BNproducts JMB-22 REBAR BENDER Instruction Manual
- June 5, 2024
- BNproducts
Table of Contents
BNproducts JMB-22 REBAR BENDER
**Instruction Manual**
Thank you for choosing our JMB-22 Rebar Bender
This manual covers the proper operation and maintenance.
Before operating, please read this manual carefully for important procedures and safety.
All technical data and drawings in this manual are consistent with the information on this product. As a result of revisions and other on going updates, the contents of this manual may be slightly different from the actual product. BN Products reserves the right to make changes at any time, without notice and without incurring any obligation, please understand.
The copyright of this instruction manual belongs to us. No reproduction is allowed without the written consent from BN Products-USA. All rights are reserved.
This manual is a permanent part of this rebar bender and should accompany the rebar bender if it is resold.
Please read this manual carefully to ensure the safe use of this bender. Failure to comply with the instructions in this manual may lead to accidents and injuries. Therefore, make sure to operate the machine in compliance with these instructions. We are not liable for any damage caused to the machine or injury to the operator resulting from unauthorized modification of the device or the use of parts that are not genuine.
Basic Specifications and Performance
Specifications
Feature Identification
- Power Switch
- Emergency Switch
- Operation Switch
- Footing Switch
- Footing Switch
- Angle Adjustment Handle
- Bar Adjustment Stopper
- Center Roller
- Moving Roller
- Spring Tension Bolt
Simultaneous Bending Capacity and Number of Bars
(refer to the front panel of the machine)
Installation and Work Preparation
Installation
- Install the machine on a level, even surface.
- If the ground is not level, use an auxiliary base capable of supporting the bender rigidly
Power Connection
- Power cable conductor must be at least 5.5mm2.
- Power cable length must not exceed 50m.
(If it exceeds 50m, use a cable of 8mm2 minimum.)
Work Preparation
-
Turn on the power switch. Set the Angle adjustment at about 135, and let the machine run idly for about 3 minutes.
(Warming up should be at least 5 minutes in winter.) -
Once warmed up, set the desired angle for bending.
-
Select the roller according to the size of the rebar.
Periodic Check and Maintenance
Precautions
- Do not exceed the machine’s capacity for simultaneous bending. If exceeded, machine failure may result.
- When bending rebars while holding them, watch out for your fingers and prevent accidents.
- Depending on the rebar material, it may fracture during bending, resulting in an accident. Therefore, keep your attention fully focused on the bending work.
- Ensure that no persons or objects are within the radius of the bending rebar.
- Since this machine uses electric power, rain or water may cause an electricity leak. Keep in a dry place or cover with a waterproof film.
- When moving the machine, check that the transportation handle is firmly fixed.
Repairs and Security
- Replacing the carbon brush – Be sure to isolate the power plug from the power source. Check the carbon brush for wear when the machine is not in operation. If the carbon brush in the motor, which is subject to wear and tear, is worn, the motor will lose power or even stop until the power is next turned on. In such cases, the carbon brush(es) must be replaced.
- On the motor inside the machine, unscrew the brush cap with a straight tip screwdriver, and remove the brush together with the spring (replace both of the brushes.)
- When replacing the rotating roller or fixed roller, clean up with a brush.
- Inspection and Security. Check that bolts and nuts are fully tightened from time to time.
- Dry the machine sufficiently after the rainy season or rainfall before operation
- If the rotating roller jolts when returning to its original position, adjust it by unscrewing the spring tension adjustment bolt. If it returns too slowly, tighten the adjustment bolt.
- The machine is ready for operation when the power indicator lamp lights up after power input and power switch. If the lamp is not lit, check the power cable connection.
- If the machine does not start up when the power lamp is lit, check the fuse or check the carbon brush in the motor for wear.
- In the event of other troubles, please call 800-992-3833
JMB-22 #7 REBAR BENDER: PARTS LIST
BN PRODUCTS-USA, LLC.
3450 Sabin Brown Road
Wickenburg, AZ 85390
800-992-3833
BN Products-USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>