MosArt MS221 2.4G Device User Manual
- June 5, 2024
- MosArt
Table of Contents
MS221 2.4G Device
User Manual
Indroduction
MosArt design 2.4G EMI mode, via 2.4G device Keys of the operation, simple
control Mouse, Keyboard, Dongle end of EMI testing different models.
MosArt design EMI mode, applicable to CE, FCC, TELEC (Japan), KCC (Korea), NCC
(Taiwan )…. and other relevant provisions of the test.
Simple operation instructions
2.4G KB, MS, Dongle, etc. into the EMI mode device the way, KB, MS by the appearance of the existing access key for operation, and a Dongle is required by another welding ID key, only through this ID key operation (nano dongle General No ID key)
2.4G Mouse EMI mode operation Methods
-
Power on while holding down the (L) + (M) + (R) keys for 5 seconds after release, Battery LOW LED will be turned on, into the EMI mode success 。
-
Scan Mode to enter test mode is the range of 2408 ~ 2474MHz (34ch) transmission frequency.
note : In the Scan Mode press the button (M) is a single channel into the 2408MHz frequency hopping, time hopping time 500ms -
Click the right (R), skip to the Modulation Frequency 2408MHz (± 500K), continuous transmission.
-
Click the right (R), skip to the Modulation Frequency 2440MHz (± 500K), continuous transmission.
-
Click the right (R), skip to the Modulation Frequency 2474MHz (± 500K), continuous transmission.
note: In the Modulation transmission mode, slide the wheel to do fine- tune the frequency 2408MHz ~ 2474MHz (± 500K)
note: In the Modulation transmit mode, press the button (M) may be circulating 2408MHz ± 500K), 2440MHz ± 500K, 2474MHz ± 500K three frequency -
Click the right (R), skip to the Modulation Frequency 2408MHz (± 500K), continues to receive.
-
Click the right (R), skip to the Modulation Frequency 2440MHz (± 500K), continues to receive.
-
Click the right (R), skip to the Modulation Frequency 2474MHz (± 500K), continues to receive.
-
Click the right (R), skip to the Non-Modulation Frequency 2408MHz (+500 K), continuous transmission.
-
Click the right (R), skip to the Non-Modulation Frequency 2440MHz (+500 K), continuous transmission.
-
Click the right (R), skip to the Non-Modulation Frequency 2474MHz (+500 K), continuous transmission.
-
Click the right (R), skip to the Non-Modulation Frequency 2408MHz (+500 K), continuous to receive.
-
Click the right (R), skip to the Non-Modulation Frequency 2440MHz (+500 K), continuous to receive.
-
Click the right (R), skip to the Non-Modulation Frequency 2474MHz (+500 K), continuous to receive.
-
Click the right (R), skip to the Non-Modulation frequency of 2408MHz, continuous transmission.
-
Click the right (R), skip to the Non-Modulation frequency of 2440MHz, continuous transmission.
-
Click the right (R), skip to the Non-Modulation frequency of 2474MHz, continuous transmission.
-
Click the right (R), skip to the Non-Modulation frequency of 2408MHz, continuous to receive.
-
Click the right (R), skip to the Non-Modulation frequency of 2440MHz, continuous to receive.
-
Click the right (R), skip to the Non-Modulation frequency of 2474MHz, continuous to receive.
-
And then click right-click (R) back to Scan Mode, the second step, starting again from here, a loop, as long as there is no exit test mode, it will have a loop down. Press the button(L) for the exit, exit back to normal state after the normal operation of the mouse.
2.4G Keyboard EMI mode operation Methods
-
Power on while holding down the ESC+Y keys for 5 seconds after release, Battery LOW LED will be turned on, into the EMI mode success 。
-
Enter the test mode Scan Mode is the range of 2408 ~ 2474MHz (34ch), frequency of transmission.
note: In the Scan Mode press the ~ key then enter the 2408MHz single- channel frequency hopping, time hopping time 500ms -
Click the Tab key skip Modulation Frequency 2408MHz (± 250K), continuous transmission.
-
Click the Tab key skip Modulation Frequency 2440MHz (± 250K), continuous transmission.
-
Click the Tab key skip Modulation Frequency 2474MHz (± 250K), continuous transmission.
note: In the Modulation transmit mode, press the + key or-key (non- numeric keys) to do fine-tune frequency 2408MHz ~ 2474MHz (± 250K)
note: In the Modulation transmission mode, press the `~ key can cycle 2408MHz ± 250K), 2440MHz ± 250K, 2474MHz ± 250K three frequency -
Click the Tab key skip Modulation Frequency 2408MHz (± 250K), continues to receive.
-
Click the Tab key skip Modulation Frequency 2440MHz (± 250K), continues to receive.
-
Click the Tab key skip Modulation Frequency 2474MHz (± 250K), continues to receive.
-
Click the Tab key, skip to the Non-Modulation Frequency 2408MHz (+250 K), continuous transmission.
-
Click the Tab key, skip to the Non-Modulation Frequency 2440MHz (+250 K), continuous transmission.
-
Click the Tab key, skip to the Non-Modulation Frequency 2474MHz (+250 K), continuous transmission.
-
Click the Tab key, skip to the Non-Modulation Frequency 2408MHz (+250 K), continuous to receive.
-
Click the Tab key, skip to the Non-Modulation Frequency 2440MHz (+250 K), continuous to receive.
