ACTIA 103250101 Telematics Device User Manual
- June 5, 2024
- ACTIA
Table of Contents
103250101 Telematics Device
User Manual
Copyright © 2018 ACTIA NORDIC AB
ACTIA Nordic AB SWEDEN info@actia.sewww.actia.se
1. CONTENTS
2. INTRODUCTION
This document describes how to set up the 103250101 for certification testing.
2.1 REVISION HISTORY
2.2 ABBREVIATIONS
| Abbreviation | Meaning |
|---|---|
| GNSS | Global Navigation Satellite System |
| QZSS | Quasi-Zenith Satellite System |
| OTA | Over The Air |
| CAN | Controller Area Network |
2.3 REFERENCES
| Reference | Title | Doc. number | Revision |
|---|---|---|---|
3. OVERVIEW
3.1 CONNECTORS
Following connectors are available on the 103250101:
103250101 has four external connectors:
- 8-pin connector Power supply, CAN and I/O.
- Blue FAKRA Antenna connection for GNSS antenna.
- Violet FAKRA Antenna connection for main LTE antenna.
- 6-pin connector Analog inputs. Also test interface is available after modification of unit.
3.1.1 8-pin MQS connector
This connector is used for power supply, CAN bus, input- and output signals.
3.1.2 GNSS Antenna
The blue FAKRA connector is input for GNSS antenna.
3.1.3 Cellular Antenna
The violet FAKRA is the main antenna interface for 2G/3G/4G communication.
3.1.4 6-pin MQS connector
This connector is used for input signals.
3.2 POWER SUPPLY
The 103250101 is designed to be powered by an external vehicle battery.
Nominal supply voltages are 12, 24, 36, 48 V (depending on vehicle). The power
supply range is 8-60V.
3.3 SIM INTERFACE
The embedded modem can use an embedded SIM chip as a SIM source.
3.4 EXTERNAL ANTENNA
103250101 is certified to be used with an external roof mounted antenna.
3.5 RF PARAMETERS
3.5.1 Supported bands and output power
3.6 GNSS
GNSS antenna input is the blue FAKRA connector.
3.6.1 Supported bands
| Technology | Bands |
|---|---|
| GPS | L1 |
| GLONASS | L1 FDMA |
| Galileo | E1 |
| BeiDou (COMPAS) | B1, B1-2 |
| QZSS | L1 |
4. MECHANICAL DESIGN
Figure 2 103250101 mechanical design
5. FUNCTIONAL DESCRIPTION
The following functions are available in the 103250101:
- Allow log on and start a working pass. In some cases, the driver will need to perform a Pre-Operational check by answering questions that are handled by the 103250101 before starting the working pass.
- Gather information and send various reports from the truck including truck status, battery data, working pass data, collision reports etc. to the manufacturer server.
- Send configurations to the 103250101 for setting of the various options.
- Send truck immobilize command.
- Retrieve diagnostic data using the TruckCom diagnostics tool.
- Update software over CAN or OTA.
- Gather GNSS data and get geofencing notifications.
- Report issues with the truck.
- Immobilize the truck when it has received a shock (crash).
6. INSTALLATION AND MAINTENANCE
6.1 INSTALLATION
The product is factory fitted in trucks. It is not possible to buy this
product separately.
Please be aware that the antenna must be installed to provide a separation
distance of at least 20cm from all persons.
6.2 MAINTENANCE
The status of the product can be read via diagnostic connections using special
workshop tools. In addition, other ECUs monitor the communication from the
product and in case of missing/invalid communication, the Central Electronic
Module in the truck is alerted, and will display a warning to the driver.
Maintenance and replacement of the product can only be performed by certified workshops.
7. REGULATORY CERTIFICATIONS
7.1 USA (FCC)
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
7.1.1 FCC Warnings and Notices
WARNING: The FCC requires the user to be notified that any changes or
modifications made to this device that are not expressly approved by Actia
Nordic AB could void the user’s authority to operate the equipment.
RF EXPOSURE WARNING: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
7.1.2 OEM Requirements
Following text should be printed in the user manual for vehicles in US:
Type Approval USA
FCC ID: 2AGKK103250101
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>