electriQ eiQCURV60SCTOUCH 60cm Curved Glass Touch Control Chimney Cooker Hood User Manual

electriQ eiQCURV60SCTOUCH 60cm Curved Glass Touch Control Chimney Cooker

Hood

IMPORTANT SAFETY INFORMATION

Please read this instruction manual carefully and retain for future reference. It contains important information concerning the safe operation, installation and maintenance of the appliance.

• There must be adequate ventilation of the room when the hood is used at the same time as appliances burning gas or other fuels.
• This cooker hood is only designed for domestic use, and should not be used in a commercial environment.
• Never use the hood for any purpose other than its intended use.
• Do not check the status of the filters during operation of the cooker hood.
• Do not touch the light bulb within 30 minutes of use.
• Do not flambé or excessively flame under the hood.
• Never leave frying food unattended as it can be a serious fire hazard.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.
• The socket outlet for the hood must be located so it is easily accessible for the user after installation.
• Ensure the mains supply voltage corresponds with that of the appliance.
• There is a fire risk if cleaning is not carried out in accordance with the instructions.
• Ensure that the socket used provides adequate earthing of the appliance, if unsure professional advice must be sought.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children must not play with the appliance.
• Cleaning and user maintenance must not be carried out by children without supervision.
• When the hood is being maintained, cleaned or filters changed, make sure it is switched off at the mains supply.
• The exterior of the hood should be cleaned with mild detergent on a warm damp sponge or cloth.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
• Regulations concerning the discharge of air have to be fulfilled.
• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the hood must be at least 65 cm.
• When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.
• Failure to install the hood in accordance with these instructions may result in electrical hazards.

CAUTION:
Accessible parts may become hot when used with cooking appliances.
Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames

PARTS

INSTALLATION DIAGRAM

OPTIONS FOR VENTILATION

This hood can be set up for either external venting or recirculation of the air. The type of setup should be decided before commencing installation.

EXTERNAL VENTING
If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using the flexible exhaust pipe (NOT SUPPLIED). Alternatively, any suitable extraction duct (enamel, aluminium, flexible pipe or inflammable material with an interior diameter of 150mm) can be used.
An adaptor is also supplied to enable you to connect your hood to pre-existing 120mm diameter ducting. If this is the chosen installation method consideration to the route of the vent pipe should be made prior to installation.
Please note: the performance of the hood may be affected if the diameter of the pipe is reduced, or if the airflow is restricted.

RECIRCULATION
This cooker hood also supports the recirculation of air once it has passed through the filters. The filtered air is then expelled through the vent holes in the side of the chimney.
When setting the unit up in this configuration, carbon filters should also be used to remove odours from the air. Details of sourcing and fitting the filters can be found in the carbon filter section of this manual.

INSTALLATION

BEFORE INSTALLING YOUR HOOD:

• Unpack the hood and check that all functions are working. Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency at the installation site.
• Check that the area behind the installation surface to be drilled is clear of any electrical cables or pipes, etc.
• The surfaces of the hood are very easily damaged during installation if grazed or knocked by tools. Please take care to protect the surfaces during installation.
• Protect the hob surface with cardboard, or similar, to prevent damage occurring whilst the hood is being installed above.
• The manufacturer shall not be liable for any failure to observe all safety regulations in force for the correct and normal operation of electrical products.
• Ensure the wall is level and the installation plates are horizontal to prevent grease from accumulating within the hood.
• Ensure the power has been turned off at the mains before starting installation.
• Connection to the mains supply must be in an accessible location.
• You may need the following tools to complete this installation:
  • Drill appropriate for your wall
  • Phillips Screwdriver
  • Tape Measure
  • Hand Saw or Jig Saw
• Electrical wiring must be done by a qualified person in accordance with all applicable codes and standards, including fire rated construction.

INFORMATION

• Sufficient air is needed for proper combustion and exhaustion of gases through the flue (chimney) for fuel burning equipment to prevent back drafting. Ductless fans must always be vented to the outdoors.
• When assessing the air pressure, the entire ventilation system in the house/apartment must be considered.
• All legal regulations must be observed for the conveyance of exhaust air. If the extractor hood is used in recirculating mode with the optional carbon filter, there are no operating restrictions.

