KINZO 48P7400 Silence Power Generator Instruction Manual

KINZO 48P7400 Silence Power Generator

SAFETY INSTRUCTIONS

When using the machine, always observe the enclosed safety instructions as well as the additional safety instructions.
The following symbols are used throughout this manual:

• Wear hearing protection.
• Consult the manual.
• Only use the machine outside, in well-ventilated surroundings.
• Do not use the machine in precipitation or in humid surroundings.

Do not use the machine in surroundings where sparks, flames or open fire can be present. Do not smoke near the machine.

ADDITIONAL SAFETY INSTRUCTIONS FOR GENERATORS

• Place the machine on a solid surface. Do not place the machine on a metal surface.
• Do not place the machine in the blazing sun. Do not expose the machine to temperatures over 40 °C. Do not store the machine in humid surroundings.
• Before use check whether the power input of the equipment to be connected is less than the maximum output of the generator.
• Only connect the equipment when the generator is running at full speed. Disconnect the equipment before switching off the generator.
• Do not connect any other energy sources to the machine. Do not connect the machine to mains supply.
• Immediately switch off the generator in one of the following situations:
  • hitches or unstable running of the motor
  • decrease of the electrical output
  • overheating of the connected load
  •  excessive vibrating of the generator
  •  sparking
  •  presence of smoke or fire
•  Make sure that the generator has enough fuel when connected to the load.
• Never add fuel when the machine is running. After use let the machine cool down for at least 15 minutes before refuelling.
•  Avoid touching hot parts of the machine.
• Do not store fuel near the machine.
• The sound absorber and the air filter function as flame catchers in case of after-burning. Therefore see to it that they are mounted properly and are in good technical condition.

DESCRIPTION

This generator was designed to generate electricity to supply electrical machines or equipment.

1. On/off switch
2. Alternating voltage indicator lamp
3. Volt meter
4. Reset switch alternating current output
5. Lid fuel tank
6. Alternating current output
7. Earth connector
8. Oil bleeding plug
9. Dipstick
10.  Fuel cock
11. Choke
12. Start cord
13. Air filter cover

Adding fuel

Never add fuel when the machine is on. After use let the machine cool down for at least 15 minutes before refuelling. Always use fuel that fulfils the following specifications: unleaded petrol, octane content at least 85 Never smoke near the machine or the fuel. Never add fuel in the vicinity of sparks, flames or open fire.

• Remove the lid (5) from the filler opening.
• Pour the fuel carefully in the filler opening. Never fill the tank further than to the top of the fuel filter.
•  Place the lid back on the filler opening.

Starting the motor

• Be sure that no load is connected.
• Turn the fuel cock (10) to the position “ON”.
• Fully pull out the choke (11).
• Put the on/off switch (1) in the position “ON”.
• Pull gently on the start cord (12) until you feel resistance.
•  Pull the start cord forcefully. Repeat this until the motor is starting.
• Slowly push the choke again.

Instructions for use

• Start the motor as described above.
• To connect an electrical machine

Load protection device
In case of overload or short circuit, the overload protection device interrupts the circuit. Wait at least 1 minute before operating the reset switch (4).
Switching off

• Be sure that no load is connected.
• Put the on/off switch (1) in the position “OFF”.
• Turn the fuel cock (10) to the position “OFF”.

CLEANING AND MAINTENANCE

For good functioning and a long lifespan for the machine, regular cleaning and maintenance is essential.

• Do not perform any cleaning or maintaining activities while the motor is running.
• Do not smoke during the below work.

Changing the oil

The oil must be changed after the first 20 operating hours, and then after every 100 hours or 6 months.

• Place a receiving bin under the bleeding point.
•  Remove the dipstick (9) from the filling-point.
• Remove the screw from the bleeding point (8).
• Tilt the machine slightly forwards to remove all oil.
• Re-insert the screw and tighten it securely.
• Fill the crankcase with the prescribed amount of oil.
• Replace the dipstick.

