DEWALT DW317 Variable Speed Orbital Jigsaw with Keyless Blade Change Instruction Manual

If you have questions or comments, contact us.
1-800-4-DEWALT ·www.dewalt.com
INSTRUCTION MANUAL
DCS317
Variable Speed Orbital Jig Saw with Keyless Blade Chang

DEWALT Industrial Tool Co., 701 Joppa Road, Towson, MD 21286 (JUN15) Part No. N434634 DCS331 Copyright © 2012, 2013, 2015 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the “D” shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury that, if not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL-FREE
AT: 1-800-4-DEWALT (1-800-433-9258).
WARNING: To reduce the risk of injury, read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term ‘power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

1. Keep the work area clean and well-lit.
   Cluttered or dark areas invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
   Power tools create sparks that may ignite dust or fumes.

3. Keep children and bystanders away while operating a power tool.
   Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
   Unmodified plugs and matching outlets will reduce the risk of electric shock.

2. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators.
   There is an increased risk of electric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet conditions.
   Water entering a power tool will increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

5. When operating a power tool outdoors, use an extension cord suitable for outdoor
   Use of a cord suitable for outdoor use reduces the risk of electric shock.

6. If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply.
   The use of a GFCI reduces the risk of electric shock.

3. PERSONAL SAFETY

1. Stay alert, watch what you are doing, and use common sense when operating a power toot Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury
2. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure the switch is in the off position before connecting to a power source and/or battery pack, picking up or carrying the toot Carrying power tools with your finger on the switch, or energizing power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury
5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
   The use of dust collection can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power tool for your application.
   The correct power tool will do the job better and safer at the rate at which it was designed.

2. Do not use the power tool if the switch does not turn on and off.
   Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
   Such preventive safety measures reduce the risk of starting the power tool accidentally

4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.

6. Many accidents are caused by poorly maintained power tools.
   Keep cutting tools sharp and clean.
   Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control

7. Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be
   Use of the power tool for operations different from those intended could result in a hazardous situation.

5. SERVICE

1. Have your power tool serviced by a qualified repair person using only identical replacement parts.
   This will ensure that the safety of the power tool is maintained.

Additional Specific Safety Rules for Jig Saws

• Hold power tool by insulated gripping surface; when performing an operation where the cutting accessory may contact hidden wiring.
  Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock

• Use clamps or another practical way to secure and support the workpiece in a stable
  Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

• Allow the motor to come to a complete stop before withdrawing the blade from the ken` (the slot created by cutting).
  A moving blade may impact the workpiece causing a broken blade, workpiece damage or loss of control, and possible personal injury.

• Keep handles dry, clean, and free from oil and grease.

• This will enable better control of the tool.

• Keep blades sharp.
  Dull blades may cause the saw to swerve or stall under pressure.

• Clean out your tool often, especially after heavy use.
  Dust and grit-containing metal particles often accumulate on interior surfaces and could create an electric shock hazard.

• Do not operate this tool for long periods of time.
  Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of

• Air vents often cover moving parts and should be avoided.
  Loose clothes, jewelry or long hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety.
  The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in
  line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Minimum Gauge for Cord Sets

  Ampere Rating| Volts| Total Length of Cord in Feet (meters)
  120V| 25 (7.6)| 50 (15.2)| 100 (30.5)| 150 (45.7)
  240V| 50 (15.2)| 100 (30.5)| 200 (61.0)| 300 (91.4)
  More Than| Not More
  Than| AWG
  0| 6| | 18| 16| 16| 14
  6| 10| 18| 16| 14| 12
  16| 16| 14| 12
  10| 12
  12| 16| 14| 12| Not Recommended

**WARNING: ALWAYS** use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use a face or dust mask if cutting operation is dusty. ALWAYS WEAR CER77RED SAFE l Y EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.

**WARNING:** Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote the absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or another injury. Always use NIOSH /OSHA-approved respiratory protection appropriate for dust exposure. Direct particles away from face and body.
**WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or another injury. Always use NIOSH/OSHA-approved respiratory protection appropriate for dust exposure. Direct particles away from face and body. may or may not need this warning, depending on tool:
WARNING: Always wear proper personal hearing protection that conforms to ANSI 512.6 (S3.19) during use.**
Under some conditions and duration of use, noise from this product may contribute to hearing loss.
The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V …………………volts
Hz ……………….hertz
min ……………..minutes
or DC …..direct current
……………….Class I Construction (grounded)
……………….Class II Construction (double insulated)
…/min …………per minute
IPM ……………..impacts per minute

