UNiKA EQ-815 Professional Sound Equipment User Manual

UNiKA EQ-815 Professional Sound Equipment

EQ-815

INTRODUCTION

We congratulate you on choosing a Sound Product equalizer. You will find that it has been designed for easy use. The latest advances in audio technology have been utilized in the design of making thisequalizer the ideal brain of any audio system. We have incorporated many features to help you, including 15×2 band of tone effects controls, in/out passing switch, low-cut switch control and level control. Whether you’re looking to custom tailor that mix or optimize the acoustics of a really tough room. Please read all instructions carefully before operating.

WARNINGS

1.  All operating instructions should be read before using this equipment.
2.  To prevent the risk of electrical shock, do not remove cover or back, no user-serviceable parts inside,refer servicing to a qualified service technician.
3.  Do not expose to direct sunlight or heat source, such as radiators, stoves, or other appliances that produce heat.
4.  This unit should be cleaned only with a damp cloth, audio solvents or other cleaning detergents.
5.  When moving this equipment it should be placed in its original carton and packing. This will reduce the risk of damage in transit.

INSTRUCTIONS FOR CONNECTIONS

1.  Be sure that the power (1) is in the off position. All connections must be made with the equipment off.

2.  Before plugging in the power cord (8) make sure the voltage selector switch (7) is set to the correct voltage.
   (The unit is preset to 110 volts). Insert the power cord into the proper source.

3.  For best sound use only high quality audio cables when hooking up this equalizer. Make sure that all cables are pushed in securely.

4.  Make sure you correctly attach the patch cables for the input source and output signal.

OPERATING INSTRUCTIONS

1.  Power On: Once you have made all connections to your equalizer, Press the Power (1) button. The equalizer is on. Press again to turn the power off.
2.  IN/OUT Passing Switch (2): Press this switch in, the equalizer will be activated. Press it again to out, the signal will be passed.
3.  Graphic Equalizer (3): These sliders allow adjustment up to 12dB each octaves 25Hz to 16KHz (Dual 15 Band). These equalizer controls are provided for improving frequency response of your system, compensating for room environment effect.
4.  Level adjustment control (6): You can obtain a proper output signal level using this level control. The Level Display LEDS (4): will indicate you the exact output levels from -10dB to +18dB in 4 steps. When the + 18dB LED lights up, it tell you that there is too much outputpower calibrated to produced distortion, lower the level control gradually until this LED goes off.
5.  Low Cut Switch (5): The low-cut switch attenuates the muddy and unwanted sound created by your source equipment, especially from record players.

EQ-815

•  Dual 15 band, 2/3 Octave from 20Hz ~ 20KHz
•  ±12dB input gain range
•  EQ band control level range of ±12dB
•  45mm slide controls 20Hz ~20KHz frequency response, +/-1dB
•  Low cut filter 60Hz – 3dB
•  XLR, TRS balance input
•  XLR, TRS balance output
• Signal level at -10dB, 0dB, +10dB, +18dB LEDs indicators
•  Low cut, & bypass function w/LEDs indicators
•  Operating voltage is switchtable: 110V-120V/60Hz; 220V-240V/50Hz
•  2U rack space

Front Panel and Rear Panel

EQ-815

1.  Power Switch
2.  In/Out Passing Switch
3.  Fader Frequency setting
4.  Level Display LED Indicator
5.  Low Cut Switch
6.  Input Gain Level Control
7.  Voltage Selector Switch
8.  Power Inlet
9.  Input Jack
10.  Output Jack

References

• Unika Electronic Co., Ltd

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>