ALDER Plus Skybell Doorbell Camera Installation Guide
- June 5, 2024
- ALDER
Table of Contents
ALDER Plus Skybell Doorbell Camera
Included:
- Doorbell Camera
- Wall Mounting Bracket
- Wall Screws ( 2 )
- Wall Anchors ( 2 )
- Set Screw
Complete the pre-install checklist before installing the Skybell Doorbell Camera.
Pre-Install Checklist
Working Doorbell Check
First, check that the existing wired doorbell is working. If the indoor
chime does not ring after pressing the existing doorbell button, there is
likely a power-supply problem that must be solved before installing the
Skybell Doorbell Camera.
Wired Doorbell Check
Remove the existing doorbell button from its mounting location to in-spect for
wires. Next, check the chime. A chime that plugs into a power outlet instead
of being hardwired into the home might be incompatible with Skybell. (See pg.
6 for more information on the chime type)
WiFi and WiFi Password
A home’s internet service must include WiFi with upload speeds of 5 mbps
and a strong enough signal to reach the doorbell location. The WiFi password
is needed to complete the installation.
Mounting Hardware
Skybell uses the existing doorbell wiring and comes with a mounting plate
and hardware to attach it to a flat surface. Installing the mounting plate may
require a power drill.
Mobile App Login
You must download and log in to the Alder app to complete installation.
Doorbell Chime Type
Before installing the Skybell Doorbell Camera, confirm that your home’s existing doorbell components are compatiable.
Mechanical Chime
If the chime has metal bars and a striker pin, it is mechanical and will
work without special hardware.
Digital Chime
If the chime has a speaker that plays a digital tone, it is not currently
supported on the Alder system.
Tube Chime
If the chime has a series of tubular bells, it is a tube chime and is
incompatible with the Skybell Doorbell Camera.
Intercom System
If the doorbell button fixture includes a speaker, it is an intercom system
and is incompatible with the Skybell Doorbell Camera.
No Chime
Installing Skybell Doorbell Camera to work without a chime is a
configuration that is not currently supported on the Alder system.
Installation Steps
Remember to switch off the doorbell circuit breaker before installing the Skybell Doorbell Camera.
-
Remove the existing doorbell button from its mounting. Disconnect the wires. Leave them exposed but separated.
-
Determine where new mounting screws will go. Use the Skybell mounting plate to locate where new screw holes (if any) will be placed. Mark the location(s).
-
Attach Doorbell Camera mounting bracket.
Feed the existing doorbell wires through the hole in the center of the Skybell mounting bracket. Then, attach the bracket to the wall by driving the provided screws through the brackets’ top and bottom holes.- A power drill and special bit will be needed if installing into concrete, brick or stucco.
- Use a screwdriver and the provided screws if installing into wood.
- Use the provided wall anchors for a secure fit if the drill holes are too large
-
Connect power wires to the mounting bracket.
Loosen the terminal screws and wrap the bare ends of the doorbell wires around the screw shafts below the head. Then, tighten the screws. -
Attach the Doorbell Camera to the mounting bracket.
Press the Skybell body over the mounting bracket until it sits snugly in place. Use a small screwdriver (not a power tool) to tighten the set screw on the bottom of the Doorbell Camera body.
-
Switch the circuit breaker back on.
With power back on, You should see Skybell’s LEDs flashing a timed se- quence of color-coded signals in the following order.
- RED/BLUE (alternating) 30-60 seconds = The internal backup battery is charging.
- YELLOW (solid) 20 seconds = Skybell system is starting up.
- RED/GREEN (alternating) = Ready to sync with your Alder Security System.
Once the backup battery is fully charged, Skybell will boot up, then display Red/Green flashing lights. With Skybell’s LEDs flashing Red/Green, follow the steps to sync your new doorbell camera with your Alder Home Security account.
Syncing To The Alder App
- Open the Alder app and log into your account.
