Amazon Basics 12-Outlet Power Strip Surge Protector-Complete Features/Userr Guide

: June 5, 2024
: amazon basics

Table of Contents

Amazon Basics 12-Outlet Power Strip Surge Protector
Specifications
Introduction
CONTENTS
IMPORTANT SAFEGUARDS
INTENDED USE
BEFORE FIRST USE
OPERATION
INSTALLATION
CLEANING AND MAINTENANCE
Frequently Asked Questions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Amazon-Basics-12-Outlet-Power-Strip-Surge-Protector-
loog

Amazon Basics 12-Outlet Power Strip Surge Protector

Amazon-Basics-12-Outlet-Power-Strip-Surge-Protector-
img

Specifications

BRAND: Amazon Basics
VOLTAGE: 120 Volts
MAXIMUM SURGE RATING: 4320 Joules
ITEM WEIGHT: 2.2 Pounds
ITEM DIMENSIONS LXWXH: 12.2 x 5 x 1.29 inches
ELECTRICAL RATING: 120V, 15A
MAXIMUM POWER OUTPUT FOR ALL SOCKETS: 1800W
CORD LENGTH: 10ft
PROTECTION CLASS: class 1

Introduction

It Protects sensitive electronic devices such as computers, data lines, televisions, and other electronic devices from potentially harmful power surges. Active surge protection and grounded wiring are indicated by built-in lights. A fireproof MOV adds an extra layer of protection against surges and spikes. A 15Amp overload resettable circuit breaker is integrated with the power on/off switch. It is a Heavy-duty power cord with many outlets, sliding covers, and a back keyhole wall-mount

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included. When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following:

This product should not be used with aquariums, near water or any other source of moisture.
Do not open the housing for any reason. There are no user-serviceable parts inside.
To reduce the risk of electric shock- use only indoors.
Keep away from children.
Do not install this product if there is not at least 10 meters (30 feet) or more of wire between the electrical outlet and the electrical service panel.

CAUTION
Do not use the product in General Patient Care Areas or Critical Patient Care

Areas

Connect the product directly to a grounded power outlet only.
Do not exceed the maximum power output of the product.
Do not connect different extension cords in series

INTENDED USE

This product is intended for protecting the electronics from power surges or increases in voltage. This product is intended for household use only. It is not intended for commercial use.
This product is intended to be used in dry indoor areas only.
No liability will be accepted for damages resulting from improper use ar non-compliance with these instructions.

BEFORE FIRST USE

Check for transport damages.
Clean the product before first use.
Before connecting the product to the power supply, check that the power supply voltage and current rating correspond with the power supply details shown on the product rating label.

DANGER

Risk of suffocation! Keep any packaging materials away from children-these materials are a potential source of danger, e.g., suffocation.

OPERATION

Plug the product’s power plug into a standard 3-wire grounded 120 V- outlet.
To turn the product on, set the power switch to the RESET position. The “Protected and Grounded” indicators light up green.
Plug the equipment’s power plug including 2-wire devices) into the product’s outlets.
To manually turn the product off, set the power switch to the OFF position. All outlets stop providing power and both indicators go off.
After unplugging the equipment, close the sliding safety covers

WARNING
the “Protected” indicator goes off, the built-in surge protection is no longer functioning. Unplug all the connected devices and replace the product.

WARNING
the “Grounded indicator goes off but power is present, unplug all the connected devices and consult a qualified electrician to check your outlet’s wiring.

NOTICE
do not overload the product’s outlets. The product can accommodate a total equipment load of up to 15 A (1800 W) (whether plugged into a single outlet or spread out over multiple outlets). If the load exceeds 15 A, the built-in circuit breaker will trip and the outlets will stop providing power. In such case reduce the load by unplugging some devices and again set the power switch to RESET position.

INSTALLATION

The product can be installed on a wall using screws (not provided and wall mounting holes located on the back side of the product.

WARNING
Never drills into water pipes or power lines. Use a line locator if necessary.

CLEANING AND MAINTENANCE

WARNING
Risk of electric shock! To prevent electric shock, unplug before cleaning.

WARNING
Risk of electric shock! During cleaning do not immerse the electrical parts of the product in water or other liquids. Never hold the product under running water.

To clean, wipe with a soft, slightly moist cloth.
Dry the product after cleaning.
Never use corrosive detergents, wire brushes, abrasive scourers, or metal or sharp utensils to clean the product.
Store in a cool and dry place away from children and pets, ideally in original packaging Avoid any vibrations and shocks.

Frequently Asked Questions

Are the basic surge protectors from Amazon any good?
This low-cost surge protector is not recommended for safeguarding electronics. However, that is not a good recommendation. It only clamps the voltage at 800V, which may cause harm to some electronics if the surge lasts longer than a few seconds, and it only provides 790 joules of protection.
What does it imply if the light on my surge protector blinks?
Due to the gradual deterioration of the indicator light, the ubiquitous power strips used in every type of home or business have a propensity to flicker. Only power strips with neon lighting, not those with LED indications, have this problem. Because the light is so faint, it is most easily noticed in a dimly lit room.
What does my surge protector’s red light mean?
Your surge protector is providing surge protection for your devices if the red protection signal is on. If the red light goes out, the surge protector has been damaged by a power surge and a replacement should be ordered.
What does a surge protector’s reset button do?
Surge protectors shut down as a defense mechanism to protect themselves and your gadgets when there are large surges. If your surge protector has shut down due to a power surge, you’ll need to reset it in order to restore electricity.
What is the difference between a surge protector and a power strip?
You can plug many gadgets into a single wall socket using a power strip. A surge protector is a sort of power strip that is meant to withstand power surges and protect your equipment.
Is there a difference between certain surge protectors and others?
The best sign of increased protection is a higher joule rating. Choose a surge protector with a joule rating of 200 to 400 at the very least. A joule rating of at least 1000 is required for sensitive or expensive equipment, such as computers, displays, and audio/video equipment.
Is it better to have a red or green surge protector light?
The yellow light should always be on since it signifies that power surge protection is in place. The green light on the surge protector shows that it is grounded. Although it is not essential, you should ground the surge protector and turn on the green light for optimal protection.
What lights on a surge protector should be turned on?
Should the ground light on my surge protector be turned on (green)? Yes. The ground indicator light must be turned on. There is a problem with the AC outlet into which the CyberPower surge suppressor is plugged if the LED is not lighted.
Is it better to have a surge protector light on or off?
Yes. The surge light must be turned on. This means that the CyberPower surge suppressor is in good working order. If the light is not illuminated, the surge protector has been subjected to a catastrophic surge and must be replaced.
How can I tell whether my surge protector is functioning properly?
Examine the “Protection Present” or “Protected” LED on the front of the surge protector’s casing to see if the internal surge protection components are working properly. Your surge protector is ready to go and ready to protect you when the next power surge happens if it is lighted green.