SPM ……………strokes per minute
……………….visible radiation
A …………………….amperes
W ……………………watts
or AC ………….alternating current
or AC/DC……alternating or direct current
no …………………..no-load speed
n …………………….rated speed
…………………..earthing terminal
**** ……………………safety alert symbol
BPM ……………….beats per minute
RPM ……………….revolutions per minute
Sfpm ……………….surface feet per minute

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor
Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than 10% will cause loss of power and overheating. DEWALT tools are factory tested; if this tool does not operate, check the power supply.
COMPONENTS (Fig. 1, 2)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.
A. Trigger switch
B. Lock button
C. Speed control dial
D. Keyless blade lever
E. Shoe

OPERATION

WARNING: To reduce the risk of injury, turn the unit off and disconnect it from the power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.
Trigger Switch (Fig. 1)

To start the jigsaw, squeeze the trigger switch (A).
To slow and stop the jigsaw, release the trigger switch.
For continuous operation, squeeze the trigger switch then depress the lock button (B).
Once the lock button is depressed, release the trigger switch.
To release from continuous operation , squeeze the trigger and the lock will disengage.
Variable Speed Switch (Fig. 1, 2)
The variable speed is controlled in two ways: the speed control dial (C) and the trigger switch (A).
SPEED CONTROL DIAL
By rotating the speed control dial (C) in either direction, the maximum speed or strokes-per minute at which the blade will cut is adjusted. The speed control dial adjusts the speed that the blade will cut from approximately 500 SPM to approximately 3,100 SPM.
TRIGGER SWITCH
As the trigger switch is pressed in, the strokes-per-minute continue to increase, but not to exceed the maximum setting on the speed control dial. As the trigger is released, the blade strokes per minute reduce.
Blade Installation and Removal (Fig. 3)
TO INSTALL A BLADE

1. Lift the keyless blade lever (D).
2. Insert the blade into the clamp mechanism (F) while guiding the back of the blade into the groove of the guide rollers (G).
3. The shank should be completely inside the clamp mechanism as shown in Figure 4.
4. Release the keyless blade lever.

TO REMOVE A BLADE

1. Lift the keyless blade lever (D).
2. With a slight shake, the blade will drop out.

CAUTION: Do not touch used blades, they may be hot. Personal injury may result.
Bevel Cutting Adjustment (Fig. 5)
Bevel cuts may be made at any angle between 0° and 45°. The shoe is adjusted by loosening the screw (H) on the bottom of the tool and rotating the shoe to the desired angle. After setting the shoe, tighten the screw firmly and use the saw in a normal manner.
Cutting Action – Orbital or Straight (Fig. 6)
CAUTION: Check that the tool is not locked ON before connecting it to a power supply. If the trigger switch is locked ON when the tool is connected to the power supply, it will start immediately. Damage to your tool or personal injury may result. This jigsaw is equipped with four cutting actions, three orbital, and one straight. Orbital action has a more aggressive blade motion and is designed for cutting in soft materials like wood or plastic. The orbital action provides a faster cut, but with a rougher cut across the material. In orbital action, the blade moves forward during the cutting stroke in addition to the up and down motion.
NOTE: Metal or hardwoods should never be cut in orbital action.
To adjust the cutting action , move the cutting action lever (I) between the four cutting positions: 0, 1, 2, and 3. Position 0 is straight cutting. Positions 1, 2, and 3 are orbital cutting. The aggressiveness of the cut increase as the lever is adjusted from one to three, with three being the most aggressive cut.
Adjustment For 90° Cuts

1. The 0° mark on the quadrant plate should line up with the mark on the shoe.
2. If adjustment is necessary, loosen the screw on the quadrant plate and adjust as necessary. Place a right angle against the blade and the shoe and adjust the shoe to 90°.

Anti-Splintering (Fig. 7)
This jigsaw has a special double-ended shoe with a wide opening at one end for general cutting and bevel cutting and a very narrow slot at the other end for use only with hollow ground blades. This narrow slot acts as an anti- splintering device (J) particularly useful when cutting plywood.
Reversing Shoe Position (Fig. 7) To reverse the shoe position remove the screw (H) from the bottom of the tool, as shown in Figure 7, and remove the shoe from the jigsaw. [Be careful to note the position of the clamp (K). This clamp must be re-installed the same way or the shoe will not fit properly.] Turn the shoe around and re-install noting carefully that, when the slot is forward, the screw goes through the hole in the shoe and when the wide opening is forward, the screw passes through the slot in the shoe.

