LiFE Mistral Stand Fan with Remote Control 50W User Manual

Stand Fan with Remote Control 50W
User Manual

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS.

Read the operating instructions carefully before putting the appliance into operation and keep the instructions, the receipt, and, if possible, the box with the internal packing. If you give this device to other people, please also pass on the operating instructions.

USER MANUAL SYMBOLS

Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the machine:

WARNING: This sign warns you of dangers to your health and indicates possible injury risks.
CAUTION: This sign refers to possible hazards to the machine or other objects.
NOTE: This sign highlights tips and information

GENERAL NOTES

1. Use the fan only for purposes described in the instruction manual.
2. The appliance is designed exclusively for private use and for the envisaged
3. Always use on a dry, level surface.
4. To protect against electrical shock, do not immerse the fan, plug or cord in water or any other liquid or spray with liquids.
5. Unplug from the electrical outlet when not in use, when moving the fan from one location to another, before putting on or taking off parts and before
6. Do not operate the machine without supervision. If you leave the room you should always turn the device off.
7. The protective grills are to prevent direct access to moving parts when the fan is in use Avoid contact with any moving parts.
8. CAUTION: To avoid injury, do not insert your fingers between the grilles when the appliance is plugged in or when it is turned on.
9. CAUTION: Do not place clothes or other objects on the fan
10. CAUTION: Do not use the appliance near the curtains.
11. Do not operate any appliance, with a damaged cord plug after the appliance malfunctions, or has been dropped damaged in any manner.
12. The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
13. Do not use the appliance before assembling it.
14. Do not use the appliance outdoors.
15. Do not use the appliance in the bathroom, in swimming pools or in rooms with high humidity levels, or in dusty areas.
16. To disconnect from the electrical supply, grip the plug and pull from the wall DO NOT pull on the cord.
17. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person in order to avoid a hazard.
18. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
19. Children should be supervised to ensure that they do not play with the In order to ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene, etc.) out of their reach.

CAUTION: Do not allow small children to play with the foil. There is a danger of suffocation!

BATTERY SAFETY INSTRUCTIONS (OF REMOTE CONTROL)

1. Different battery types or new and used batteries must not be used together.
2. Batteries can leak and lose battery acid. If the remote control is not used for a long period of time, remove the batteries.

PARTS IDENTIFICATION

STAND FAN

1. Front grille
2. Blade cap
3. Blade
4. Nut
5. Rear grille
6. Motor shaft
7. Motor
8. Control panel with touch buttons
9. Supply cord
10. Screw A
11. Inner pipe
12. Base pipe
13. Screw B
14. Base with cap
15. Base pipe screw

REMOTE CONTROL

1. ON / OFF button
2. SWING: Oscillation button
3. Timer button
4. Mode selection button
5. Speed selection button

ASSEMBLY

1. Place the base cap on the base.

2. Loosen the base pipe screw by turning counterclockwise from the base pipe, remove it and Insert the base pipe down to the base. Secure the base pipe to the base with the base pipe screw.

3. Loosen screw B and pull the inner pipe out. Then tighten the screw again to secure it.

4. Loosen the control panel screw (screw A) by turning it counterclockwise, Insert the control box firmly down the inner pipe, and secure it by turning screw A clockwise.

5. Loosen the blade cap by turning clockwise and the rear guard mounting nut by turning counterclockwise. (Fig1)

6. Place rear grille on motor shaft and secure with rear mounting nut. (F1g2)

7. Slide blade on motor shaft and secure with blade cap by turning counterclockwise. (Fig3 and Fig 4)

8. Place the plastic cap into the front grille and secure it with the screws contained.

9. Place the front grille on the rear grille and close clips, and then fix together with screw and nut provided. (Figs)

OPERATING INSTRUCTIONS

1. Set the fan on a dry, level surface.
2. Before connecting the appliance, make sure that the power supply of your appliance corresponds exactly to the voltage of your electrical installation.
3. Press the ON/OFF button to turn on the fan. The appliance turns on to NORMAL mode (standard continuous operation to speed 3) automatically. To turn the fan off, press the ON/OFF button again.
4. Stand fan has 3 operation modes:

• NORMAL (standard continuous operation to speed 3)
• SLEEP (silent night mode at the lowest speed operation)
• NATURE (wind effect operation – device changing its speed simulating the wind)

Select the desired operation mode by pressing the corresponding button on the fan or on the remote control.

5. The SPEED is adjusted by pressing the speed switch for your desired level of cooling comfort.

TIMER
The timer can be set to switch the fan off at a time that you can program. Press the TIMER button to set the timer. With each push of TIMER, the time setting is increased for one hour e.g. if you press the TIMER button three times, the indicator will light up and the fan will operate for three hours. When the fan is turned off, the previous timer setting will be lost.

OSCILLATION MODE

To start and stop the oscillation of the fan head, press the SWING button on the fan or on the remote control. Press the SWING button again to stop the oscillation function.
j NOTE:
All fan functions can be selected either from the remote control or by pressing the buttons on the control panel of the fan.

CLEANING AND MAINTENANCE

Follow these Instructions to correctly and safely care for your fan.
Please remember:

1. Always unplug the fan before cleaning or assembly.
2. Do not allow water to drip on or into the fan motor housing.
3. Be sure to use a soft cloth, moistened with a mild soap solution.
4. Do not use hard, abrasive or corrosive detergents or solvents or any of the following as a cleaner: petrol, thinners or benzene to clean the device

FAN STORAGE
Your fan can be stored other partially disassembled or assembled. It is important to keep it in a safe, dry location.
If stored disassembled, we recommend using the original (or appropriately sized) box.

Made in China
Ionias Kalochori, 570 09
Thessaloniki, Greece,
TEL. +30 2310 700.777
e-mail: info@sun.gr 
www.Iife.gr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>