MASTER TR 3C Electric Air Heater User Manual

MASTER TR 3C Electric Air Heater

SAFETY INFORMATION(Fig. 1)

This series of warm air heaters is particularly suited to heating Vareas, such as warehouses, shops, restaurants and homes. These heaters comply with the current European directive.
IMPORTANT:

• You are required to read and understand this operational manual prior to assembling, starting up or conducting maintenance on this heater. Using the heater incorrectly can cause serious injury. Keep this manual for future reference.
•  This heater is not suitable for use by persons (including children) with reduced physical, sensory or mental capacities or with lack of experience or knowledge unless supervised by a person responsible for their safety. Children must be supervised to make sure they do not play with the heater.
• In order to prevent any risk, even if power supply mains disconnection is foreseen, all cleaning, maintenance and repair operations requiring access to dangerous parts (e.g. replacing the damaged power supply cable), must be carried out by the manufacturer, its technical support centre, a person with similar qualification.
• Comply with all local legislation and current regulations when using the heater.

SAFETY INSTRUCTIONS

1. Heaters used near tarpaulins, curtains or other similar covering materials must be a safe distance from them. It is advised to use fire-proof covering material.
2. Keep the heater a safe distance from humidity, water and atmospheric agents to prevent serious damage to the heater.
3. Keep the hot parts of the heater a suitable distance from inflammable or thermolabile materials (including the power supply cable).
4. Do not handle or conduct maintenance on the heater when it is hot, connected to the mains or in operation.
5. For correct use, install the wall heater using suitable fixing plugs. The wall used for installation must be adequate to support the weight of the heater. DO NOT USE THE HEATER WHILE PLACED ON THE GROUND.
6.  Keep animals at a safe distance from the heater.
7.  Power on the heater only with a current which has the voltage and frequency values specified on the heater’s identification plate.
8. Make sure the heater is only connected to suitable mains with a differential switch and suitable earthing.
9. If the power supply cable or the remote room thermostat are damaged, they must be replaced by a technical support centre to prevent any risk.
10.  Disconnect the heater from the mains power supply when not in use for a prolonged time.
11.  Always disconnect the heater from the mains if temporarily left in unsafe conditions and in any case make sure it cannot be used.
12. Never block, not even partially, the heater’s air vent (rear) or the air outlet (front).
13. Avoid ducting the air.
14.  Do not cover the heater while in operation, it might overheat.
15.  Ask the technical support service to check that the heater is working properly at least once a year and/or as required.

THE MANUFACTURER DECLINES ANY LIABILITY FOR DAMAGE/INJURIES TO PROPERTY/PERSONS DERIVING FROM IMPROPER USE OF THE HEATER. ONLY SPECIALISED PERSONNEL AUTHORISED BY THE MANUFACTURER CAN PERFORM WORK ON THE HEATER.

UNPACKING

WARNING: The packaging material is not a toy. Keep the plastic bag out of the reach of children; danger of suffocation!

1. Remove all packaging material used to deliver the heater and dispose of it in compliance with current standards.
2.  Remove all items from the packaging.
3. Check for any damage incurred during transport. If the heater appears damaged, immediately inform the dealer from whom it was purchased.

DESCRIPTION(Fig. 2)

• A. Wall support.
• B. Adjusting screw.
• C. Fastening screw.
• D. Heater.
• E. Main power supply switch.
• F. Reset.
• G. Power supply cable.
• H. Remote room thermostat.
• I. Room thermostat display.
• L. Remote room thermostat temperature sensor.

ASSEMBLY AND INSTALLATION (Fig. 3)

For the assembly and installation of the heater, carefully follow the instructions below.
The mechanical parts, which come with the relative nuts and bolts,are always in the heater’s packaging and must always be assembled before the product is turned on.
THE HEATER MUST BE INSTALLED ACCORDING TO LAW, USING COMPONENTS IN COMPLIANCE WITH LOCAL AND/OR NATIONAL REGULATIONS. THE MANUFACTURER DECLINES ANY LIABILITY FOR DAMAGE/INJURIES TO THE HEATER AND/OR PERSONS DERIVING FROM INCORRECT INSTALLATION.

OPERATION

WARNING:

• You are required to read, understand and follow the ”INFORMATION ON SAFETY” before starting the heater in order to use it correctly and avoid risks.
•  Make sure the power supply cable is intact and that the features of the mains power supply match the ones on the heater’s technical data plate.
• Never use the heater without first assembling all the components correctly. For correct use, install the wall heater using suitable fixing plugs. The wall used for installation must be adequate to support the weight of the heater. DO NOT USE THE HEATER WHILE PLACED ON THE GROUND.

SWITCH-ON:

1. After installing the wall heater, connect the heater plug to the electrical mains (Fig. 4) and set the main power switch to “I / ON”. The display shows the room temperature.
2.  Turn on the heater using the “ON / OFF “ button of the remote room thermostat and select the desired mode using the arrow buttons “↑ ↓”. The following modes are available:

• * PROGRAM 1: Manual program (heating and ventilation) (Fig. 5).

  •  PROGRAM 2: Automatic heating program (ECO heating) (Fig. 6).
  • PROGRAM 3: Advanced program, only for qualified personnel.
  • PROGRAM 4: Advanced program, only for qualified personnel.

During use, the remote room thermostat automatically locks the keyboard. To unlock the keyboard of the remote room thermostat, press the arrow buttons simultaneously ”↑↓”.

