AIRCRAFT AM-755 Espresso Machine Instruction Manual

Instruction Manual Aircraft Espresso AM-755

AM-755 Espresso Machine

ESPRESSO MACHINE WITH BUILT-IN GRINDER AND DOUBLE PID

COMPONENTS :

1. Cold water tank
2. Cup warmer
3. \
4. Steam/hot water knob
5. Strainer holder retaining ring
6. Steam/hot water tube
7. Removable cup rest
8. Strainer holder
9. Single-cup strainer
10. Two-cup strainer
11. On/off switch
12. \
13. Coffee/hot water/steam lever switch
14. Indicator light: machine ready| 15. Coffee press
16. \
17.   Coffee beans container
18.   Filter for pods
19.   Removable water drainage tray20.   Removable ground coffee tray 21. Ground coffee switch
22.   Grinding degree scale
23.   Grinding regulation knob
24.   Ground coffee distributor
25.   Manometer
26.  Pump lever switch
27.   Double PID
---|---

USER INSTRUCTIONS

Starting the machine:

1. Remove the machine from its packing and make sure all packing parts have been taken off (including the protection bags).

2. Lay the machine on a flat and steady surface far away from hot places and from the water taps.

3. Remove the water tank cover on the back of the machine and take out the water tank (1) paying attention not to damage the water tubes inside it.

4. Fill tank (1) with cold water.

5. Replace the water tank back in the machine and check that the water tubes are not bent and that the filter is well set on one of them.

6. Plug in the machine in the mains. Make sure that the wall socket is of the right voltage.

7. Place the filter holder (8) under the brewing group (5) and turn it from the left to the right. Leave it there so that it can get warm and it gets ready for use.

8. Switch the machine on by pressing the on/off switch (11). The integrated indicator light comes on to confirm the power supply.

9. Open the steam/hot water knob (4).

10. Position the lever switch (13) on coffee mode and press the pump switch (26).

11. When water comes out of the steam nozzle (6), push the pump switch down (26) and close the steam/hot water knob (4).

12. After completing all these operations, leave the machine on.

13. The PID (27) will visualize the degrees inside the boiler and will control the boiler’s heating.

14. The PID is already set by the producer on 95°C for coffee mode, i.e. the ideal temperature for a good cup of coffee. (If you want to change the PID’s temperature, please follow the instructions written under How to set the temperature inside the boiler by means of the PID).
    Grinding adjustment:

15. As a reference for the grinding degree, a grinding degree scale (20) has been placed on the coffee beans container (19): “7.6.5.4.3.2.1”

16. By taking as a point of reference the tally mark in the machine frame and by turning the grinding regulation knob (23), the grinding degree scale will turn accordingly.

17. Choose higher degrees to get coarse-ground coffee, or smaller degrees to get fine-ground coffee.

18. A correct grinding degree (taking into consideration the various coffee blends) is essential to get a good cup of coffee. We suggest degree 3 to get a medium grinding. Preparing an espresso coffee:

19. Check that tank (1) contains water by looking at the water level indicator.

20. Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the machine is off. If it’s on pass to the following point.

21. As soon as the PID’s display shows the set temperature and the indicator light (14) goes on, the machine is ready for use.

22. Place the single-cup strainer (9) or the two-cup strainer (10) in the strainer holder (8) as described in point 7.

23. Drop the bean coffee in the bowl (17)

24. Press the button (21) with the strainer holder (8) to activate the coffee grinder. When you have got the desired coffee quantity, take the strainer holder (8) off.

25. Pack the coffee in the strainer against the press (15).

26. Insert the strainer holder (8) in the retaining ring (5) and turn it hard to the right; place the cups on the removable cup rest (7).

27. Position the lever switch (13) on coffee mode and lift up the pump switch (26). The manometer (25) will show the reached pressure, between 8 and 14 bar.

28. Once you get the desired quantity of coffee, push the pump switch (26) down again

29. . Remove the filter holder (8) and throw away the coffee grounds. Make sure that the filter holder is clean and reposition it in the brewing group to warm up again. Preparing an espresso with the use of coffee pods:

30. Check that the water tank (1) has been filled in with water by looking at the water level indicator.

31. Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the machine is off. If it’s on pass to the following point.

32. As soon as the PID’s display shows the set temperature and the indicator light (14) goes on, the machine is ready for use.

33. Fit the pod filter (18) into the strainer holder (8) that has been warmed up by leaving it attached to the brewing group as described in point 7.

