JMAZ LIGHTING ATTCO BEAM Color LED 230 Moving Head User Manual

: June 13, 2024
: JMAZ LIGHTING

Table of Contents

JMAZ LIGHTING ATTCO BEAM Color LED 230 Moving Head
Product Information
Product Usage Instructions
Safety instructions
BEFORE YOUR INITIAL START-UP
Maintenance and cleaning
UNPACKING
TECHNICAL INFORMATION
DMX PROTOCOL
PHOTOMETRICS DIAGRAM
OPERATION INSTRUCTIONS
INSTALLATIONS
Operation Guide for the Wireless DMX
CONTROL CONNECTION
MENU OPERATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JMAZ LIGHTING ATTCO BEAM Color LED 230 Moving Head

Product Information

Product Name: ATTCO BEAM 230
Manufacturer: JMAZ Lighting
Address: 2422 Lee Ave, South El Monte, CA 91733
Phone: 1-626-380-0883
Website: www.jmazlighting.com
Email: [email protected]
Version: 1.0

Product Usage Instructions

Safety Instructions:
Thank you for choosing our ATTCO BEAM 230. Please read this user manual carefully before you initially start up the product.

CAUTION! Be careful with your operations. High voltage can cause dangerous electric shock when touching the wires.
CAUTION! Keep the device away from rain and moisture. Unplug the mains lead before opening the housing.
CAUTION! Avoid looking directly into the light source, especially for epileptics.

Maintenance and Cleaning:
Regular cleaning is essential to maintain the maximum light output and ensure reliable operation throughout the product’s life.
DANGER! Disconnect from the mains before starting any maintenance work.

The front objective lens should be cleaned weekly using a soft lint-free cloth moistened with glass cleaning fluid. Do not use alcohol or solvents.
Clean the cooling fans monthly.
The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air-jet. Remove dust and dirt from the fans and cooling vents using a soft brush and vacuum cleaner.
Check the air filters periodically and clean them before they become clogged.
There are two air filters placed in the fixture’s covers and two in the fixture base. They can be cleaned using a vacuum cleaner, compressed air, or by washing them and letting them dry.
After replacing the air filters, reset the elapsed time counter in the menu Information (Information > Air Filters > Elapsed Time).

Replacing the Fuse:
Before replacing the fuse, unplug the mains lead.

Remove the fuse holder on the rear panel of the base with a fitting screwdriver from the housing (anticlockwise).
Remove the old fuse from the fuse holder.
Install the new fuse in the fuse holder (only use the same type and rating).
Replace the fuse holder in the housing and fix it.

Warranty Information:

All LED Products from JMAZ Lighting have a 2-year limited manufacturer’s warranty from defects.
Any non-LED Product from JMAZ Lighting have a 1-year limited manufacturer’s warranty from defects.
Batteries that come included with a JMAZ Lighting product have a limited 6-month manufacturer’s warranty from defects.
Discharge bulbs that some products use, instead of LED, have a 6-month limited manufacturer’s warranty from defects.

USER MANUAL

Be sure to read the USER MANUAL carefully before using this product.
Be sure to keep the USER MANUAL properly for future needs.
Use this product correctly when you can fully understand the User Manual

Safety instructions

Thank you for choosing our ATTCO BEAM 230. For your own safety, please read this user manual carefully

BEFORE YOUR INITIAL START-UP

CAUTION!

Be careful with your operations.
With a high voltage, you can suffer a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.

CAUTION!

Keep this device away from rain and moisture!
Unplug the mains lead before opening the housing!

Important:

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
During the operation the housing becomes hot). Allow the fixture to cool for approximately 20 minutes prior to manipulating it.
Make sure that the available voltage is not higher than stated on the rear panel.
WARNING! This unit does not contain an ON/OFF switch. Always disconnect the power input cable to completely remove power from the unit when not in use or before cleaning or servicing the fixture.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the power cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to the earth.
The electric connection, repairs, and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
During the initial start-up, some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective.
Do not touch the device’s housing with bare hands during its operation (the housing becomes hot)!
For replacement use lamps and fuses of the same type and rating only.

CAUTION! EYE DAMAGES!

Avoid looking directly into the light source (meant especially for epileptics)!

Maintenance and cleaning

It is absolutely essential that the fixture is kept clean and that dust, dirt, and smoke-fluid residues must not build upon or within the fixture. Otherwise, the fixture’s light output will be significantly reduced. Regular cleaning will not only ensure the maximum light output but will also allow the fixture to function reliably throughout its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances should alcohol or solvents be used!

DANGER!
Disconnect from the mains before starting any maintenance work

The front objective lens will require weekly cleaning as smoke-fluid tends to build up residues, reducing the light output very quickly. The cooling fans should be cleaned monthly.
The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air-jet. Remove dust and dirt from the fans and cooling vents using a soft brush and vacuum cleaner.
Important! Check the air filters periodically and clean them before they become clogged!
Clean two air filters placed in the fixture’s covers and two in the fixture base. Use a vacuum cleaner or compressed air or you can wash them and put them back dry.
After replacing the air filters, reset the elapsed time counter in the menu “Information” (information —>Air Filters—>Elapsed Time).

