MARVODiY Re-Defined 68 Wireless Hot-swappable Mechanical Keyboard Kit User Manual
- June 5, 2024
- MARVODiY
Table of Contents
MARVODiY Re-Defined 68 Wireless Hot-swappable Mechanical Keyboard
Kit
LIGHT PROMPT
- The prompt light above the Q/W/E key is the mode switch prompt light.
- Blue light: Bluetooth mode
- Green light: 2.4G mode
- Red light: wired mode
BATTERY REMINDER
When the keyboard battery low , the alarm red light flashes slowly at a
frequency of 1/2 second, and the backlight is turned off.Prompt to charge the
keyboard.
DIP SWITCH FUNCTION
There is a DIP switch function and DIP switch function under the movable
tripod on the back of the keyboard In order to facilitate users to switch
button functions without driving, it is suitable for different scenarios.Dip
switch downwards is the default state, and no function will be changed in this
state.
(After adjusting the DIP switch, the keyboard must be powered off and
reconnected to take effect.After DIP returns to the default position, set it
in the driver to make the driver button customization take effect)
After the DIP switch is moved up to ON:
- Left Win key becomes left FN.
- 2: The left Capslock and left ctrl keys are swapped.
- 3: Lock the windows key, this key has no function after being locked. 4:
- Turn off the keyboard energy-saving sleep function.
- 5: The key position is switched to the Mac OS system key arrangement.
SMART POWER-SAVING FUNCTION
The keyboard automatically shuts down after 6 minutes without any key action
in 2.4G and the Bluetooth mode button backlight, automatically enter the
power-saving sleep state after more than 30 minutes without any button
action,After entering the sleep state, press any key to wake up the keyboard.
SWITCH-MODE POWER SUPPLY
The switch near the type-c interface on the side of the keyboard is the power
switch, flip this switch to the right to ON It is the keyboard power-on state,
and the switch to the left side is OFF to cut off the power supply.Turn off
the keyboard energy-saving sleep function.
SPECIFICATIONS
- Matrix: 68 Keys
- Backlight type: RGB
- Wired mode working voltage: 5V±0.5V
- Wired mode working current: 🙁 180mA
- Wireless mode working voltage: 3.0 – 4.2V
- Built-in battery: 3.7V 2000mA/h
- Charging current: 5V/1Ao
- 2.4G/Bluetooth mode open button backlight state working current: :(180mA
- Turn off the key backlight state working current: :(20mA
- Connection type: Wired/2.4G Wireless/Bluetooth
- Interface type: USB type-C/2.4G Receiver/Bluetooth 5.0
- Switch hot swap type: both 3 pin and 5 pin MX mechanical switches
WIRED MODE
Use the data cable to connect the keyboard to the computer,and then use the
key combination FN+ [}J to switch to wired mode.
2.4G MODE
Use the key combination FN+ [I] to switch to 2.4G mode, and check the USB
wirelessWhether the receiver is plugged into the computer USB port , Plug in
the USB receiver to use 2.4G wireless connection mode,When the keyboard leaves
the factory, the 2.4G mode has been paired, so there is no need to pair again,
such as to pair, you need to switch to 2.4G mode, and then press and hold for
3 seconds to check the code status.1/8 second flashes quickly, and then plug
in the 2.4G receiver to pair successfully.
SYSTEM REQUIREMENT
Wired Mode
Windows XP/Vista/ Win7 / Win8/ WinlO/Winll/Mac 2.4G Mode: Windows XP/Vista/
Win7 / Win8/ WinlO/Winll/Mac Bluetooth Mode: Win8/Winl0/Winll/Mac(Incompatible
with win7 and below systems)
Usb Port
Free USB (1.1/2.0/3.0/3.1) port
INSTALLATION STEPS
- Take out the keyboard, insert the USB data cable plug into the computer USB interface, or insert the 2.4G receiver into the computer USB interface, and turn on the keyboard power switch.
- The system will automatically install the driver, if the installation fails, please restart the computer.
- When the computer prompts that the installation is complete, you can use the keyboard at this time.
BLUETOOTH MODE
- Default Bluetooth device name: BT5 .0 Keyboard
- Bluetooth mode can connect and switch three devices at the same time.
- Bluetooth 1 (BTl) / Bluetooth 2 (BT2) / Bluetooth 3 (BT3) Press FN+Q key combination to switch to Bluetooth mode, long press FN+A/S/D key 3 seconds is the corresponding Bluetooth pairing.
- After Bluetooth pairing is completed, short press FN+A/S/D Switch between Bluetooth devices.
- C. A/S/D key Bluetooth status indicator.
- Switch to BTl device, display blue light.
- Switch to BT2 device, display cyan light.
- Switch to BT3 device, display purple light.
**FUNCTION LAYOUT
**
FUNCTION KEY COMBINATION
Pressing and holding the “FN” key and the function key will activate the
second function of the function key.
PRODUCT WARRANTY
Thank you for your trust and support for our products. In order to let you use this product with confidence and better protect your rights and interests, our company will strictly abide by and implement relevant regulations and implement after-sales service.12 months from the date of purchase.Service content: Service according to the regulations on repair and replacement of micro-computer goods.Not within the scope of the service:
- Exceeded the effective service or free maintenance period.
- Failure to use, maintain, and maintain the fault or damage according to the correct instructions for use.
- Failure or damage caused by maintenance of the maintenance organization authorized by the company.
- No dealer information and stamped products on the warranty card.
- Unauthorized alteration of the contents of the three-guarantees certificate.
- Due to force majeure natural disaster, etc.
- Human factors lead to undesirable products incorrect operation, bump, input inappropriate voltage, etc.
- Other non-product design, technology, manufacturing, quality and other problems lead to failure or damage.
SHENZHEN MARK TECHNOLOGY CO., LTD.Add.6th Floor, Building A, DongFangYaYuan, Chen Tian community, XiXiang, Baoan 2nd Road, Bao’ a District, Shenzhen, China (COMPANY) www.marvopro.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>