poooli MT800 Portable A4 Thermal Printer User Guide

MT800 Portable A4 Thermal Printer

Quick Start Guide
MT800

Operation Procedure (From Mobile Phone)

1. Power on: Hold down the power button for
3 seconds, and then release it when the printer
is turned on. (Power button is touch button)

Note: In power-on status, hold down the power button
for 3 seconds to turn off the printer.

2. Loading paper: Put the paper into the paper
inlet in parallel. Printer will feed a distance
automatically after it detects the paper. If the
buzzer sounds once when paper feeding stops,
it shows that the paper is loaded successfully
and the printer is ready.

Package List

Note:

1. The packing items are actually dependent
   on the order.

2. The ribbon module is embedded in the
   printer when leaving the factory|

3. Download “Poooli A4” APP: Scan the QR
code below to download the APP.

4, Connect with the printer:

Open APP, click “Unconnected device” on
the top right corner, find “Poooli A4-XXXX”
(XXXX indicates last four digits of Bluetooth
address) in the list of “Connectable devices”,
click to connect. After connection succeeds,
return to the homepage.

5. Print: Choose the file to print, click the
print icon on the top right corner to enter
print preview, click “Print now” that the
printer will conduct printing.

Appearance and Components

Front

Left

Note: indicate Bluetooth Function

Operation Procedures

(From Computer)

1. Connect the printer to the computer:
Connect the printer to the computer via
Bluetooth/USB, and then install the printer
driver on the computer.

Driver can be downloaded from the website:
http://www.poooli.com/download/a4

Inner

LED Indicator

White LED indicator stays on:
Printer is in standby status

Green LED indicator stays on:
Printer is in charging mode, and green LED
Indicator will be off  when fully charge

Red LED stays on:
Printer is out of ribbon, please replace it

NOTE:

Poooli A4 is only suitable for computer USB port power supply, please use the exclusive USB charging cable to connect to the computer for charging.

2. Install Driver:

1. Double click the driver program.
2. Choose the setup language “English” and mclick “Ok”.

Loading Ribbon

1. Press the [PUSH] button on both sides of the printer at the same time, then lift the printer cover upward.

A NOTE:

The environmental condition of the ribbon is
as below:
Operating Temperature: 5°C~35°C
Operating Humidity: 20%~85%RH
Storage Temperature: -5°C~45°C
Storage Humidity: 20%~85%RH

3 Click “Next”

4 Click “Finish”

2. Hold the left and right wings of the ribbon by your hands, then align it to the place with the arrow marked on the printer and press it down

A NOTE:

To avoid errors when installing ribbon, please make sure that the arrow direction marked on the ribbon module is the same as the arrow direction marked on the printer.

5. After installation, the icon can be found in “Start” > “Devices and Printers”.

3. Loading paper: Please refer to the second
step from “Operation Procedures (From Mobile
Phone)’.

4. Print: Open the file to print, choose “Poooli
Aa” for printer device, click “print”.

General Problem

1. When the button is abnormal and can’t
respond, how to deal with it?

Please remove the ribbon, lightly hold down
the [Reset] button with toothpick or pin for 2
seconds, then turn off the printer and restart
it.

3. Rotate the ribbon rewind wheels of both
top left and lower right (or top right and lower
left) towards the center simultaneously to
make it smooth.

4. Press down the cover by hand until it click into place.

Removing Paper

NOTE:

Don’t pull the paper out forcefully while the
printer cover is closed, or it may damage the
printer. Please remove the paper as follows.

1. Press the [PUSH] button on both sides of
   the printer at the same time, then lift the
   printer cover upward.

2. Remove the paper.

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications
not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines,

This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>