Atlantic CCPL1 – 74094 Color Changing Single Pond Light Kit User Manual

Atlantic CCPL1 – 74094 Color Changing Single Pond Light Kit

Introduction

Thank you for purchasing Atlantic Color Changing Pond Lights. Atlantic’s Pond Lights feature high impact cases and silicone gaskets for dependability and longevity. Whether underwater or in open air applications, Pond Lights impart a soothing, warming glow after the sun goes down. Available in single light or triple light kits with included removable photo cell and transformer.

Prior to Operation and Installation Caution:

•  DO NOT operate this product under any conditions other than those for which it is specified. Failure to observe these precautions can lead to electrical shock, product failure, or other problems.
•  Follow all electrical codes when installing Atlantic Lighting.
•  To reduce the risk of electrical shock, connect transformer to a 120 volt receptacle protected by a ground fault circuit interrupter (GFCI).
•  Always verify that the lens is tightly secured before submersing the fixture
•  Quick-connect plugs are gasketed for outdoor use and must be fully tightened to prevent water infiltration. Quick-connect plugs are not waterproof and should not be submersed.
•  Always use dielectric grease on all connections and verify that the lens ring is tightly secured before submersing the fixture.
•  Never shorten or cut the cord on Atlantic Color Changing Lights. Cutting/shortening the cord will damage the LED and void the warranty.
•  The InfiColor Smart Module is weatherproof, but must be mounted above the ground on a wall or post within reach of a properly grounded GFCI outlet. Do not submerse the Control Module or expose it to heavy rainfall. Failure to do so will void the warranty.
•  The InfiColor Smart Module can be connected to an existing 12 volt AC lighting system by cutting and splicing the flat low voltage wire that supplies power to the Module.

Installation

Pond Lights offer two different mounting options for your convenience:

•  Adjustable stand: for placement on rock ledges, under waterfalls or for highlighting streambeds
•  Nestled: without the stand amongst the pond stones

Proper light placement is important for every project. Whenever possible, lights should be positioned facing away from the viewing area to minimize hot spots. When camouflaging the light cord with rocks and gravel, always leave enough slack in the cord so that the fixture can be raised above water level for servicing

Color Changing Pond Lights

The Single Zone InfiColor Smart Module is weatherproof, but must be mounted above the ground on a wall or post within reach of a properly grounded GFCI outlet. Do not submerse the Control Module or expose it to heavy rainfall.

•  Install the Smart Module in a well-ventilated area to ensure that the Module operates within its specified working temperature.
•  Verify that the Smart Module input voltage is 12 volt AC. We recommend that you use the transformer provided with this unit.
•  Use dielectric grease on all connections and ensure that all cable connections are secure.
•  Do not connect the power before the cord connections are finished.
•  Do not cut or alter any round cords. Cutting or damaging any round cord will void the warranty.

Connecting Lighting To Module

Apply dielectric grease to the pins of the plugs on the InfiColor Smart Module and light cords. Line up the keys; the plugs will only fit one way. Connect the plugs and tighten the threaded ring. Complete the tightening process by wiggling the connection and retightening the threaded ring 2-3 times until firmly seated.

INFICOLOR MOBILE APP

To connect your mobile device to the Smart Module, be sure the Module is plugged in and open the InfiColor App. The app should populate your Smart Module on the opening screen. Simply select the Module name. Please note the Module can be connected to one mobile device at a time. The Single Zone Module will only modify the settings of Zone 1 on the app.

To Configure Zone Name and Timer

Click dropdown menu. Edit the name of the zone on the “Zone Settings” page. This zone name will be visible throughout the app. The zone has a timer function to turn the zone on and off at set times. Click the “Save” button to save changes. A box will come up confirming the settings have been saved. Click the “Back” button once configuration is complete.

Color Tab

Use the Color tab to choose colors using either the color picker or the red, green and blue sliders at the bottom. Choose the brightness of the color by adjusting the slider.

Favorites Tab

The Favorites tab stores preset color changing sequences. Choose a sequence of colors, then choose the transition between them, the speed of the sequence and the brightness. The Edit button deletes stored Favorites.

Custom tab

The Custom tab creates and stores a custom color changing sequence. Move the red, green and blue sliders to choose a color, or select it from the color picker. Click the “Plus” button to add it to the sequence. Repeat as desired. Add up to 10 colors to a sequence. Once the sequence has been created it can be named and saved. The saved sequence will be available on the Favorites page.

Maintenance

Replacement LED diode assemblies are available for Pond Lights. Loosen clear plastic lens and remove diode assembly. Install new LED diode assembly and align gasket. Tighten clear plastic lens. Ensure that all components are installed correctly after servicing. Ensure that the clear plastic lens is tightly secured before submersing the fixture.

Winterization

Pond Lights may not be left where water freezes solid. If lights are installed in shallow streambed waters or close to the surface, they should be removed from the pond for the winter or relocated to deeper areas that do not freeze.

Warranty

All Atlantic Pond Lights carries a one-year limited warranty..All Atlantic Wiring Components carry a one-year limited warranty. This limited warranty is extended solely to the original purchaser commencing from the date on the original purchase receipt and is void if any of the following apply:

•  The light body/LED components have been misused or abused.
•  The light body/LED components have been disassembled or modified other than as described in this manual.
•  The light has been damaged by freezing water
•  Any round cord has been cut or altered.
•  The Smart Module and quick-connect plugs have not been adequately protected from moisture with dielectric grease.

This warranty excludes labor/cost of labor for removal or installation of any product.

Warranty Claims

In case of warranty claims, the complete product should be returned to the place of purchase accompanied by original receipt.

Troubleshooting Guide

Always turn off power before inspecting the lights. Failure to observe this precaution can result in a serious accident. Before ordering repairs, carefully read through this instruction booklet. If the problem persists, contact your dealer.

Lights will not turn on

| No input power to the transformer|

Verify power to the outlet is on / Check GFCI reset

No outlet power from the transformer|

Test with multi-tester

Photocell malfunction

| Cover the photocell with a piece of dark tape to check function

Unplug photocell and plug light directly into transformer

Lights will not turn off|

Photo cell is covered

| Clean sensor and outer clear covering

Make sure nothing is shading the sensor

LED color differs from app

| Improper connection between LED light and Smart Module|

Inspect connections / realign plugs

Smart Module failure| Contact Dealer for repair / replacement

Individual lights within a larger system not working

| Improper connection to Smart Module| Verify connections are aligned
Loose connection Moisture or corrosion in connections| Inspect quick-connected plugs for moisture, corrosion or missing gasket.

Clean/ dry and reassemble.

Failed LED diode

| If possible, switch out the LED diode assembly with one from a working light of the same model to determine if the driver has failed.

If driver has failed, replace light.

If test diode works, replacement LED diode assemblies are available.

Smart Module is not responding to app| App is not synced with Smart Module|

Reconnect Smart Module through Bluetooth

Lights intermittently responding to app|

Loose connection. Moisture or corrosion in connections

|

Inspect quick-connected plugs for moisture or corrosion. Clean/dry/apply dielectric grease and reassemble.

1.330.274.8317
www.ATLANTIC-OASE.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>