IKEA BEKANT Stained Oak Desk Instruction Manual

IKEA BEKANT Stained Oak Desk

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Translated from the original instructions.

• Advice and instructions for BEKANT sit/stand desk.
• Sound level: lower than 55 dB(A)
• Height setting interval:
• EU-version: 64-125 cm
• NA-version: 57,4-122,4
• Maximum load: 70 kg
• Temperature interval at usage: +5 up to +40 degrees C
• Temperature interval at storage: -10 up to +50 degrees C
• Humidity: 20% up to 80% at +30 degrees C.
• Power supply unit: DC 29V, 200W / 220W (JP)
• Manufacturer: ROL ERGO
• Model: ASW0579-2902002W / ASW0643-29020002W (JP)

This appliance shall only be used together with the included power supply unit.
Every person who is responsible for this table at installation or employment of the table in daily use or in service and repair work should carefully read these instructions. Keep these instructions close to your sit/ stand table.

Installation instructions

• The table is assembled according to separate assembly instructions.

• Connect the cable from one leg to the other. Connect the hand control to one of the leg and the power-supply to the other leg. The cables to the legs, hand control and power supply should be placed in the accompanying net. Place the electrical cables so that they do not get damaged, see assembly instruction.

• Connect the electrical cable to a wall socket. NB!
  The electrical cable must have full mobility.

• Insert the safety key in the socket on the hand control.

• The table is now ready for use. The motors stop automatically when the table reaches its lowest and highest position respectively.

Usage of the table

• The table shall only be used as a working table with the possibility to continuously adjust working height between sitting and standing position.
  The table shall only be used indoors and in dry premises (office environment or similar).

• The table must not be overloaded – maximum load is 70 kg/154 lbs. The motors may be run continuously for maximum 1 minutes. Afterward, the motors must stand by for approx. 9 minutes before they can be used again.

• Follow these instructions when adjusting table height:

  • Insert the safety key in the socket on the hand control.
  • Make sure no objects are in the way of the table adjusting height freely.
  • In order to run the table up/down, press the manoeuvre button with an arrow pointing up and down respectively.

Safety regulations

• When the table is run up/down, keep the necessary safety distance to avoid the risk to get squeezed between the moving table top and fixed objects in the surrounding area.
• When the table is run up/down the user shall keep watch so that nobody is injured or no object is damaged. The table top must not bump into a fixed object so that the table is overturned. Always remove any office chair before the table is run up/ down.
• When the table is left unattended, the safety key must be removed from the hand control and placed out of reach of children.
• The table tripod must not be altered or reconstructed in any way. In service and repair work of the table, the electrical cable must always be disconnected from the wall socket.
• Alterations to the control box are absolutely forbidden!
• The table must not be used as a hoisting device for persons.

Maintenance and repair instructions

• After approx. 1 week of use, check that the screws are properly tightened.
• If the table cannot be lowered or raised, check the connections between the legs and the wall socket and be sure the safety key is inserted in the hand control.
• If any part of the electrical system is replaced, the electrical cable must first be disconnected from the wall socket. Replace the electrical part and then connect the electrical cable to the wall socket. The table is now ready for use.

If the table still does not work, please contact your nearest IKEA store or customer service.
Manufacturer: IKEA of Sweden AB
(commercial registration number: 556074-7551)
Address: Box 702, SE-343 81 Älmhult, SWEDEN
Telephone no.: +46(0)476-648500
SAVE THESE INSTRUCTIONS

DISPOSAL

The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store. EU Declaration of Conformity is included in the packaging as a separate document.

Perform a reset by

Simultaneously pressing the up and down buttons for minimum of 8 second

Press and hold the down button and the desk will slowly move the lowest point possible

The desk/ stand is ready for normal use

Troubleshooting

IKEA BEKANT – iDrive

| |
---|---|---
Problem| Check| Try
The underframe will not move.| 1.     Make sure that all cables are undamaged and connected.

2.     Make sure that the safety key is correctly inserted into the hand control.

3.     Unplug the desk from the wall socket for approximately one minute and reconnect.

| Connect the cables and insert the safety key.

Follow the installation instructions and perform a reset.

If problem remains, contact IKEA customer service.

Only one leg is moving.| | Perform a reset. If there’s still only one leg moving, contact IKEA costumer service.
Both legs are moving but at different speeds.| | Perform a reset. If legs still are moving at different speeds, contact Ikea customer service.
The underframe only moves short distances.| Make sure that the desk is not overloaded, and that the safety key is correctly inserted in the hand control.| Move any load off the desk and insert the safety key securely. Perform a reset. If the problem remains, contact IKEA customer service.
The underframe stops and reverses during operation.| Make sure that nothing is blocking the table.| Remove the obstacle. Perform a reset. If the problem remains, contact IKEA customer service.
The underframe can only move in one direction (up or down).| | Perform a reset. If problem remains, contact IKEA customer service.
The desk is not horizontal.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>