34. Open the single-packed pod not damaging the pod.

35. Place the pod in its filter (18).

36. Insert the strainer holder (8) in the brewing group ring (5), turn it from left to right with force, then put the cup on the removable water drainage tray (7).

37. Position the lever switch (13) on the coffee and lift the pump switch (26). The manometer (25) will show the reached pressure, between 8 and 14 bar.

38. Once you get the desired quantity of coffee, push the pump switch (26) down again.

39. Remove the strainer holder (8) and throw away the used pod.
    Steam:

40. Check that the water tank (1) has been filled in with water by looking at the water level indicator.

41. Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the machine is off. If it’s on pass to the following point.

42. Position the lever switch (13) on steam mode. NB: the PID’s display will automatically show the writing STE and alternatively the set temperature degree for steam. The PID is already set by the producer on 125°C, i.e. the ideal temperature for steam distribution. (If you want to change the PID’s temperature, please follow the instructions written under How to set the temperature inside the boiler by means of the PID).

43. As soon as the light (14) goes on, the machine is ready for use.

44. Open the steam/hot water knob (4). First, some water will flow out and then the steam.

45. Put the cup with the desired infusion under the steam tube (6) and turn the knob (4) completely.

46. When the drink has been suitably frothed, close the steam/hot water knob (4).

47. IMPORTANT: After you have frothed your milk, reopen the steam/hot water knob (4) and position the steam switch (13) on hot water, and lift the pump switch up (26). When the water flows out of the steam tube (6), close the steam/hot water knob (4) again and at the same time push the pump switch down (26) and re-position the switch (13) on coffee again. Clean carefully the steam/hot water tube (6). This operation is needed in order to restore the water circuit inside the machine’s tubes. Hot water:

48. Check that the water tank (1) has been filled in with water by looking at the water level indicator.

49. Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the machine is off. If it’s on pass to the following point.

50. Position the lever switch (13) on hot water mode.

51. As soon as the PID’s display (27) shows the set temperature and the indicator light (14) goes off, the machine is ready for use.

52. Open the steam/hot water knob (4) and lift the pump switch (26).

53. Hot water will flow out from the steam arm (6) immediately.

54. Once you have got the desired quantity of water, repress the switch (26) and close the steam/water knob (4). 55. After obtaining hot water from the arm (6), make sure that there is still water in the tank (1).

HOW TO SET THE BOILER’S TEMPERATURE BY MEANS OF THE PID:

The PID has been set by the producer of this machine on a temperature of 95°C for coffee mode and on 125°C for steam mode. In order to change the temperatures please proceed as follows:

• Press the button once: the display will show the writing “t1” that refers to the coffee thermostat set to 95°C
• Press the button twice: the display will show the writing “t2” which refers to the steam thermostat set at 125°C
• as soon as the display shows the writing t1 or t2 press the button to to change the previously set temperature. NB: in order to change the temperature’s value it’s necessary to press the button first and only afterward you can help yourself with the buttons in order to set the desired temperature, decreasing or increasing it.
• after 3 sec. from pressing the last button, the inserted temperature is memorized and the display shows the set temperature for coffee or steam.
• the temperature’s value can be set starting from a min. of 80C° up to a max. of 130C° for coffee mode and from a min. of 120°C up to a max. of 140°C for steam mode. NB: the display will flash while changing from steam mode to coffee mode and it will automatically stop only after reaching the set temperature for coffee mode.

Useful Tips:

• The strainers (9 and 10) do not need to be washed after every single use but we suggest checking that the holes are not obstructed.
• For a better result, we suggest keeping the cups warm on the cup warmer (2) which only operates by machine on.
• The PID (27) is already set by the producer at the right temperature for an excellent espresso and a constant steam distribution. During heating and coffee or water distribution, the temperature can oscillate (+/- 10/12°C). Also, a warning has been inserted for coffee mode (t1): after 108°C the PID’s display shows the temperature but intermittently; this is normal and it warns the user that the temperature is too high for a good espresso.

Routine maintenance and precautions:
It is recommended to clean, after each use, the steam tube and the strainer holder carefully

• For cleaning it is recommended the use of a wet damp cloth
• Do not leave the machine outdoors. And do not immerse the machine in water.
• The machine can be used only by adults and must be kept away from children
• Do not wash the strainer and strainer holder in the dishwasher.
• For any problem pls contact an authorized service center.