Checking the oil level

• Remove the dipstick (9) from the filling-point.
• Clean the dipstick.
• Insert the dipstick into the filling hole for a few seconds before pulling it out again.
• Check the oil-level. The oil level should be at a rate between high and low.
•  If the level is below this mark, refill the oil.
  • Use a funnel to avoid spilling.
  • For easy filling, tilt the machine slightly backwards.
•  Mount the dipstick.

Cleaning the air filter

Clean the air filter every 50 operating hours

• Loosen the two clamping brackets (14).
• Remove the lid (13).
• Remove the air filter (15) from the filter holder (16).
• Clean the filter with spirits or ethanol.
• Pinch the filter out. Do not twist!
•  Immerse the filter in clean motor oil.
• Pinch the filter out and mount it into place.
• Re-fit the filter.
•  Re-fit the cover.

Cleaning the fuel

• Remove the lid (5) from the filler opening.
• Lift the fuel filter (17) from the filler opening.
• Clean the filter with spirits or ethanol.
• Dry the filter with a soft cloth.
• Replace the filter in the filler opening.
• Place the lid back on the filler opening.

Cleaning the filters in the fuel pipe
The filters in the petrol tap and the settler must be cleaned in time in order to avoid obstruction.

• Clean the filters with petrol.

Checking the spark plug

• Remove the spark plug cable (18) from the spark plug.
• Remove the spark plug (19) using the spark plug spanner.
• Clean the electrode (20) using a steel brush.
• check the contact distance (correct value 0.7 -0.8 mm) and adjust as necessary.
•  Replace the spark plug.

TROUBLE SHOOTING

If the machine is not working properly, take the following steps to correct the problem. If you cannot correct it yourself, contact your dealer.

Engine does not start

• Check if the fuel tap is open.
• Check if there is fuel in the tank.
•  Check that the on/off switch is in the “ON” position.
• Check the oil-level.
• Pull harder on the start cord.
• Check if the spark plug cable is on the spark plug.
• Clean the spark plug and check the contact distance.

Motor runs irregularly

• Check if the spark plug is properly placed.
• Check if the spark plug cable is on the spark plug.
• Clean the spark plug and check the contact distance.
• Check if the right fuel has been used.

Generator supplies no energy

• Check if there has been a short circuit or an overload.
• Check that the reset switch is in the “ON” position.
• Check the wiring.

TRANSPORT AND STORAGE

If the machine is out of use for a longer period of time, the fuel tank must be emptied and the oil must be changed.

• Empty the fuel tank.
• Change the oil.
• Cover the machine and place it in a clean an dry environment.

TECHNICAL DATA

• Output voltage: V 230
• Output voltage: A 10.8
• Output capacity: VA 2,000
• max: kVA 2.3/5 min.
• Output frequency: Hz 50
• Fuel consumption: l 0.47
• Max. fuel consumption: l/h 1.43
• Contents fuel tank: l 13.5
• Crankcase capacity: l 0.47
• Dimensions: mm 600 x 430 x 445
• Weight: kg 42.3

Level of sound pressure:

• L pA (sound pressure): dB(A) 75
• L WA (acoustic power): dB(A) 95

GUARANTEE
Refer to the enclosed guarantee conditions for the terms and conditions of guarantee.

ENVIRONMENT
Should your machine need replacement after extended use, do not put it in the domestic waste but dispose of it in an environmentally safe way.

DECLARATION OF CONFORMITY

Kinzo B.V. declares that the machines: Generator 48P7400 have been designed in compliance with the following standards: EN 55012, EN 55014-1, EN 61000-6, EN 122601 and in accordance with the following directives: 73/23/EEC, 89/336/EEC, 93/68/EEC, 97/68/EC, 98/37/EC, 2000/14/EC, 2002/88/EC
The EC type approval has been provided by: TÜV Rheinland Product Safety GmbH, Am Grauen Stein,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>