1. Before installation, ensure you have not connected the appliance to the mains supply.

2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect.

3. Drill all 7 holes for the hood using the installation diagram as a guide. Use the supplied screws (ST5 x 50mm) to attach the hood installation plate, and the Upper chimney bracket to the wall in the correct position, ensuring the plates are level.

4. The 2 air flaps should now be installed on the top of the unit, as access is easier before the unit is wall mounted. The flaps should be carefully installed, bending them slightly so the lugs at each end locate into the holes in the outlet vent. When the unit is in operation the flaps pivot upwards to allow airflow.
   Please note: Ensure the small lugs at each end of each flap locate into the holes on the housing and not the grooves above them.

5. Slide the chimney sections onto the hood. Fix the base of the lower chimney section to the hood using two ST4.2 x 9.5mm screws (supplied)

6. Fix the lower chimney bracket to the top of the lower chimney using two ST4.2 x 9.5 screws (supplied).

7. Hang the hood on the Installation plate, and secure to the wall using two screws
   (ST5*50) through the lower chimney bracket into the wall plugs previously inserted.

8. If the hood it to be vented externally, push an exhaust pipe onto the top of the hood, and route it externally.

9. Slide the inner chimney up to the correct height and fix into position on the upper chimney bracket using the remaining two screws (ST4.2*9.5).

OPERATION

| POWER BUTTON – Allows the hood to be turned on and off.

Please note: When turning off the fan, it will enter a 3- minute delay to ensure all vapours and/or odours are removed. During this the power indicator will flash. To turn the hood off immediately during this time, press the power button again.

| INCREASE SPEED BUTTON – Press to increase the fan speed. The current fan speed is displayed on the panel.

1 – Low, 2 – Medium, 3 – High

****| DECREASE SPEED BUTTON – Press to decrease the fan speed. The current fan speed is displayed on the panel.

1 – Low, 2 – Medium, 3 – High

****| LAMP BUTTON – Turns the lights on the underside of the hood on and off

REPLACING THE BULB

This hood is fitted with an LED light unit, which under normal operation can last the lifetime of the hood. In the event that it does fail, replacement light units are available from the same retailer the hood was purchased from.
Before changing the fitting, ensure the hood is turned off and the power is removed by either unplugging the unit or switching off at the pole switch (if installed) before attempting to change the bulb. Wait until the bulb has cooled down before commencing replacement.

1. Remove the glass canopy from the top of the hood, following the Removal and refitting of the glass canopy section.

2. Locate the top of the light fitting and squeeze the spring clips, while pushing the fitting out of the base of the hood.

3. Follow the wire from the light unit and find the power connector on the lead.

4. Disconnect the power connector from it, ensuring the light fitting is not allowed to fall from the unit

5. Replace with a new light unit, which after connecting the electrical connection, should be pushed into position on the base of the hood.

6. Refit the glass canopy.
   Important

   • If a bulb is found to be defective, it should be replaced immediately.
   • Always switch off the electricity supply before carrying out any operations on the appliance. When handling the bulb, make sure it has completely cooled down before any direct contact to hands.

INSTALLING THE CARBON FILTER (OPTIONAL)

1. Remove the grease filters from the underside of the hood.
2. The carbon filters are located at either end of the motor.
   TO FIT: Locate the filter on the peg on the side of the motor. Rotate the filter clockwise onto the motor housing;
   TO REMOVE: Rotate the filter anti-clockwise until it is unscrewed . Warning: The carbon filter cannot be washed or recycled. It should be replaced after approximately 2-3 months of use.
   When the activated carbon filters are attached, the suction power will be reduced.
   Note: The optional carbon filter is available from the hood supplier/manufacturer under the following stock code: eiQMIDCARBON

REMOVAL AND REFITTING OF THE GLASS CANOPY

WARNING: Components within the appliance may have sharp edges. When attempting to remove or refit the glass, gloves should be worn to avoid scratches and cuts.

The glass canopy is held into position using four screws, spacers and decorative washers. Remove the four screws, spacers and decorative washers from the glass canopy, ensuring the canopy is suitably supported. Two people should then lift the canopy off the hood, retaining the fittings removed for re fitting. Refitting is the reverse of removal. Before refitting the hood, please ensure the decorative trim is correctly located, and has not become detached or displaced during disassembly.