Cutting

WARNING:
The jigsaw should not be operated on with the shoe removed or serious personal injury may result.
POCKET CUTTING (FIG. 8, 9)
A pocket cut is an easy method of making an inside cut. The saw can be inserted directly into a panel or board without first drilling a lead or pilot hole. In pocket cutting, measure the surface to be cut and mark clearly with a pencil. Next tip the saw forward until the front end of the shoe sits firmly on the work surface and the blade clears the work through its full stroke. Switch the tool on and allow it to attain maximum speed. Grip the saw firmly and lower the back edge of the tool slowly until the blade reaches its complete depth. Hold the shoe flat against the wood and begin cutting. Do not remove the blade from cut while it is still moving. The blade must come to a complete stop.
WOODCUTTING
Support the workpiece adequately at all times. Use the higher speed setting for cutting wood. Do not attempt to turn the tool on when the blade is against the material to be cut. This could stall the motor. Place the front of the shoe on the material to be cut and hold the jigsaw shoe firmly against the wood while cutting. Don’t force the tool; let the blade cut at its own speed. When the cut is complete, turn the jigsaw off. Let the blade come to a complete stop and then lay the saw aside before loosening the work.
METAL CUTTING
In cutting thin gauge sheet metals, it is best to clamp wood to the bottom of sheet metal; this will ensure a clean cut without the risk of vibration or tearing of metal. Always remember to use a finer blade for ferrous metals (for those that have a high iron content); and use a coarser blade for non-ferrous metals (those that do not have an iron content). Use a high-speed setting for cutting soft metals (aluminum, copper, brass, mild steel, galvanized pipe, conduit sheet metal, etc.). Use lower speed to cut plastics, tile, laminate, hard metals, and cast iron.

MAINTENANCE

WARNING: To reduce the risk of injury, turn the unit off and disconnect it from the power source before installing and removing accessories, before adjusting, or when making repairs. An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing this.
  WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

Lubrication

NOTE: NEVER spray or in any other way apply lubricants or cleaning solvents inside the tool. This can seriously affect the life and performance of the tool. DEWALT tools are properly lubricated at the factory and are ready for use. However, it is recommended that, once a year, you take or send the tool to a certified service center for a thorough cleaning and inspection.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT recommended accessories should be used with this product. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258), or visit our website: www.dewalt.com.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance, and adjustment (including brush inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT authorized service center, or other qualified service personnel. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain a more efficient warranty service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP : In case of an insurance loss, such as fire, flood, or theft, your registration of ownership will serve as your proof of purchase.
• FOR YOUR SAFETY : Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three-Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.
In addition to the warranty, DEWALT tools are covered by our:

1 YEAR OF FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase.
90 DAY MONEY-BACK GUARANTEE
If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country-specific warranty information contained in the packaging, call the local company or see the website for warranty information.
FREE WARNING LABEL REPLACEMENT : If your warning labels become illegible or are missing, call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.

DW317
VS ORBITAL JIG SAW 1″ STROKE (25mm)
WARNING/AVERTISSEMENT
TO REDUCE THE RISK OF INJURY, THE USER MUST READ THE INSTRUCTION MANUAL. ALWAYS USE PROPER EYE AND RESPIRATORY PROTECTION. A TITRE PREVENTIF, LIRE LE GUIDE.
DEWALT INDUSTRIAL TOOL CO., BALTIMORE, MD 21286 U.S.A.
FOR SERVICE INFORMATION, CALL 1-800-4-DEWALT www.DEWALT.com

Epecificaciones DW317
Tensión de alimentación: 120 V CA~
Consumo de corriente: 5,5A
Frecuencia de operación: 50/60 Hz
Potencia nominal: 560 W
Rotación sin carga: 0-3 100 SPM
SOLAMENTE PARA PROPÓSITO DE MÉXICO:
IMPORTADO POR: DEWALT INDUSTRIAL TOOL CO. S.A. DE C.V.
AVENIDA ANTONIO DOVALI JAIME, # 70 TORRE B PISO 9
COLONIA LA FE, SANTA FÉ
CÓDIGO POSTAL : 01210
DELEGACIÓN ALVARO OBREGÓN
MÉXICO D.F.
TEL. (52) 555-326-7100
R.F.C.: BDE810626-1W7

References

• DEWALT® Power Tools Official Site | Guaranteed Tough®
• Sign in & Create Account | DEWALT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>