CAUTION: A SERIES OF SENSORS CHECK THAT THE HEATER IS OPERATING CORRECTLY AND STOPS THE APPLIANCE IN THE EVENT OF A SERIOUS FAULT. THE HEATER WILL NOT RESUME OPERATION AUTOMATICALLY, THIS MUST BE PERFORMED MANUALLY. WAIT FOR THE HEATER TO COOL  DOWN COMPLETELY AND REMOVE ANYTHING WHICH MIGHT HAVE BLOCKED THE HEATER (E.G. OBSTRUCTED AN AIR VENT, IMPAIRED THE AIR SUPPLY, ETC.) AND FULLY PRESS THE “RESET” BUTTON LOCATED AT THE BACK OF THE HEATER. IF, AFTER A FEW ATTEMPTS TO RESUME OPERATION, THE HEATER DOES NOT WORK, CONTACT THE TECHNICAL SUPPORT SERVICE.

SWITCH-OFF:

1.  Turn off the heater with the “ON / OFF “ button of the remote room thermostat and leave the fan running until the heater is completely turned off (if the keyboard of the remote room thermostat is locked, press the arrow buttons simultaneously ”↑↓”).
2. Disconnect the heater from the mains.
   CAUTION: AVOID DISCONNECTING THE HEATER FROM THE MAINS BEFORE THE FAN HAS COMPLETELY STOPPED MOVING TO AVOID SERIOUS DAMAGE.

 STORAGE

Always unplug the heater from the mains during a long downtime. Put it back in a dry place and protected from dust. When the heater is used again, check the condition of the power supply cable. If in doubt regarding its state, contact the technical support centre. In any case, have the technical support centre check that the heater is working properly at least once a year and/or as required.

REMOTE ROOM THERMOSTAT

For correct operation, the heater must be connected to the mains and have the main power switch set to position “I / ON”. When the remote room thermostat is activated, the heater can turn on at any time when the temperature drops below the set temperature

TROUBLESHOOTING

2.  Incorrect setting of the remote room thermostat

3.  No power supply

4.  Blocked heater

| 1. Set the main power supply switch to “I / ON”

2a. Turn on the heater using the “ON / OFF“ button of the remote room thermostat and select the desired mode

2b. Make sure the temperature set on the remote room thermostat is higher than the outdoor temperature

3a. Insert the power supply cable correctly

3b. Make sure your mains power supply is working correctly 3c. Contact a support centre

4a. Turn the heater back on 4b. Contact the support centre

The motor doesn’t work| 1.  Faulty motor

2.  Fan blocked

| 1. Contact the support centre 2a. Remove any obstructions 2b. Contact the support centre
The heater doesn’t heat| 1.  Remove room thermostat set to “VENTILATION”

2.  Faulty internal appliance

| 1.  Modify the setting of the remote room thermostat

2.  Contact the support centre

Reduced airflow| 1.  Obstructed air vent

2.  Faulty motor

| 1a. Remove any obstructions 1b. Contact the support centre

2. Contact the support centre

WIRING DIAGRAMS

TECHNICAL DATA TABLE

кВт

| 1,65 – 3,3| 4,5 – 9
kcal/h

ккал/ч

| 1.433 – 2.866| 3.870 – 7.740
Max current cons.| A| 13,5| 13,5
Voltage| V/Hz

В/Гц

| 220-240 / 50| 380-400 / 50
Air displacement| m³/h

м³/ч

| 510| 800
Temperature range| o C| 5-35| 5-35
Dimension L x W x H| cm

cм

| 27x25x34| 33x28x38
Resistance norm| | IP24| IP24
MODEL| TR 3C| TR 9C
---|---|---
| SYMBOL| UNIT| |
HEAT OUTPUT
Nominal heat output| Pnom| kW| 3,3| 9
Minimum heat output (indicative)| Pmin| kW| 1,65| 4,5
Maximum continuous heat output| Pmax,c| kW| 3,3| 9
AUXILIARY ELECTRICITY CONSUMPTION
At nominal heat output| elmax| kW| N/A| N/A
At minimum heat output| elmin| kW| N/A| N/A
In standby mode| elSB| kW| 0,00076| 0,00076
TYPE OF HEAT INPUT, FOR ELECTRIC STORAGE LOCAL SPACE HEATERS ONLY (SELECT ONE)
Manual heat charge control, with integrated thermostat| No
Manual heat charge control with room and/or outdoor temperature feedback| No
Electronic heat charge control with room and/or outdoor temperature feedback| No
Fan assisted heat output| No
TYPE OF HEAT OUTPUT/ROOM TEMPERATURE CONTROL (SELECT ONE)
Single stage heat output and no room temperature control| No
Two or more manual stages, no room temperature control| No
With mechanic thermostat room temperature control| No
With electronic room temperature control| No
Electronic room temperature control plus day timer| No
Electronic room temperature control plus week timer| Yes
OTHER CONTROL OPTIONS (MULTIPLE SELECTIONS POSSIBLE)
Room temperature control, with presence detection| No
Room temperature control, with open window detection| No
With distance control option| No
With adaptive start control| Yes
With working time limitation| No
With black bulb sensor| No
Conctact Details (See the CE CONFORMITY CERTIFICATE)

ATTENTION: This product is only suitable for well insulated spaces or occasional use.

 DISPOSAL OF THE PRODUCT

• This product has been designed and manufactured with top-quality materials and components, which can be re-cycled and re-used.
• When a crossed-wheely bin symbol is attached to the product, it means that the product is protected by the, 2012/19/UE European

Directive.

• Please obtain information regarding the local differentiated collection system for electrical and electronic products.
• Respect local Standards in force and do not dispose of old products as normal domestic waste. Correct disposal of the product helps to prevent possible negative consequences for health, the environment and mankind.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>