CLEANING AND MAINTENANCE

Disconnect range hood from power supply before cleaning or servicing.

1. Clean the hood surface frequently using mild detergent and a warm damp sponge or cloth.
2. Do not use harsh alkalis or abrasives.
3. Avoid the use of scouring powers or dishwasher compounds.
4. If the optional carbon filter is being used, these cannot be cleaned and require replacing every 2-3 months depending on frequency of use. They are available from the retailer who supplied your hood.

Information
Cleaning water must be kept away from the motor, control switch and all electrical components.

GREASE FILTERS

It is recommended that the grease filter is cleaned every two to three months by carrying out the following instruction:

1. Remove the grease filter from the cooker hood and wash it in a solution of warm water and neutral liquid detergent, leaving to soak.
2. Rinse thoroughly with warm water and allow to dry thoroughly before refitting.
3. The metallic filter may alter in colour after several washes.

There is a fire risk if cleaning is not carried out in accordance with the instructions.
Replacement grease filters are available under the following codes:

TROUBLESHOOTING

Light on, but fan does not work

| The fan blade is jammed.| ****

Switch off the unit. Repair to be carried out by qualified service personnel only.

The motor is damaged.
Both light and fan do not work| Power cord loose| Plug in to the power supply again.

Excessive Vibration

| ****

The fan blade is damaged.

| Switch off the unit. Repair to be carried out by qualified service personnel only.

The fan motor is not fixed tightly.

| Switch off the unit. Repair to be carried out by qualified service personnel only.
The unit is not hung properly on the bracket.| Take down the unit and check whether the bracket is in proper location.

Suction performance not good

| 1.   Grease filters clogged

2.   Distance between the unit and the cooking plane too great.

| 1      Clean or replace grease filters.

2      Adjust the distance to between 70cm and 80cm.

SPECIFICATION

The following shows how to reduce total environmental impact (e.g. energy use) of the cooking process).

1. Install the cooker hood in a proper place where there is efficient ventilation.
2. Clean the cooker hood regularly so as not to block the airway.
3. Remember to switch off the cooker hood light after cooking.
4. Remember to switch off the cooker hood after cooking.

MANUFACTURER SUPPORT

www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA
Telephone: 0330 390 3061
Office Hours: 9:00am to 5:00pm Monday to Friday

ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

INFORMATION FOR DISMANTLING

Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with your Local Authority or retailer for recycling advice.

ENERGY EFFICIENCY INFORMATION FOR DOMESTIC RANGE HOODS

Model Identification

| eiQCURV60SCTOUCH eiQCURV60BLTOUCH eiQCURV90SCTOUCH eiQCURV90BLTOUCH
---|---
 | Symbol| Value| Unit
Annual Energy Consumption| AEChood| 53.2| kWh/A
Standard Annual Energy

Consumption

| ****

SAEChood

| ****

65.0

| kWh/a
Time increase factor| F| 1.6|
Fluid Dynamic Efficiency| FDEhood| 11.0|
Energy Efficiency Index| EEIhood| 81.8|
Measured air flow rate at

best efficiency point

| ****

QBEP

| ****

244.2

| m3/h
Measured air pressure at

best efficiency point

| ****

PBEP

| ****

142

| Pa
Maximum air flow| Qmax| 423.6| m3/h
Measured electric power

input at best efficiency point

| ****

WBEP

| ****

87.4

| W
Nominal power of the

lighting system

| ****

WL

| ****

1.5W x 2

| W
Measured power of the

lighting system

| ****

WL

| ****

3.0

| W
Measured value of the

Lighting Efficiency

| ****

LEhood

| ****

59

| Lux/W
Average illumination of the lighting system on the

cooking surface

| ****

Emiddle

| ****

177

| ****

lux

Measured power consumption in standby

mode

| ****

Ps

| ****

0.49

| ****

W

Measured power

consumption off mode

| ****

Po

| ****

—

| W
Tested according to EN 50564:2011

Sound power level

| ****

LWA

| Minimum speed:57 Maximum

speed: 65

| ****

dB

Tested according to EN 60704-2-13:2011, EN 60704-1:2010 + A11:2012

References

• Buy electriQ Appliances Online | TVs | Ovens | Dehumidifiers | Security

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>