NIN TS100 Soldering Iron Instruction Manual
- June 5, 2024
- NIN
Table of Contents
NIN TS100 Soldering Iron
Safety Statement
General Safety
- Use only certified power source/adaptors from your region.(please refer to 3.0 for specifications)
- Do not operate in humid environment.
- Do not operate in inflammable/explosive environment.
- Keep the surface of the product clean and dry.
Working condition
| Working condition | Requirements |
|---|
Temperature
| Operating Condition: from 0℃ to +50℃
Non-operating Condition: from -20℃ to +60℃
Humidity
| Operating Condition: from 40℃ to 50 ℃,0% to 60% RH
Operating Condition: from 0℃ to 40 ℃,10% to 90% RH
Non-operating Condition: from 40℃ to 60℃,5% to 60%RH
Warnings
When using TS100, Turn the power off when not in use,or left unattended. When
power is ON,tip temperatures will between 100℃~400℃(212℉~752℉),please be
careful. Please don’t operate TS100 when it’s wet or operate it with wet
hands,which will cause an electric shock.
Cautions
When using TS100,
- The handle is constructed with precision, dropping shall be avoided.
- After continuous use up to 40 minutes, the handle surface temperature will reach 50℃~60℃.
- For the first time using, TS100 may generate a light smoke due to the heating of heating elements, which is a normal phenomenon.
Liability Statement
Any damage of the product,or losses related to the product damage, if it’s
man-caused,or assumed to be man-caused,the liability will belong to the user.
Overview
Ports and Control Panel Introduction
- The tip setscrew
- Button A
- Button B
- Ground cable fixing screw
- Power connector
- Micro USB
- C5525 12-24V port
- Soldering tip port
- Soldering tip connector
- Soldering tip heating end
Specifications
| Working condition | Requirements |
|---|
Temperature
| Operating Condition: from 0℃ to +50℃
Non-operating Condition: from -20℃ to +60℃
Humidity
| Operating Condition: from 40℃ to 50 ℃,0% to 60% RH
Operating Condition: from 0℃ to 40 ℃,10% to 90% RH
Non-operating Condition: from 40℃ to 60℃,5% to 60%RH
Operation Specifications
| Power | 65W |
|---|---|
| Temperature range | 100℃~400℃（max） |
| Temperature stability | ±2% |
| Operation temperature under heat | 40℃ |
| Soldering tip resistance to the ground | <２Ω |
Power Adaptor Selection
Before connecting DC5525(12-24V)power adaptor,check if the adaptor is in good condition as below standard. We would recommend the DYS404-190210V (19V,2.1A)power supply as an accessory for TS100.
Operation voltage
|
Power
|
Electric current
| Time required to increased tip temperature from 30℃ to 300℃
---|---|---|---
12V| 17W| ＞1.4A| 40s
16V| 30W| ＞1.9A| 20s
19V| 40W| ＞2.1A| 15s
24V| 65W| ＞2.7A| 11s
Operation
- Loosen the tip setscrew, insert the soldering tip connector and tighten the screw;
- Connect the ground wire to the ground wire setscrew ;
- Connect the DC connector to TS100, connect the power cord and turn on the power accordingly.
Note: If the screen displays “sen-err”when it’s plugged, means the soldering iron tip is not properly fixed, please re-install it properly.
Default Settings
Default temperature unit
|
℃
---|---
Default temperature
| 300℃（Default）
Sleep mode temperature
|
200℃（Default）
Adjustable temperature range|
100℃~400℃（Max）
Basic Control
When plugged into DC12-24V power adaptor ,TS100 will display its logo, Version number and its standby screen in sequence. When plugging into DC 12-24V power adaport ,pressing Button A at the sametime will enter DFU mode,”DFU1.0″ will appear on OLED screen . To exit DFU mode: unplug and plug in the device again without pressing any button ,then it will enter standby mode.