-
Click the Tab key, skip to the Non-Modulation Frequency 2474MHz (+250 K), continuous to receive.
-
Click the Tab key, skip to the Non-Modulation frequency of 2408MHz, continuous transmission.
-
Click the Tab key, skip to the Non-Modulation frequency of 2440MHz, continuous transmission.
-
Click the Tab key, skip to the Non-Modulation frequency of 2474MHz, continuous transmission.
-
Click the Tab key, skip to the Non-Modulation frequency of 2408MHz, continuous to receive.
-
Click the Tab key, skip to the Non-Modulation frequency of 2440MHz, continuous to receive.
-
Click the Tab key, skip to the Non-Modulation frequency of 2474MHz, continuous to receive.
-
And then continue to click Tab key is another jump Scan Mode, the second step, starting again from here, a loop, as long as there is no exit test mode, it will have a loop down. Press ESC to exit, exit back to normal state after the normal operation of the Keyboard.
2.4G USB dongle EMI mode operation Methods
-
Power on while holding down the ID key for 30 seconds after release, Battery LOW LED will be turned on, into the EMI mode success 。
-
Enter the test mode Scan Mode is the range of 2408 ~ 2474MHz (34ch), frequency of transmission.
note : In the Scan Mode while holding down the ID key for 1 after release,into a second single-channel 2408MHz frequency hopping, time hopping time 250ms -
Click the ID key is to jump Modulation Frequency 2408MHz (± 500K), continuous transmission.
-
Click the ID key is to jump Modulation Frequency 2440MHz (± 500K), continuous transmission.
-
Click the ID key is to jump Modulation Frequency 2474MHz (± 500K), continuous transmission.
note : In the Modulation transmission mode, press the ID key long to do a second frequency tuning 2408MHz ~ 2474MHz (± 250K) -
Click the ID key is to jump Modulation Frequency 2408MHz (± 500K), continues to receive.
-
Click the ID key is to jump Modulation Frequency 2440MHz (± 500K), continues to receive.
-
Click the ID key is to jump Modulation Frequency 2474MHz (± 500K), continues to receive.
-
Click the ID key, skip to the Non-Modulation Frequency 2408MHz (+500 K), continuous transmission.
-
Click the ID key, skip to the Non-Modulation Frequency 2440MHz (+500 K), continuous transmission.
-
Click the ID key, skip to the Non-Modulation Frequency 2474MHz (+500 K), continuous transmission.
-
Click the ID key, skip to the Non-Modulation Frequency 2408MHz (+500 K), continuous to receive.
-
Click the ID key, skip to the Non-Modulation Frequency 2440MHz (+500 K), continuous to receive.
-
Click the ID key, skip to the Non-Modulation Frequency 2474MHz (+500 K), continuous to receive.
-
Click the ID key, skip to the Non-Modulation frequency of 2408MHz, continuous transmission.
-
Click the ID key, skip to the Non-Modulation frequency of 2440MHz, continuous transmission.
-
Click the ID key, skip to the Non-Modulation frequency of 2474MHz, continuous transmission.
-
Click the ID key, skip to the Non-Modulation frequency of 2408MHz, continuous to receive.
-
Click the ID key, skip to the Non-Modulation frequency of 2440MHz, continuous to receive.
-
Click the ID key, skip to the Non-Modulation frequency of 2474MHz, continuous to receive.
-
And then continue by clicking ID key in turn to jump Scan Mode, the second step, starting again from here, a loop, as long as there is no exit test mode, it will have a loop down under the power can only leave EMI mode.
2.4G USB dongle EMI mode For AP
- Model Scan Mode is the range of 2408 — 2474MHz (32ch), frequency of transmission.
- Mode2 Modulation Frequency 2408MHz (± 500K), continuous transmission.
- Mode3 Modulation Frequency 2440MHz (± 500K), continuous transmission.
- Mode4 Modulation Frequency 2474MHz (± 500K), continuous transmission.
- Mode5 Modulation Frequency 2408MHz (± 500K), continues to receive.
- Mode6 Modulation Frequency 2440MHz (± 500K), continues to receive.
- Mode7 Modulation Frequency 2474MHz (± 500K), continues to receive.
- Mode8 Non-Modulation Frequency 2408MHz (+500 K), continuous transmission.
- Mode9 Non-Modulation Frequency 2440MHz (+500 K), continuous transmission.
- Model° Non-Modulation Frequency 2474MHz (+500 K), continuous transmission.
- Modell Non-Modulation Frequency 2408MHz (+500 K), continuous to receive.
- Model2 Non-Modulation Frequency 2440MHz (+500 K), continuous to receive.
- Model3 Non-Modulation Frequency 2474MHz (+500 K), continuous to receive.
- Model4 Non-Modulation frequency of 2408MHz, continuous transmission.
- Model5 Non-Modulation frequency of 2440MHz, continuous transmission.
- Model6 Non-Modulation frequency of 2474MHz, continuous transmission.
- Modell Non-Modulation frequency of 2408MHz, continuous to receive.
- Model8 Non-Modulation frequency of 2440MHz, continuous to receive.
- Model9 Non-Modulation frequency of 2474MHz, continuous to receive.
- Mode20 single-channel 2408MHz frequency hopping, time hopping time 250ms
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be u sed in portable exposure condition without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>