Dimplex WTN20-AU Winston Suite Electric Fireplace Instruction Manual
- June 5, 2024
- Dimplex
Table of Contents
Dimplex WTN20-AU Winston Suite Electric Fireplace
INSTRUCTION
Important Safety Advice
When using electrical appliances, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: If the appliance is damaged, check immediately with the supplier before installation and operation. Do not use this appliance in the immediate surroundings of a bath, shower or swimming pool. Do not use outdoors. Do not use this heater if it has been dropped. Do not use this heater if there are visible signs of damage Use this heater on a horizontal and stable surface. This appliance must not be located immediately above or below a fixed socket outlet or connection box.
WARNING: The appliance carries the Warning Symbol indicating that it must not
be covered or has a Do not cover label. Do not cover or obstruct in any way
the heat outlet grille located above the flame window on the appliance
Overheating will result if the appliance is accidentally covered. Do not place
material or garments on the appliance, or obstruct the air circulation around
the appliance, for instance by curtains or furniture, as this could cause
overheating and a fire risk. In the event of a fault unplug the heater. Unplug
the appliance when not required for long periods.The supply cord must be
placed on the right hand side of the heater away from the heat outlet
underneath the appliance.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Cleaning and
user maintenance shall not be made by Children. Children shall not turn on/off
the appliance. The appliance must be positioned so that the plug is
accessible. Although this appliance complies with safety standards, we do not
recommend its use on deep pile carpets or on long hair type of rugs. If the
supply cord is damaged it must be replaced by the manufacturer or service
agent or similarly qualified person in order to avoid a hazard.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility. Some parts of this product can become very
hot and cause burns. Particular attention has to be given where children and
vulnerable people are present.
Technical Information
General
Unpack the heater carefully and retain the packaging for possible future use,
in the event of moving or returning the fire to your supplier.
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the year.
Using the flame effect on its own only requires little electricity.
Before connecting the heater check that the supply voltage is the same as that
stated on the heater. Please note: Used in an environment where background
noise is very low, it may be possible to hear a sound which is related to the
operation of the flame effect. This is normal and should not be a cause for
concern.
Electrical Connection
WARNING: THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage marked on the
heater must correspond to the supply voltage. Before switching on, please read
the safety warnings and operating instructions.
Controls
User Modes:
Remote Control
The maximum range of use is ~ 5metres.
NOTE: It takes time for the receiver to respond to the transmitter.
NOTE: The reciever for the remote control is located in the display, aim the
remote control in this direction when inputting commands.
Do not press the buttons more than once within two seconds for correct
operation.
Battery Information
- To activate the remote control remove the clear battery isolation strip at the base of the remote control, which is used to ensure your remote control reaches you fully charged.
- To replace the remote control battery, turn over the remote control, and follow the diagram embossed on the remote control
- Only use CR2025 or CR2032 size of batteries.
WARNING – KEEP BATTERIES OUT OF REACH OF CHILDREN
- Swallowing may lead to serious injury in as little as 2 hours or death, due to the chemical burns and potential perforation of the oesophagus.
- If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons Inforation Centre on 13 11 26 (in Australia) or 0800 764 766 (in New Zealand) for fast, expert advice.
- Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if the compartment is not secure.
- Dispose of used button batteries immediately and safely. flat batteries can still be dangerous.
WARNING: THE APPLIANCE IS PROVIDED WITH A TIPPING RESTRAINT, THIS RESTRAINT IS NOT A SUBSTITUTE FOR PROPER ADULT SUPERVISION. THIS RESTRAINT MAY PROVIDE PROTECTION AGAINST TIPPING FURNITURE. DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE. FAILURE TO DETACH THIS RESTRAINT BEFORE MOVING FURNITURE MAY RESULT IN INJURY AND DAMAGE.This product is provided with a ‘Tipping Restraint Kit’ as shown in, to prevent the product accidentally tipping. Instructions are supplied with this kit please follow these instructions carefully. This accessory is intended to improve the safety of the product.
Corner Unit Assembly
NOTE: will not appear if it is not applicable.
Some of our suites are designed to be used in a corner in which cases the
suite will require some assembly, please follow the following steps
- Assemble the top of the mantel to the rear support using the supplied hardware.
- Using the supplied hardware assemble the top and rear support assembly to the main fireplace body .
Thermal Safety Cut-out
The built-in overheat cut-out, switches off the appliance automatically in the
event of a fault! Should this occur switch off the appliance or disconnect the
mains plug from the socket.
Remove any obstructions which may have caused the overheating. After a short
cooling down phase, the appliance is ready for use again! If the fault should
occur again, contact your local dealer!
WARNING: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
Light Emitting Diode
This fire is fitted with LED (Light Emitting Diode) lamps. These LED lamps are
maintenance-free and should not require replacing during the life of the
product.
Cleaning
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive cleaners.
The glass viewing screen should be cleaned carefully with a soft cloth.
DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush attachment of a
vacuum cleaner should occasionally be used to clean the outlet grille of the
fan heater. WARNING: do not operate the product without the grille and outer
glass in position as this may effect the operation of the heater.
Recycling
At the end of the electrical product’s useful life it should not be disposed
of with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice in your country.
After Sales Service
Should you require after sales service or should you need to purchase any
spares, please contact the retailer from whom the appliance was purchased or
contact the service number relevant to your country on the warranty card.
Please do not return a faulty product to us in the first instance as this may
result in loss or damage and delay in providing you with a satisfactory
service. Please retain your receipt as proof of purchase.