FLYINGTECH WS500 Pro Wireless Video Transmission User Manual

FLYINGTECH -WS500 -Pro -Wireless -Video -Transmission

Important Safety Instructions

The device has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the device should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.

• Please do not place the display screen towards the ground to avoid scratching the LCD surface.
• Please avoid heavy impact.
• Please do not use chemical solutions to clean this product. Simply wipe with a soft cloth to keep clean of the surface.
• Please do not place on uneven surfaces.
• Please do not store the monitor with sharp, metallic objects.
• Please follow the instructions and trouble-shooting to adjust the product.
• Internal adjustments or repairs must be performed by a qualified technician.
• Please keep user guide for future reference.
• Please unplug the power if long-term no-use, or thunder weather.

Safety Disposal For Old Electronic Equipment

Please do not regard the old electronic equipment as municipal waste and do not incinerate old electronic equipment. Instead please always follow local regulations and hand it over to the applicable collection stand for safe recycling. Ensure that these waste materials can be effectively disposed of and recycled to prevent our environment and families from negative effects.

Accessories

1. Wireless Antenna 4pcs
2. USB-C Cable 1pc
3. Electronic User Manual 1pc

Features

• OLED display
• Automatic frequency selection at high quality frequencies.
• Transmission distance up to 500ft (150m).
• Minimum latency up to 0.08s
• Transmitter supports SDI and HDMI input.
• Receiver supports SDI and HDMI output.
• Connectable to mobile devices and supports APP monitoring.
• Supports Sony NP-F series batteries as well as USB-C power.

Description

Transmitter

1. Antenna connector (RP SMA male)
2. USB 5V
3. HDMI i nput
4. SDI i nput
5.  OLED screen
6.  S elect button
7.  Menu/Confirm button
8.  S elect button
9. 1/4 screw mount
10. Power switch

Receiver

1. Antenna connector (RP SMA male)
2. USB 5V
3. HDMI out put
4. SDI out put
5. OLED screen
6. Select button
7. Menu/Confirm button
8. Select button
9. 1/4 screw mount
10. Power switch

Application

The connection process is shown in the diagram above. The camera and transmitter can be connected via an SDI/HDMI cable. After receiving video signal, the receiver outputs to monitor side via the SDI/HDMI cable.
APP monitoring allows for real-time monitoring as well as mobile device connection. When the transmitter TX has HDMI and SDI input, the receiver RX output recognises the SDI signal from the transmitter TX in priority and outputs the SDI signal from TX, and only recognises the HDMI signal from the TX when the SDI signal is disconnected.

Battery installation/removal

Battery mounting (compatible with Sony NP-F series batteries)

Battery removal

Menu

5-1 Power on the transmitter and receiver

5-2 Press and hold “>” select button to get the local QR code, install the app using your mobile device, and then use the app to scan the QR code to connect.

5-3 OLED screen

1. Wireless signal: current wireless signal status.
2. Wireless channel: wireless channel currently in use.
3. Transmitter/receiver device: show whether the device is a transmitter or a receiver.
4. Video signal display: currently connected wireless video signal, or no video signal.
5. Battery level/DC input: displays the battery level and DC input information.

5-4 Open the menu

Press and hold the Menu/Confirm button to call out menu. Then use the Select button to select the desired menu and press the Menu/Confirm button for menu confirmation.

English
Message| SSID| ID
Password
Version| Version Number
Scan(Only for RX)| Scan: ON/OFF

Specification

23.98/24/25/29.97/30/50/59.94/60fps

1080i 50/60fps 720p 50/60fps

3G-SDI input
HDMI output
3G-SDI output
Audio| 48kHz 24-bit
Transmission| Latency| 80ms (from transmitter to receiver, no signal

interference)

Frequency| 5GHz
Transmission Power| 17dBm
Transmission Range| 500ft/150m (no signal interference)
Power| Power Supply| DC 5V
Power Consumption| ≤3W
Environment| Working Temperature| 0°C ~50°C
Storage Temperature| -20°C ~60°C
Dimension| Dimension (LWD)| 113×65×29mm
Weight| TX: 200g / RX: 200g

APP Monitoring

1. Using an IOS device, download “Wireless video” from the Apple App Store (Android version is not supported at the moment).

2. Press and hold the Select button to get the local QR code, then use a mobile device to scan the QR code to connect.

3. Back/Exit.

4. Display settings: Brightness, contrast, sharpness and peaking focus and exposure

5. More settings: You can set the safety frame, greyscale and center mark.

6. Live stream.

7. Peaking focus shortcut on.

8. Exposure shortcut on.

9. Zoom shortcut: 1x, 2x and 4x can be set.

10. Recording.

11. Take a picture..

Trouble Shooting

1. Make sure that the transmitter and receiver are connected to the same channel.
2. Please check that antenna is correctly installed and locked in place.
3. Please check that the power supply battery or power supply cable is correctly connected.
4. Please check that the transmitter and receiver are successfully paired.
5. Please ensure that the HDMI / SDI connection is correct.
6. lease check if the device output format is compatible
7. If you experience video fluctuations, please manually switch to another channel.

Note: Specifications are subject to change without notice due to continuous efforts to improve products and product features.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>