auraLED 7358 6.5 Inch LED Bulb and Light Strip User Manual
- June 6, 2024
- auraLED
Table of Contents
auraLED 7358 6.5 Inch LED Bulb and Light Strip
INTRODUCTION
ColorBulb
The aural ColorBulb allows you to turn on the lights automatically in a smart
and ingenious way from any location. Simply connect to your home and enjoy
multiple features of this state-of-the-art smart LED light bulb. Includes a
wireless remote controller, which provides you with the freedom to customize
your selection of 16 colors and find the perfect brightness, rhythm, and color
scheme
ColorStrip LED
Give your home living room a unique atmospheric twist with the ColorStrip LED
lights by Izumi. Designed with a safe adhesive backing, this colortul
backlight can be fixed directly onto the back of your 1V or computer screen,
enhancing your home theater and easing light-induced fatigue. It fits screens
up to 65″ and includes a wireless remote controller, which provides you with
the freedom to
customize your selection of 16 colors and find the perfect brightness, rhythm,
and color scheme
WHAT’S IN THE BOX?
1x 6.5 Ft LED Mood Light 1x Wireless Remote Control
2x A24 LED ColorBulb light bulb
1x User Manual
PRODUCT OVERVIEW & FUNCTIONS
Wireless Remote Control
When Remote Control operation becomes slow, it is time to change the battery.
CompatiblewithCR2025andCR2032batterytypes
INSTALLATION
ColorStrip LED
NOTE: Please make sure that the back surface of your 1V is Clyburn L from
Mdouosdt, Loiiglsh, or fingerprints before attempting to apply t. Use an
alcohol-based cleaning cloth to wipe the back of your 1V.
-
Loca /& te the USB port on the back of your 1V. If your ‘e::J 1V does not have a USB port, you may use any other ‘ USB power source.
-
Make sure that you are satisfied with the coverage area of the LED strip prior to peeling off the adhesive tape. Ma1 ke sure that the USB cable is placed near the USB port and has enough 1
, slack to reach safely. The Remote Receiver must also be visible, in order to work properly. See below. -
Peel off the backing of the strip to expose the a, adhesive.
-
Apply to the cleaned surface of the abuse can we, of TV. Press down for a couple of seconds t1 o secure.
ASSEMBLY
WIRELESS REMOTE CONTROLS
- Brightness (Down)
- Brightness up
- Power OFF
- Power ON
- LED Color Buttons -16 color.
- Flash Transition Effect
- Strobe Transition Effect
- Fade Transition Effect
- Smooth Transition Effect
When remote control operation becomes slow, ii is time to change the battery. Replace with a new cell battery ·compatible with CR2025-CR2032 battery types
LED LIGHT STRIP SPECS
ColorBulb SPECS
CARE & IMPORTANT SAFEGUARDS
- Always make sure that all parts have been connected properly
- Check to make sure the voltage of the power source (USB) is 5V.
- Do not connect the LED strip to the power source until all of the installations have been completed.
- Do not cut any part of the LED strip or its connectors.
- Always make sure that the Remote Receiver is not covered or blocked. This will ensure proper operation using the remote control.
- If this product malfunctions, please do not try to repair it yourself, take it to a qualified electrician.
IMPORTANT SAFEGUARDS
This device complies with Part 15 of the FCC Rules. Operation is subject to
the two following conditions:
1. This device may not cause harmful interterence
2. This device must accept any interterence received, including interference
that may cause undesired operation
IMPORTANT : This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
Accordance with the instructions, may cause harmful lnterterence to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interterence to radio or television reception, which can be determined by
turning the equipment oft and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-
reorient or relocate the receiving antenna.
-
increase the separation between the equipment and receiver
-
and connect the equipment into an outlet on a circuit different from thato which the receiver is connected.
-
consult the dealer or an experienced radio/TV technician for help.
-
To satisfy FCCC/RF exposure environments a separation distance of 20 cm or more should be maintained between the antenna of this device an<I persons during device operation. To ensure complia1 nice, operations at closer to this distance is not recommended.
Read and follow precautions before installing -
Use in a dry location only – Risk of electric shock or burns
-
Do not install this device with wet hands or while standing on damp and wet surfaces.
-
Suitable for use in an operating environment between -10 C and 40 C (14 F and 104 F)
-
Not for use in totally enclosed lamps. Do not use with dimmers. Ensure that the voltage of the LED light bulb is compatible with the main electricity of your country before connecting to a bulb holder. Ensure that the base of the bulb matches the bulb holder. When the light bulb reaches the end of its cycle the bulb should be replaced use and/or care, please contact Izumi Technical Support at: support@tzumi.com or 1-855-Go-TZUMI.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>