Veri SHADES DT980LE Curtain Motor User Guide

Veri SHADES DT980LE Curtain Motor

Product introduction

Functional features：

• Electronic Limit
• Switch Direction
• Auto Limit Setting
• Run/Stop by Pulling Fabric
• Preferred Stop Position
• Lithium Battery with Quick Plug
• Stall Protection
• Built-in Receiver
• Manual Override
• Switch Control
• Program Button
• Solar Charging

Parameter (More models and parameters are subject to the nameplate)

Type| Rated Torque (N.m)| Rated speed (RPM)| Rated Voltage (V)| Emission Frequency(MHz)
---|---|---|---|---
DT980LE/S| 1.2N.m| 80-120RPM| DC 14.8V| 433MHz

Motor installation

1. The joint assembly of track
2. The assembly of rubber belt for curtain motor
3. Folding method for the joint track (for easy transit)
4. The installation method for curtain motor

Operation note

Please read the following precautions before use:

1. Not operating under low voltage motors:
   Motor stop running when the supply voltage is lower than 13.5V, LED light will flash 5 times, buzzer beep 5 times, prompt low voltage to be charged

2. Operating：

3. The valid interval of the emitter button is 10s, the emitter will quit the set after 10s;

4. The LED flashes or beeps for the hint, please do the next step after the hint.

5. Set limit position：

6. Every time you install the motor, first set after a curtain opened travel to work properly;

7. After setting, with power and memory function, after each power cycle required to open or close a recovery stroke;

8. After replacing the track or cord to be removed for the trip, and then set the itinerary.

9. When the motor runs without any operation, the maximum running time is 4 minutes,it will stop automatically.

10. One motor maximum can store 10 channels, over 10 channels,if still need to add new channels, it will be repeating covered in turn from the second channel.

11. If the emitter is lost, please set it up again with the new emitter.

Button specification

Factory mode

1. Setting up

2. Switch direction

3. Speed regulation
   Note: If the motor is short sound twice, it means the speed is already fast or slow; when there is no limit, the motor defaults to low speed running. When there is limit, the motor will run fast by default.

4. Limit position setting

User mode

1. Preferred stop position
2. Fine-tuning open/close limit position
3. Add/delete emitter
4. Weak electric switch mode selection
5. Run/stop by pulling fabric
6. The search function
7. Reset to factory mode

Fault and solution

NUMBER

|

COMMON FAULTS

|

PROCESSING METHOD

---|---|---

1

| The motor is not running|

Check the power supply

2

| Unable to control remote controller|

1, Check the emitter for the code;2, Replace the emitter battery

3

| Remote control on the contrary|

Implement the reverse of direction setting

4

| External switch is out of control|

Check the external switch motor cable is intact

5

| External switch on the contrary|

Replacement switches line order

6

|

Cannot close

| 1, Check emitter’s open button to ensure if it works with open function, if not,please change direction firstly;2, check limit position;

7

| Always hit or couldn not get to the edge|

Cancel the limit,setting again

8

| With the hand to pull,feeling stuck|

Set the limit of the trip

9

| Encounter obstacles will not stop|

Check the screw used to fixed orbital

SAFETY NOTE

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by children without supervision.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
5. WARNING: the drive shall be disconnected from its power source during cleaning, maintenance and when replacing parts.
6. The instructions shall state that the A-weighted emis sion sound pressure level of the drive is equal to or less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).
7. The mass and the dimension of the driven part shall be compatible with the rated torque and rated operating time.
8. The type of driven part the drive is intended for.
9. WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions.
10. Do not allow children to play with fixed controls. Keep remote controls away from children
11. Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary
12. Watch the moving shutter and keep people away until he shutter is completely closed
13. WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
14. Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>