Automatic Calibration
Note: Calibration shall be done when TS100 in room temperature
Heating up
Temperature Adjustment
Temperature Adjustment
Note: When screen displays arrow pointing to left or right (◀or▶) which means the adjustment has already reached its upper/lower limit temperature, settings will not be saved when power is off
Remark: Maximum temperature: 400℃ Minimum temperature:100℃
When TS100 temperature stabilizes for 60 seconds,it will automaticall yenter feedback mode, temperature status will feedback every 5-8 seconds The last digit on the right end of the display shown as below
Sleep Mode
Note: IDLE_TIME can be adjusted( 6 minutes in Default).(Preset minimum IDLE time: 5 minutes)
System Parameters
Parameter
|
Explanation
|
Default
| Adjustable range
---|---|---|---
T_Standby|
Standby mode temerature
|
200℃
|
100℃~400℃
T_Work
| Operating temperature|
300℃
|
100℃~400℃
Wait_Time
| Time from operation mode to sleep mode| 180
seconds
| 60~9999
seconds
Idle_Time
| Time from sleep mode to standby mode| 360
seconds
| 300~9999
seconds
T_Step
| When preset “1”,each step will progress in 1,2,5,25; when preset 2-25, each step will progress according to settings|
10
|
5-25
Turn_Off_v
| When operation voltage is lower than default voltage TS100 will return to stadby mode|
10V
|
9-12V
TempShowFlag| Temperature unit selection| ℃| 0 is ℃，1 is ℉
ZeroP_Ad
| Temperature calibration parameter, TS100 automatical adjustment| | No manual setting requir
Soldering Iron Tip
Changing Soldering Tips
- Unplug TS100 before changing.
- Loosen the tip setscrew.
- Pull out the tip, replace with another one.
- Tighten the screw.
Note: When TS100 displays “sen-err”, it means the soldering iron tip is not installed properly.
Choosing Soldering Iron Tips
Soldering Iron Tip Maintenance
- Before switching off, wipe the tip’s soldering side with some solder.
- Do not leave the tip in high temperature for long time, which may causeit burn out.
- Do not push too hard while soldering, which will damage the tip.
- Do not use rough material or files to clean the tip.
- If the tip surface is oxidized and makes it hard to apply solder on it, you may use 600~800 grit sandpaper to wipe the tip with Ethanol or Isopropyl alcohol, heat up to 200℃ and apply solder immdeiately to avoid it oxidize again.
- Do not use Flux that contains high chlorine or acid, use only resin based flux.
Soldering Iron Tip Lifespan
Soldering iron tips lifespan is related to its maintenance (refer to 5.3)and
use intensity .
Trouble Shooting Guide
Standard service
1 year of warranty will be provided for one year, if the damage was not caused
by false manipulation by the user.Plesae contact your retailer for warranty
detail Tips are consumables, once it’s used, no replacement will be provided.
Default Parameter Setting
Connect TS100 to your PC with USB data cord, OLED will display “CONFIG” and means it’s in setting mode. Open config.txt file from the USB drive, set the default parameters.
Technical Support
- Visit www.miniware.com.cn and download the latest TS100 firmware to your PC.
- Connect TS100 to your PC with USB data cord,meanwhile,press TS100’s Button A to enter DFU mode once a “DFU1.0” notice appears on the screen. A virtual disk with 8 serial numbers will appear on your PC.
- Copy the hex firmware to the root directory of that disk. When the extension of the firmware changes from “hex” to “rdy”, disconnect USB and the firmware is upgraded
Changing Boot Up Screen
Note: When the “LOGOIN.BMP” exists in the USB drive, the boot up logo will be using the file, if the file doesn’t exist, it will be using the default logo instead
Legal Statements
Disposal
Do not dispose this product with domestic waste Handling and
recycle:Disposal of the product shall be manipulated according to laws and
regulations in your area.
Statement of Fulfilling FCC Standard
This device fulfills part 15 of the FCC regulations Device must fulfill below 2 conditions:
- Device must not generate interference
- Device must be able to resist any interferences on it, including interferences that could cause dangerous manipulation
Statement of Fulfilling CE Standard
This is a trademark of Europe Union This product with CE logo on it fulfills
related Euro Union laws and regulations
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>