TECHNICAL DATA:

Voltage: 230 V – 50 Hz; 120 V – 60 Hz
Power: 1200 W
Heating time: ca. 3 min.
Pump pressure: 15 bar
PID regulation: from min 80° C to max 130° C for the coffee mode; from min 120° C to max 140° C for the steam mode
Water tank: 2.7 litres
Dimensions: 31,52537 cm
Weight: 10.2 kg
To be operated with ground coffee and coffee pods

TROUBLESHOOTING:

Dear Customer,
We thank you for buying one of our products, made in accordance with the most up-to-date technological innovations.
Following carefully the simple operations of use contained in this manual, which comply with essential safety regulations, you will get the best performances and notice the remarkable reliability of this product over the years.
You find here below an easy table describing some malfunctioning of the machine with its solutions:

1.Use different coffee
2. Improper grind| 2. Adjust the coffee grind
3. Too little coffee in the filter| 3. Put more coffee in the filter
4. The filter holder has not to be tightened under the brewing group ring| 4. Tighten better the filter holder
Coffee too cold| 1. The machine had not reached the proper temperature| 1. See sections “Starting the Machine” and “Making an Espresso Coffee”
2. Filter-holder not preheated| 2. Filter-holder must be heated together with the water – see section “Starting the Machine”
3. Cups not preheated| 3. Properly heat the cups on the cup-warmer
4. Pressure switch malfunction.| 4. Contact the nearest SERVICE CENTER
Coffee is produced too quickly| 1. Coffee too coarsely ground| 1.Use a finer grind
2. Not enough coffee in the filter| 2. Put more coffee in the filter
3. Coffee not pressed enough| 3. Press coffee more firmly
4. Coffee/pod old or unsuitable| 4.Use different coffee/pod
Coffee leaks| 1. Filter-holder not properly inserted| 1. Insert the filter holder correctly
between the coffee group and the filter- holder| 2. Too much coffee in the filter| 2. Put less coffee in the filter
| 3. Edge of the filter holder is not clean| 3. Clean the edge of the filter-holder
| 4. The douche seal is worn or damaged| 4. Contact the nearest SERVICE CENTER
| 1. Coffee too finely ground| 1.Use a coarser grind
2. Too much coffee in the filter| 2. Put less coffee in the filter
Coffee is produced in drops| 3. Coffee too firmly pressed| 3. Press the coffee more gently
The machine does not produce steam| i. Obstructed outlet hole at end of steam pipe| 1. Clean the outlet hole with a needle
2. Too little water in the tank| 2. See the section “Starting the Machine”
No coffee is produced during the coffee cycle| 1. Too little water in the tank| 1. Fill the tank
2. Steam switch on| 2. Turn off the steam switch
3. Coffee too finely ground| 3.Use a coarser grind
4. Too much coffee in the filter| 4. Put less coffee in the filter
5. Coffee too firmly pressed| 5. Press the coffee more gently
6. Shower plate obstructed| 6. Contact the nearest SERVICE CENTER
The machine does not work and the ON light does not go on| 1.No electricity| 1. Restore electrical power
2. The main cable is not properly plugged in| 2. Plug the main cable incorrectly
3. The main cables damaged| 3. Contact the nearest SERVICE CENTER for a replacement cable
The ON light is on and the steam light does not go off after 10 minutes| 1. Thermostat malfunction,| 1. Contact the nearest SERVICE CENTER
2. Heating element malfunction| 2. Contact the nearest SERVICE CENTER

The inserted data and pictures can be subject to changes without previous notice for the improvement of the machine’s performance.

LEGAL WARRANTY

This product is covered by the warranty laws valid in the country where the product has been sold; specific information about the warranty terms can be given by the seller or by the importer in the country where the product has been purchased. The seller or importer is completely responsible for the product.
The importer is completely responsible also for the fulfillment of the laws in force in the country where the importer distributes the product, including the correct disposal of the product at the end of its working life.
Inside the European countries, the laws in force are the national laws implementing the EC Directive 44/99/CE.
IMPORTANT INFORMATION FOR THE CORRECT DISPOSAL OF THE PRODUCT IN IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC
**** At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differential waste collection center or to a dealer providing this service. Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal enables the constituent materials to be recovered to obtain significant savings in energy and resources. As a reminder of the need to dispose of household appliances separately, the products are marked with a crossed-out wheeled dustbin.

CONTACT :
ACT : Aircraft Espresso
25 rue de Galeben
33 380 Miles
France

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>