Ningbo Biumart E Commerce BM-SC001 Wireless Security Camera User Guide
- June 6, 2024
- Ningbo Biumart E Commerce
Table of Contents
Low-Power WIFI Battery Device Quick Stan Guideline
Technical Parameters
Resolution:720X1280 I I 1920X1080
Video bitrate: adaptive
Viewing angle:135-165°
Storage: Micro SD Card
Support capacity: Up to 128G
Audio: Built-in speaker& Microphone
Recording method: Memory Card / Cloud Storage
WiFi mode : 2.4GHz 802.11n / g / n
power supply: DC 5V Power consumption: Standby 200uA, Working 200mA
Battery capacity: 6000mAh Motion
Detection: PIR Sensor
1. APP Download
- The APP used by this device is “One cam”, it can be downloaded by scanning the QR code below or searching “One cam” to download the APP through the Android or ios platform application store.
- [Note]: To ensure that the mobile phone can receive the information pushed by the camera, please allow all notification permissions of the APP when installing the camera APP “One cam”.
- Please use your mobile phone to register an account before logging in to the APP
Product Appearance
Indicator Status Description
[ Note ]: If you need to configure the network or connect with the AP, you
need to make sure that the network indicator is steady red.
Make sure that the device is waiting for network configurationWaiting for
network configuration| The network indicator is steady red
---|---
Device sleep| The network indicator is off (not lighting)
Device offline| The Network indicator flashes red
Device charging| The charging indicator is steady red
Charging completed| The charging indicator is steady blue
Preparation Before Distribution
- The camera only supports the 2.4G Hz 802.11b / g / n standard wireless WiFi network. If you are a dual-band router, please use the 2.4G network to connect the camera. And it does not support the optical cat integrated router with firewall function and the open WiFi network of the mall for the moment.
- Set the power switch of the camera to ON, and wait for the red indicator light on the panel to stay on, then you have entered the WiFi networking state.
[Note]: If the camera network indicator is not steady red, please long press the reset button until the red light is steady on, then release the button to reset the camera network.
2. Add Device
- Log in b the APP, click the “+” in the device list, and pop up a window to choose”Add intelligently”.
TF Card Video
Click the “File” icon to view the video in the TF card (Note: The device needs to be plugged in the TF card, the alarm detection is enabled and the video is recorded before the video file can be found).
Cloud Storage Video
Click the cloud storage function icon in the device list page, Enter the cloud storage video query and open the purchase page. Device Sharing
Click the “Share” icon to enter the “Shared Management”, click the “Share ” button, your family can dick the “+” APP to select “Scan” to share the device code, you can view your shared device. AP Hotspot Mode
Reset the device, open the APP, click “Add Device” and select “AP Mode” to enter the hotspot connection interface. Click “Next” to enter the mobile phone WIFI selection page, find the WIFI hotspot named “One cam-xxxxx” to connect, (WIFi password: 123456789).
Installation
-
The product supports placement or wall-mounted use. The wall mount installation requires the use of a base bracket. and the installation height is recommended not to exceed 3 meters (As shown in below picture)
-
PIR sensor has a certain direction, adjust the camera angle up and down. and adjust the vertical sensor range. Adjusting the camera angle horizontally changes the lateral sensoring range.
-
If you need to punch holes for wall-mounted installation, please use the No. 6 impact drill to punch holes.
-
If you use 3M double-sided adhesive to paste the wall-mounted installation. please first fix the base bracket to the location where you need to install it, and then apply a circle of transparent glass glue around the base bracket Wait one day until the glass glue has completely solidified before screwing the device on the base bracket.
FAQ
Q: What should I pay attention to before using the product?
A: When the product is paired, ensure that the distance is within 2 meters of
the WiFi signal coverage of the router to add network operations. It is
recommended to install the device within 10 meters of the router.
Q: Why are there issues with push delay and wake-up delay?
Al: The product transmits data through a wireless network, and it takes 0-1s
to convert and output the data when processing the data, so there will be a
0-1s delay when the product is used. Please use it normally about 5 seconds
after the product is successfully connected (operate after the connection is
stable).
A2: If the wifi signal is weak or the mobile phone signal is weak, it may also
cause offline and disconnection, and push notification delays. Before buying,
check the will coverage area to ensure sufficient signal to avoid a bad
experience.
Q: Why can’t the phone receive the alert notification?
Before using this product, please enable the “Automatic management’ function
of the “One cam” APP, and enable all the permissions and notification
functions of the APP.
Q: The device is online and the APP cannot receive push messages?
Al: The mobile phone turns on ‘automatic management” for the “One can” APP,
and turns on all the permissions and notification functions of the APP A2: If
you turn off the [Allow Notification] of the APP in the [Notification and
Status Bar] of Huawei/Xiaomi mobile phones, there will be no reminder in the
notification bar,
Q: Regarding PIR (Human Body Thermal Infrared Sensor) is not sensitive or
the sensing distance is long and short
Al Allis device is a low-power smart product that wakes up work, video and
pushes information through PIR A2:As the PIR (Human Body Thermal Infrared
Sensor) is easily affected by the external environment, such as heat source or
light source: therefore, the installation and use a position of the equipment
should be avoided as far as possible from the air outlet of the air
conditioner, the place with a heat source or direct sunlight
Q: What should I do if I cannot receive the verification code during email
registration?
Al: Please make sure your email account is entered correctly A2:Some mail
clients will recognize the verification code as spam, please go to the spam
inbox to check whether there is a verification code email
Q: How to operate Apple and Android phones?
Al:iOS operation steps: enter the phone settings, drag the screen to the
bottom. find the APP, see the microphone permission, set to open; A2:Android
operation steps: enter the phone settings, open the application management.
find the APP, open the permission management. see the microphone (recording)
permission, set it to on
Q: What does the color of the indicator light represent?
Al Mork indicator light(UP): the device is working normally and the indicator
light is flashing blue (flashing once per second) A2: Work indicator light:
the device is offline (the device is disconnected from the router or the
router is out of network), the red light flashes (flashing once per second)
A3:Power Indicator(Middle): when charging by USB steady red: charging fully
steady blue. A4:Reset After the device presses the reset button for 3 seconds,
the device work indicator tums to a steady red light A51 the device does not
receive the configuration during the network configuration process or the
network connection is unsuccessful, it will remain on the work indicator light
is always red on. Atif the network is normal, the Work indicator light can
automatically return to normal work. The indicator light flashes blue.
FCC Statement This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the aim its
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference WI n of occur
in a particular installation. If this equipment does cause harmful
interference t o radio or television reception, which can be determined by
turning the equipment off and on, the user i s encouraged to try to correct
the interference by one or more of the following measures: – Reorient or
relocate the receiving antenna. – Reorient or relocate the receiving antenna.
– Reorient or relocate the receiving antenna. – Consult the dealer or an
experienced radio/ TV technician for help important announcement Important
Note:
Radiation Exposure Statement This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment This equipment
should be installed and operated with a minimum distance 20cm between the
radiator and your body. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>