Dudian CT220X Label Printer Installation Guide
- June 5, 2024
- Dudian
Table of Contents
Dudian CT220X Label Printer
Installation Guide
CT220X
QUICK INSTALLATION GUIDE
Shenzhen Dudian Technology Co., Ltd.
Room 1101, Building 3, COFCO Chuangzhi Factory Area, District 67,
Xingdong Community, Xin’an Street, Baoan District, Shenzhen.
UNPACKING CHECKLIST
APPEARANCE COMPONENT
- “I ” means that the printer is started;
- “0” means that the printer is closed.
- Connect the round-hole power cord.
- Connect to the computer for printing.
- Connect to the cashbox.
INSTALLATION OF CONSUMABLES
-
Make sure that the printer is powered on and started up.
-
Press the uncovering button down with your thumb, to open the paper case cover.
-
Take the label shaft and baffle out, and slip the roll over the label shaft.
Install roll set into the printer from top to bottom -
Place the label paper at right position.
-
Close the paper case cover.
**** When the register paper is printed, take the label shaft and baffle out, directly put into paper case, and follow steps 4~5.
KEY FUNCTION
Label mode
| Preconditions | Power switch | Paper advance button | Function description |
|---|---|---|---|
| Nil | Turn to I | – | Startup |
| Nil | Turn to 0 | – | Shutdown |
| Being printed | – | Click | Printing suspended |
| Printing suspended | – | Click | Printing proceeded |
| Ready | – | Click | One piece of paper advanced |
| Ready | – | Keep pressing for2 seconds | Paper test |
| Ready | – | Double-click | Printing self-inspection page |
| The machine is turned off | Then, turn to I | Firstly hold | Switch label/bill |
mode
Bill mode
| Preconditions | Power switch | Paper advance button | Function description |
|---|---|---|---|
| Nil | Turn to I | – | Startup |
| Nil | Turn to 0 | – | Shutdown |
| Ready | – | Click | 10 mm paper advance |
| Ready | – | Keep pressing | Continuous paper advance, stop immediately upon |
release.
Ready| –| Double-click| Printing self-inspection page
The machine is turned off| Then, turn to I| Firstly hold| Switch label/bill
mode
DESCRIPTION OF INDICATOR LIGHTS
Standard version
| Blue | Red | Indication status |
|---|---|---|
| Normally on | Quick flashing | Off |
| Quick flashing | Off | Over-temperature protection |
| Off | Normally on | Top cover opened/shortage of paper case |
Bluetooth version
| Blue | Red | Indication status |
|---|---|---|
| Slow flash | Off | Bluetooth unconnected |
| Normally on | Off | Bluetooth connected |
| Quick flashing | Off | Over-temperature protection |
| Off | Normally on | Top cover opened/shortage of paper case |
**** Indicator lights will slightly vary between different versions of the printer.
SOFTWARE DOWNLOAD
iOS / Android
Scan the QR code below with a mobile phone to download”Clabel trade”.
https://yunprint.dlabel.cn/app/downcode.html
Please operate the software following the software guidance.
Clabel trade
Download the label editing app “Clabel trade” from Google Play Store or Apple
App Store and install it.
Window
Visit https://ga.ctaiot.com/pc Download” Clabel trade” and driver. Please
check the software used in the software help center
PRECAUTIONS
Precautions for use of the printer
- The printer shall be installed at a steady location, away from vibration and impact.
- DO NOT use or store the printer at any place with high temperature, high humidity or serious contamination.
- Connect the power adapter of the printer to an appropriate grounding socket. DO NOT share the same socket with a large motor or other equipment that may lead to voltage fluctuation of the power supply.
- Strictly prevent water or conductive substances (i.e. metal) from entering the printer. In case of any invasion, immediately shut off the power supply.
- The printer must not work without paper,otherwise, roller and thermo-sensitive print head may be seriously damaged.
- Please shut off the power adapter if the printer will not be used for a long term
- The user must not disassemble the printer for maintenance or modification without authorization.
- Only the power adapter delivered together with the printer can be used.
- To ensure the printing quality and product life,it is advised to use high-quality paper.
- Please assure that the printer is powered off, before plugging/ unplugging the connecting wire.
- The power plug of the adapter is the power disconnection device. Its socket shall be installed nearby the equipment and easy to be accessed.
- This product is applicable to tropical climatic conditions no higher than 5,000 above sea level only.
Printer cleaning
Under any of the following circumstances, the print head shall be promptly cleaned:
- Printing is not clear.
- Some column on the printed page is unclear.
- It is noisy in the course of paper feeding.
Cleaning steps for the print head are as follows:
- Turn off the power supply, open the top cover and remove the paper if any.
- If the printing is just finished, wait until the print head is cooled completely.
- Remove dust and dirt on the surface of a thermo-sensitive sheet of the print head with soft cotton cloth with ethanol absolute (wrung out).
- After complete volatilization of ethanol absolute, close the top cover and re-commission for printing
Cautions
- Before routine maintenance, you must ensure that the printer is powered off.
- DO NOT touch the surface of the print head with your hand or metal. DO NOT use tweezers or such tools to scratch the surface of the print head, roller, and sensor.
- DO NOT use gasoline, acetone or such organic solvent.
- After complete volatilization of ethanol absolute, turn on the power and proceed with printing.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority tooperate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interferencewill does not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment to an outlet on a circuit different. from that to which
the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
NOTE: This device and its antenna(s) must not be co-located or operated
in conjunction with any other antenna or transmitter.
RF Exposure Statement
–To maintain compliance with FCC’s RF exposure guidelines,,
This equipment should be installed and operated with a minimum distance of
20cm from the radiator of your body.
–This device and its antenna(s)must not be co-located or operated in
conjunction with any other antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>