Guilin Gemred Sensor Technology 84103 Digital Body Tape Measure Instruction Manual
- June 6, 2024
- Guilin Gemred Sensor Technology
Table of Contents
Guilin Gemred Sensor Technology 84103 Digital Body
Tape Measure
Smart Body Tape Measure
TECHNICAL DATA
Unit| cm/in
Accuracy| 2%.
Resolution| 1mm
Measuring Range| 1500mm
Working Temperature| -o·c -so·c (32°F-122·F)
Working Humidity| S85%
Battery| CR2032
BUTTON
- Short press: confirm the measurement and send it to the APP via Bluetooth
- Short press: power on/off
- Short press: switch between inches and centimeters
INSTALL THE BATTERY
Press and rotate the battery door anticlockwise. Battery
door will be open. Insert the battery. Make sure the
positive pole face up
Close the battery door clockwise.
HOW TO USE
TROUBLE SHOOTING
Problem
|
Possible Cause
|
Solution
---|---|---
No display or ambiguous
|
Lower voltage, no battery, or incorrect installation of battery
|
Reinstall battery or replace battery
Erratic display
|
Casual misfunction caused by high vibration or strongly swinging
|
Zero setting
Number skip or frozen display
|
internal error
|
Remove battery wait 1 minute and replace
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician f
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules and Industry Canada
licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC & IC Radiation Exposure Statement:
This equipment complies with FCC and Canada radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>