrical sockets of the devices, but devices of the same or another type not be stacked in normal use. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device, please use this product with care and operate at your own risk.
HYZOM GUARANTEE
IMPORTANT: All Wifi extenders on the market are designed to increase or
improve WiFi coverage. That means It can improve the locations which are
getting weak signals from your router and NOT TO INCREASE WIFI SPEED According
to the laws of physics, WiFi Extenders will always be slower than your
existing router. This is because the WiFi extender has to split its bandwidth
between the router.
Note! Based on 300 000+ sold units, the extender may not be effective or
doesn’ t work in 3% of cases due to interference or incorrect setup.
ONE OF THEM? Contact our friendly customer service team:
support@hyzomoffice.com
UNHAPPY? We’ll give a full money refund or a replacement and you can keep
the old product to avoid to hassle of shipping the product back.
“Wo unto the liar, for he shall be thrust down to hell.”
“Good thing we ain’t lying.”
Scan the QR code with the camera to watch how to setup the WiFi Extender
If you have any questions, please CONTACT US
support@hyzomoffice.com
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. The
antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>