Replacing the fuse. Before replacing the fuse, unplug the main lead.

Remove the fuse holder on the rear panel of the base with a fitting screwdriver from the housing (anti-clockwise).
Remove the old fuse from the fuse holder.
Install the new fuse in the fuse holder (only the same type and rating).
Replace the fuse holder in the housing and fix it.

Important Warranty Information:

All LED Products from JMAZ Lighting have a 2-year limited manufacturer’s warranty from defects.
Any non-LED Product from JMAZ Lighting has a 1-year limited manufacturer’s warranty from defects.

Batteries and Discharge Bulbs

Any batteries that come included with a JMAZ Lighting product have a limited 6-month manufacturer’s warranty from defects.
Discharge bulbs that some products use, instead of LED, have a 6-month limited manufacturer’s warranty or up to 2,000 hours of run time for the bulb. Whichever occurs first.

9| 9| 0-255| ln(near) to Out(far)

Rotating prism 1

Prism 1 swing out(hole) Prism 1 swing in

---|---|---|---
10| 10|
| | 0-5
| | 6-127
128-189| Prism 1 Forwards rotation from fast to slow
| | 190-193| Prism 1 rotation stop

Prism 1 Backwards rotation from slow to fast

Rotating prism 2

Prism 2 swing out(hole)

| | 194-255
11| 11|
| | 0-5
6-127| Prism 2 swing in
128-189| Prism 2 Forwards rotation from fast to slow Prism 2 rotation stop

Prism 2 Backwards rotation from slow to fast

UNPACKING

The ATTCO beam 230 adopts a 231 W lamp which features high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation. Please check whether the following items are included inside the box:

The ATTCO BEAM 230 is made of a new type of high-temperature strength of engineering plastics and cast aluminum casing with a nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with the international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. And it is applicable for large-scale live performances, theater, studios, nightclubs, and discos.
This manual covers important information on installation and applications. Meanwhile, please keep this manual well for future needs.

TECHNICAL INFORMATION

SPECIFICATIONS:

1X OS RAM ‘slRIUS HRI 231W Lamp
2000 Hours rated lamp source
Input voltage:AC90-260V 50/60Hz
Power consumption: 310W
- Control signal:DMX512, master-slave and sound activated or auto operation (8 built-inprograms)
Control channel:14/16 DMX channels USITT DMX-512
Dimensions: 12″x 8.8″x 17″ /30. 722.443.5cm
Packing dimensions:17″x 1 0″x 20″ /4426.551.5cm
Net weight:28.16 lbs / 12.8kgs
Gross weight: 34 lbs / 15.6kgs

FEATURES:

2.5° Beam angle
Anti-reflection 136mm front lenses
Motorized focus from near to far(2.5M-30M)
Dual prism wheel,8-facet prism+24-facet prism with variable speed
8 Built-in lighting shows
Built-in wireless DMX technology
Frost filter available (Hybrid effect for wash)
Dual flag mechanical dimming system
20T/sec high speed LED shutter/strobe effect with variable speed
Preset variable/random strobe and dimming pulse effect
2.4′ TFT LCD display (320*240pix)
Display reversible for up side down application
Powercon IN/OUT
3-Pin XLR connectors IN/OUT
Lamp using time readable on the display
IP20 protection rating
55dB at 3’dB rating
2*1/4 turn fastening Omega clamps
1 *Sa fety attachment point available
MOVEMENT :
Smooth and precise resolution for PAN/TILT movement 630° /540° /360° PAN and 270°/180° /90° TILT movement optional
Scan position memory, auto reposition after unexpected movement

COLORS:

1 Color wheel with 11 colors plus open. GOBOS:
1 Static gobo wheel with 16 gobos plus open

FUNCTION :

Electronic ballast and power supply
Improved optics and flat beam field
No need for adjustment of reflector or lamp
Variable direction rainbow effect with speed adjustable
Vector mode with blackout MIB function
Constant temperature readout and management function
Fan cooling system
35-45°C max ambient temperature