- Tap the camera icon in the lower right corner of the home screen. this will take you to the Add Cameras screen.
- Tap the + button on the Add Cameras screen. This will show you a menu of camera options.
- Tap the Skybell image from the camera options menu. Then you’ll be asked to name your new Skybell.
- After typing your Skybell’s new name, tap Continue. This will take you to the screen where you add Skybell to your system.
- Tap Begin on the Add a Skybell screen to start syncing. It may take a couple of minutes to boot up and enter Sync Mode.
- While Skybell is still in Sync Mode, click Continue. Red/Green flashing lights indicate Sync Mode.
- Navigate to the WiFi settings in your phone. Select Skybell HD network, then return to the Alder app.
- Grant the Alder app permission to connect to your network. A prompt should pop up on your smartphone screen asking for permission.
- Connect Skybell to your home WiFi network.In the WiFi networks menu, choose your home network, enter your password, and press Connect. When the light turns solid green, Skybell is ready to use.
LED Reference Guide
Blue | Flashing
Skybell Doorbell Camera is charging.
Blue | Solid
Skybell Doorbell Camera is booting.
Orange | Rapid Double-Flash
No WiFi or lost WiFi connection.
Change the Skybell Doorbell Camera to AP mode by pressing the main button
until it flashes green, then release. Skybell will scan WiFi networks while
the button continues flashing green. After scanning a couple of minutes,
Skybell should sync to your WiFi network in standard mode and begin flashing
an alternating pattern of red and green lights.
Green | Flashing
The Skybell Doorbell Camera is entering troubleshooting mode.
Red & Green | Alternating Flashing
Skybell Doorbell Camera is in standard WiFi syncing mode (AP mode).
Blue & Green | Alternating Flashing
Connected to WiFi but waiting for server connection.
Green | Solid
Skybell Doorbell Camera is ready to use.
White | Solid
“In call” mode or motion was detected by the camera.
Blue | Flashing
Skybell Doorbell Camera is in Power Cycle. Hold the button about two
minutes until the LED flashes blue.
Yellow | Flashing
Factory Reset: Hold the button for about two minutes until the LED flashes
yellow. After Factory Reset, Skybell Doorbell Camera will need to be re-synced
to the Alder security app.
Blue | Rapid Double-Flash
A problem with the Power supply is detected.
Blue & Yellow | Alternating Flashing
A Firmware update is in progress.
Alder Holdings, LLC: AL: 1722 AK: BLN1016763 CLN 103834 AR: E CMPY 2415, Regulat-ed by Arkansas Board of Private Security Investigators and Private Security Agencies, 1 State Police Plaza Drive, Little Rock, AR 72209, 501-618-8600 AZ:19510 CT: HIC.0645215 DE: 15-53 FL: EG-13000528 GA: LVA205370 HI: C36654 ID: RCE-40291 IA: AS-0197 LA: F2235 MD: 107-2166 MI: 3601207212 MN: TS751468 NV: 82188 NE: 28149 NH: 013 NJ: 34BF00060400 NM: 391453 NY: 12000316340 Alder Home Solutions, LLC- Licensed by the N.Y.S Department of State NC: 31398-SP-FA/LV, 2635-CSA North Carolina, Alarm Sys-tems Licensing Board, 4901 Glenwood Ave Suite 200, Raleigh, North Carolina 27612 ND: TM-00532 OH: 53.89.1833 OR: CCB 211314 CLE502 OK: 433297 PA: PA130798 RI: 9603 SC: Burglar BAC.13706 / Fire FAC.13674 TN: 1980 TX: TX DPS: B20412, FM: ACR-2078824 UT: 9515408-6501 VA: 2705161860 11-15183 Alder Home Solutions, LLC WV: WV053739 WA: ALDERHL842M5 WY: LV-G-48405 USVI: 33494 1-33494-1L
MS 15025407 1.844.44.alder [email protected]