H Koenig v6 Steam Iron Instruction Manual

Instruction Manual

Steam ironing system
Centrale vapor
http://goo.gl/x1A4Ks

IMPORTANT SAFEGUARDS

1. Make sure to read all the safety precautions below and look at the illustrations before you start using the appliance.
2. Use the appliance for its intended use only described in this manual.
3. The appliance is intended for household use only.
4. In order to protect against the risk of electric shod, do not immerse iron power base into water or any other liquids.
5. Connect the appliance only to an alternating current of the voltage specified on the rating plate and only to an earthed socket. To avoid a circuit overload, do not operate another high wattage appliance in the same circuit.
6. Turn the appliance to OFF before plugging or unplugging from the outlet. Never yank the cord to disconnect from the outlet; instead, grasp the plug and pull to disconnect.
7. Do not allow the power cord or supply hose to touch hot surfaces.
8. Unplug the appliance from the main socket before filling or emptying or when not in use.
9. Do not operate the appliance with a damaged cord or if the appliance has been dropped or damaged. To avoid a hazard such as the risk of electric shock, do not disassemble the appliance, it must be taken to a qualified serviceman or manufacturer or its service agent for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.
10. Place the iron out of reach of children; close supervision is necessary for any appliance being used by or near children. Do not leave the iron unattended while connected to the supply mains.
11. During use, always place its stand on a stable, level, and horizontal surface or ironing board.
12. Always place the iron on its stand, and do not allow the hot soleplate to touch the power cord or supply hose.
13. Burns can occur from touching hot metal parts, hot water, or steam. Use caution when using the appliance.
14. Never use the iron facing towards people because the steam can cause burns.
15. Never twist the supply hose during use.
16. The appliance must be used and rested on a stable, level, and horizontal surface.
17. The iron shall be placed on the separate stand only.
18. When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
19. The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.
20. The iron must not be left unattended while it is connected to the supply mains.
21. The appliance must be rested or stocked on a stable, level, and horizontal surface.
22. During use, if no water in the reservoir, it will produce noise <70dBA.
23. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved, children shall not play with the appliance.
24. Cleaning and user maintenance shall not be made by children without supervision.
25. Keep the iron and its cord out of reach of children less than 8 years of age when it is energized or cooling down.
26. This appliance may be used by children of at least 8 years of age, as long as they are supervised and have been given instructions about using the appliance safely, and are fully aware of the dangers involved.
27. Cleaning and maintenance should not be carried out by children unless they are at least 8 years of age and are supervised by an adult.
28. When using electrical equipment, safety precautions must always be taken to prevent the risk of fire, electric shock, and/or injury in the event of misuse.
29. Make sure that the voltage rating on the type plate corresponds to the main voltage of your installation. If this is not the case, contact the dealer and do not connect the unit.
30. The device must not be used if it has been dropped, if obvious signs of damage are visible or if it has leaks.
31. The device is not intended to be operated by external timer means or a remote control system.
32.  This appliance is only intended for domestic and indoor use.
33. Never immerse the appliance, its power cord, or the power outlet in water or any other liquid

PARTS AND FEATURES

1. Water tank
2. Handle
3. Sole-plate
4. Fabric setting display
5. Selection button
6. Steam release
7. Power cord/Connecting supply
8. Power cord
9. Handle button
10. Filter
11. Water tank lock

Fabric Setting Chart

Ironing Temperature Setting Guide

1. Follow up on the ironing instructions on the garment label. If there is not any instruction label, but you know what kind of the fabric is, please refer to the fabric setting chart described in this instruction manual.
2. The fabric setting chart is only validfor plain fabrics and not for materials to which finishes, glosses, etc., have been applied. Textile to which some kind of finish has been  applied (gloss, crinkle, relief, etc.) is best ironed at a lower temperature
3. First sort laundry according to the ironing temperature setting guide: wool with wool, cotton with cotton, etc.
4. The iron heats up more quickly than it cools down. Therefore, start ironing articles that need to be ironed at the lowest temperature, such as those made of synthetic fibers.
5. If the fabric consists of various kinds of fibers, always select the temperature required by the most delicate fibers, i.e.the lowest temperature. If, for example, an article consists of 60% polyester and 40% cotton, according to the fabric setting chart it should be ironed for polyester.
6. If you do not know what kind of fabric the article is made of, iron a piece of the material which is not visible when you wear it to find out the appropriate temperature for your article.
7. Pure woolen fabrics (100% wool} should be ironed with the iron set to steam ironing position. lt is advisable to set the selection control button to the “Cotton” position and use a dry pressing cloth.
8. When steam ironing woolen fabrics, shiny patches may occur. You may prevent this by turning the article inside out and ironing the reverse side.
9. After using steam ironing for cotton fabrics, do not iron articles required by lower temperatures (such as nylon, etc.) immediately. lt is advisable to adjust the selection button to the lower setting, waiting for about 2-4 minutes till the blue indicator light turns off, and then you can start ironing.

IMPORTANT HINTS:
Do not fill the water tank with vinegar, perfume, starch, chemically descaled water, or descaling agents.

How to use your steam station

Prepare the appliance for use

1. Check if the rating indicated in the rating plate corresponds to the main voltage in your home
2. Press the handle button to lay the handle down. (Fig.1 ) (Note: When the handle lifts up, the unit is shut off, it will be ON when the handle is laid down.)
3. Remove the protective foil or sticker or card from the soleplate.
4. Fully unwind and straighten the power cord and the supply hose.
5. Place the appliance on a stable, level, and horizontal surface, such as an ironing board.
6. Place the iron onto the iron rest plate horizontally at the base unit.

Fill water tank

1. Press the water tank lock upwards and slide the detachable water tank outwards from the base. (Fig.2)
2. Take the filter upwards out from the water fill hole. (You can take the filter out of the opening for filling water into the water tank or fill water into the water tank directly with the filter existing in the opening big.3)
3. Fill the water tank up to or below the “MAX” fill line with clean tap water. (Fig.4)
4. Replace filter back into water filling hole. (Fig.5)
5. Replace the water tank with the base unit again. It will be locked in place with the base unit until a ‘dick ” sound is provided. (Fig.6)
6. Always pour out the remaining water after use. (Fig.7)
   Note : When the water level reaches a low level or is empty, the pump will provide a sound to indicate refilling. It must stop using the appliance immediately and refill the water tank as the methods mentioned above.

Steam ironing

1. Fill the water tank with clean tap water refer to the above filling instruction. For better performance, please immerse the filter in water for several minutes before installing it into the water tank)
2. Connect the appliance to a suitable socket outlet, power indicator light (red) ” Q.) “at the iron unit lights up, it shows that the unit has been connected to the power supply. (FIG.8)
3. Set the selection button to the desired position according to the fabric setting chart mentioned above. (FIG.9) Setting indicator light (blue) at the iron unit blinks slowly to indicate the unit is heated up. When the blue indicator light change to light up steadily and an audible “Bi” signal is produced, the desired temperature has been reached. It is ready for steam ironing. During use, the temperature indicator light sometimes blinks and sometimes lights up steadily, it does not indicate a defect or hazard, it is just because the appliance is temperature constant.
4. Before every first time use, it is proposed to clean the iron unit as following methods: Take the iron up from the base unit, press the steam button underneath the handle to allow steam ON for 30 seconds, and then OFF for 30 seconds, this cycle should be repeated for 2 times. When the blue indicator light stops blinking, it is ready for use.
5. During steam ironing, steam should be automatically adjusted according to sole-plate temperature, which can most effectively prevent water from trailing from the soleplate.
6. After use, put the iron unit back onto the base unit again, set the selection button to” ****“, and then unplug the appliance from the main socket
7. Slide-out the water tank and pour out the remaining water.

Note:
a. For every first-time use, it is normal that is a slight vibration sound may occur from the electrical pump inside the base unit for a few seconds when steam ironing started. It is because there is air inside the filter, it will stop till the air inside the filter has been pumped out. If these abnormal conditions continue to happen for more than 60 seconds, please check whether the water tank and filter are assembled correctly or not
An a. When setting the selection button at the “NYLON” position, no steam escaped since it only just suits dry ironing.
b. When set fabric setting at “POLYESTER” / “RAYON” / “CAUTION”
“LINEN”, steam will automatically vary according to sole-plate temperature. The pump will stop working and no steam escaped when the sole-plate temperature decreases too low. lt will resume after reheating to the desired temperature.
Dry ironing

1. Connect the appliance to a suitable socket outlet, and lay the handle down. The power indicator light (red} “<!) “on the iron unit lights up, it indicates that the unit has been connected to the power supply.
2. Set the selection button to the desired position according to the above fabric setting chart. The blue indicator light at the iron unit blinks slowly to indicate the unit is heated up. When the blue indicator light change to light up steadily and an audible “Bi” signal is produced, the desired temperature has been reached. During use, the blue indicator light will cycle from blinking to light on steadily, and then from steady mode to On. lt does not indicate a defect or hazards, it is just because the appliance is temperature constant.
3. After use, put the iron unit back onto the base unit again, turn the selection button to” <!) “, and then unplug the appliance from the main socket.
   Note: When changing your Temp setting from higher setting to lower, it is proposed not to start ironing immediately since it may cause burns to your fabrics. Please wait  till the blue indicator light lights up steadily, and then start ironing.

Vertical steam ironing

Follow the steam ironing process, and then hold the iron in a vertical position between 5cm and 15cm away from the hanging fabrics. Press down the steam switch, this will create vertical steam. This feature is especially used for removing creases from hanging clothes and curtains. Never directly perform steam ironing on people.
Auto shut off function
The appliance will corne into auto shut off mode along with audible “Bi…” signal when it has been used for 60 minutes continuously with temperatures at any settings, power  indicator light” c!)”Blink. Press the selection button to reset another 60 minutes cycle if continuous use is necessary. (Note: once each setting is pressed, the unit will reset time)
Handle
Handle attached to the base unit used to carry the appliance, it also serves as a power on/off switch: Lift the handle up, power OFF, put the handle down, power ON. Before use, please put the handle down as the following method: Press down two handle buttons synchronously, and then lay the handle down. (Fig.10)After use, allow the appliance completely cool down, then wind the power cord around the cord storage of the base unit and put the iron onto the base unit. Lift the handle up until a click – sound is provided, it indicates that the handle has been locked in place and you can carry the appliance by the handle. (Fig.1 1)
Cord storage

1. Unique design for cord storage of base unit provides not only beautiful features but also easy storage.
2. After use, unplug the unit from the main socket and pour out the remaining water from the water tank after the unit has been completely cooled down.
3. Rest the iron-on power base, fold connecting supply in half, (FIG.12) and wind the connecting supply counterclockwise around the cord slot of the base unit. (Fig.13) Then tie the power cord and connecting supply with the cord tie at the nearly ended area. Wind the remaining power cord clockwise around the card slot, then put a plug between connecting supplies in order to tighten fully. (Fig.14)
4. Well, store the appliance for further use. Note: This feature is not included for model G-1033STB-E.

Replacement of filter

Method: SIide the water tank out from the base unit, take the filter out from the water tank, and then replace it with a new one. After the new filter has been installed well into the water tank, fill water the water tank to Max fill level and then slide the water tank back into the base unit. (Immerse filter in water for several minutes in order to gain better performance in future use.

Anti-calc system

1. The filter is designed to reduce the buildup of limescale which occurs during steam ironing,
   this will prolong the working life of your iron. However, please note that the filter will not
   completely stop the natural process of limescale build-up.

2. The filter should be replaced with a new one after two-three months. Before replacement, the filter can still be used continuously. However, timescales may be most probably built up in the steam chamber, This happens always depending on your local water quality. 1 t is proposed that replace filter as soon as possible or mix your water with 50% proportion of distilled water.

Emptying and storing

1. Disconnect the appliance from the power supply and allow the appliance to cool down for 60 minutes at least.
2. After use, slide out the water tank and pour out all the remaining water.
3. Wind the power cord around the cord storage of the base unit.
4. The iron should be placed on the iron rest plate and they can store together.

Cleaning and Maintenance

1. Unplug the appliance tram the main supply and let the iron cool down.
2. Clean the iron with a damp cloth.
3. Wipe off the scale and any other deposits on the soleplate with a damp cloth or non-abrasive (liquid) cleaner. Never clean the appliance under the tap water.

Troubleshooting

the main socket.
The handle has not been laid down| Lay handle down
Temp setting at ” <!> ” position| Select the required ironing temperature according to the fabric setting chart.
Unknown malfunctions| Take to a qualified serviceman or manufacturer or its service agent for examination and repair.
No steam goes out when pressing the steam switch after the desired temperature is reached.| Temp   setting  at NYLON position| Select the required ironing temperature according to the fabric setting chart.
No water in the water tank| Fill water into the water tank
The filter has not been well installed into the water tank.| Install filter into the water tank
The water tank has not been well installed.| Slide the water tank into the power base and it will be locked in place until a “click” sound is produced.
”     <!> ”  blink quickly, other fabric indicators turn off,     buzzer sound a “Bi”.All buttons are non- working.       it will resume when re-energized again.| Defects with the internal circuit, the unit comes into self protect mode| Re-energized the unit again. If it still can not resume, please take it to its service agent or similarly qualified persons for repair.

Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of electrical and electronic products. The correct disposal of your old product helps prevent potentially negative consequences on the environment and human health.

Adeva SAS / H.Koenig Europe – 8 rue Marc Seguin, 77290 Mitry-Mory, France
www.hkoenig.com – sav@hkoenig.com – contact@hkoenig.com – Tél: +33 1 64 67 00 05

References

• low.lt - Užregistruotas domenas - Interneto vizija
• H.Koenig : Le spécialiste du petit électroménager

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>