15-19

20-24

25-29

| gobo3

gobo4 gobo5

---|---
30-34| gobo6
35-39

40-44

45-49

50-54

| gobo7 gobo8 gobo9

gobo10

55-59| gobo11
60-64

65-69

70-74

75-79

| gobo12 gobo13 gobo14

gobo15

80-84| gobo16
85-92

93-100

101-107

108-116

| Gobo1 shake slow to fast Gobo2 shake slow to fast Gobo3 shake slow to fast

Gobo4 shake slow to fast

117-124| Gobo5 shake slow to fast
125-132

133-140

141-148

149-156

| Gobo6 shake slow to fast Gobo7 shake slow to fast Gobo8 shake slow to fast

Gobo9 shake slow to fast

157-164| Gobo10 shake slow to fast
165-172

173-180

181-188

189-196

| Gobo11 shake slow to fast Gobo12 shake slow to fast Gobo13 shake slow to fast

Gobo14 shake slow to fast

197-204| Gobo15 shake slow to fast

| 205-212

213-255

| Gobo16 shake slow to fast

Rot. gobo wheel cont. rotation slow to fast

Shutter

0-31| Shutter closed
32-63| Shutter open
64-95

96-127

128-143

| Strobe e ffect slow to fast Shutter open

Opening pulse in sequences slow to fast

144-159| Closing pulse in sequences fast to slow
160-191| Shutter open

| 192-223

224-255

| Random strobe e ffect slow to fast Shutter open

Dimmer

0-255| Dimmer0% …100%
9| 9| | Focus

DMX PROTOCOL

Mode/Channel

Standard Vector 1 1

| Values| Function Pan
---|---|---

| ****

| 0-255

0-255

| PAN Movement

Pan-fine

Fine control of Pan movement

Tilt

3| 3
| 0-255| Till Movement
4| 4| ****

0-255

| Tile-fine

Fine control of Tilt movement

Color wheel

5| 5
| 0-4| Open/white
| 5-9| White+Color 1
| 10-14

15-19

20-24

| Color 1 Color 1+Color 2

Color2

| 25-29| Color 2+Color 3
| 30-34| Color 3
| 35-39

40-44

45-49

| Color 3+Color 4 Color 4

Color 4+Color 5

| 50-54| Color 5
| 55-59

60-64

65-69

70-74

| Color 5+Color 6 Color 6

Color 6+Color 7

Color?

| 75-79| Color?+Color 8
| 80-84

85-89

90-94

95-99

100-104

| Colors Color B+Color 9

Color 9 Color 9+Color 10

Color 10

| 105-109

110-114

115-127

128-189

| Color 10+Color 11 Color 11

Color 11+White

Forwards rainbow effect from fast to slow

| 190-193| Color ratation stop

| ****

| 194-255

0-4

5-9

| Backwards rainbow effect from slow to fast

Gobo Wheel 1

Ooen aobo1

| 10-14| oobo 2

PHOTOMETRICS DIAGRAM

OPERATION INSTRUCTIONS

The ATTCO BEAM 230 is for beam effect for on-site decoration purposes.
Don’t turn on the fixture if it’s been through severe temperature differences like after transportation because it might damage the light due to the environmental changes. So make sure to operate the fixture until it is in normal temperature.
This light should be kept away from strong shaking during any transportation or movement.
Don’t pull up the light by only the head, or it might cause damage to the mechanical parts.
Don’t expose the fixture in overheat, moisture, or environment with too much dust when installing it. And
don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
Make sure the installation place is in good safe condition before installing the fixture.
Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture.
Make sure the lenses are in good condition. It’s recommended to replace the units if there are any damages or severe scratches.
Make sure the fixture is operated by qualified personnel who know the fixture before using it.
Keep the original packages if any second shipment is needed.
Don’t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies.
It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation, like shock short circuit, electronic shock , lamp broke, etc.

INSTALLATIONS

Cautions:

For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture. from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails.

Mounting points:

Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.

Clamp Mounting:

ATTCO HYBRID 230 provides a unique mounting bracket assembly that integrates the bottom of the base, and the safety cable rigging point in one unit (see the illustration below). When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the “Hanging Kit”. As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly .

Description of the Wireless Indicator for Wireless DMX

Under the Set-up mode, each color on the indicator means different communication protocols:
Red —————–Wi-MAZ Protocol
Yellow————-(Generic) Protocol
Under the Operation mode, explanation of the indicator’s status:

Operation Guide for the Wireless DMX

How to Set up the Wireless DMX Mode:
Turn the power switch to off on the back of the light, press and hold the “SELECT” button then turn the power switch to ON. When you see the status indicator turn into the white color, release the button to enter the Set-up mode. In this mode, you can select different transmission protocols. Each time you press the “SELECT” button, you will see the status indicator changes in the following order: red, green, blue, and yellow. Choose one of the protocols (recommended using RED- Wi-MAZ protocol), then press and hold the “SELECT” button for two seconds, When you see the indicator light turn to white color, release the “SELECT” button and it will enter the operation mode, the set up for wireless DMX is done.

Under the Wi-MAZ protocol or Generic protocol, you can select different DMX Groups:

Press the “SELECT” button once, it will indicate the current DMX group. Press the “SELECT” button twice, you can switch over to a different DMX group.

Explanation of the DMX Signal setting on the menu

CONTROL CONNECTION

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple Moving heads together through serial linking. The cable needed should be a two-core, screened cable with XLR input and output connectors. Please refer to the diagram below. DMX-512 connection with DMX terminator.
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a3 resistor connected between pins 2 and 3, which is then plugged into the output XLR socket of the last fixture in the chain. Please see the illustrations below.

Display flip function: Press the UP and Down buttons simultaneously for three seconds,and the display direction is reversed.

References

Home - JMAZ

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual >>