Clarke CS300D Digital Electronic Safe Instruction Manual

OPERATION & MAINTENANCE
INSTRUCTIONS DIGITAL SAFE
MODEL NO: CS300D
PART NO: 7710180
LS0321

CAUTION: Do not keep the override keys inside the safe!

INTRODUCTION

Thank you for purchasing this CLARKE Digital Safe.
Before attempting to operate the safe, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you can look forward to the safe giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.
This guarantee does not affect your statutory rights.

SPECIFICATION

REPLACEMENT OVERRIDE KEY

A small label is located on the front of each safe with a key number. The number will start with either the letter “J” or “G” followed by several digits. This number must be registered with us in the event you require a replacement key.
Please complete the registration form at the back of this manual and send it to the address stated with the form. If you fail to register the safe we will not be able to provide you with a replacement key.
We recommend that in addition to sending the completed form you remove the label from the safe and fix it to the space below. Please retain this document for future reference.
Fix or record the key number here

BEFORE USE

OPENING THE SAFE FOR THE FIRST TIME

1. Remove the small plastic cover (B) on the front panel.

2. Insert the override key into the keyhole and turn it counterclockwise, at the same time, turn the doorknob (A) clockwise direction to open the safe.
   NOTE: Never keep the override keys inside the safe itself.

3. Replace the small plastic cover (B) with the front panel.

INSTALLING THE SAFE

The safe should be secured vertically to a wall, cupboard shelf, or to the floor using the expansion bolts (supplied).

• There are holes (8 mm) on the rear and bottom of the safe for securing to a wall or the floor.

INSTALLING THE BATTERIES
The safe requires 4 x size “AA” (1.5V) batteries.

1.  Open the safe.
2.  Remove the battery cover plate on the back of the door and install the batteries.
3. Ensure the batteries are fitted with the correct polarity.
4.  The use of alkaline batteries is recommended.

PROGRAMMING THE CODE

1.  With the safe door open and the batteries installed.

2.  Press and release the red button on side of the lock housing.
   • you will hear two beeps.
   • The yellow light will be on at the same time.

3. Enter the code you want to use (3-8 digits) as a combination.

4. Confirm within 15 seconds by pressing the letter “A” or “B”.
   • The safe “bleeps” twice and the yellow light will go off, your personal code is now set.

5. Test the safe using the new combination immediately. USING YOUR SAFE

TO OPEN THE SAFE

1. Enter your personal code followed by the letter “A” or “B”.
   • you will hear a beep and the green light on the front of the safe will light up.

2. Turn the doorknob in a clockwise direction to open the door within 5 seconds.
   • If you or an intruder uses the incorrect group of numbers, it will not open, if the incorrect combination is used 3 times consecutively, you must wait for 20 seconds before trying again.
   • If the incorrect combination is selected a further 3 times, you must wait approximately 5 minutes before trying again.

BATTERY REPLACEMENT WARNING

If the batteries are low, the red light (in the middle of the number panel) will illuminate.

MANUAL OVERRIDE

• See “Opening the safe for the first time” on page 3.

DECLARATION OF CONFORMITY

INTERNATIONAL
Fitzwilliam Hall Fitzwilliam Place. Dublin 2
DECLARATION OF CONFORMITY
This is an important document and should be retained.

We hereby declare that this product(s) complies with the following directive(s):
2014/30/EU: Electromagnetic Compatibility Directive.
2011/65/EU: Restriction of Hazardous Substances. (amended by 2015/863)
The following standards have been applied to the product(s):
EN 61000-6-3:2007+A1.2011. EN 61000-6-1:2009.
The technical documentation required to demonstrate that the product(s) meet(s) the requirement(s) of the aforementioned directive(S) has been compiled and is available for inspection by the relevant enforcement authorities.
The CE mark was first applied in 2009

Product Description: Digital Safe
Model number(s): CS3000. CS400D. CS600D
Serial/batch Number: N/A
Date of Issue: 09/03/2021
Signed:

INTERNATIONAL
Heimdall Street, Epping, Essex CM16 4LG
DECLARATION OF CONFORMITY
This is an important document and should be retained.

We hereby declare that this product(s) complies with the following UK legislation:
Electromagnetic Compatibility Regulations 2016.
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
The following standards have been applied to the product(s):
BS EN 61000-6-31007+,41.2011. BS EN 67000-6-7:2009
The technical documentation required to demonstrate that the product(s) meet(s) the requirement(s) of the aforementioned legislation has been compiled and is available for inspection by the relevant enforcement authorities
This product was placed on the market: in 2009

Product Description: Digital Safe
Model number(s): CS3000. CS400D. CS600D
Serial/batch Number: N/A
Date of Issue: 09/03/2021

Signed:

A SELECTION FROM THE VAST RANGE OF

| QUALITY PRODUCTS
AIR COMPRESSORS
From DIY to industrial, Plus air tools, spray guns, and accessories.
GENERATORS
Prime duty or emergency standby for business, home, and leisure.
POWER WASHERS
Hot and cold, electric and engine driven – we have what you need
WELDERS
Mig, Arc, Tig, and Spot. From DIY to auto/industrial.
METALWORKING
Drills, grinders, and saws for DIY and professional use.
WOODWORKING
Saws, sanders, lathes, mortisers, and dust extraction.
HYDRAULICS
Cranes, body repair kits, and transmission jacks for all types of workshop use
WATER PUMPS
Submersible, electric, and engine drove for DIY, agriculture, and industry.
POWER TOOLS
Angle grinders, cordless drill sets, saws, and sanders.
STARTERS/CHARGERS
All sizes for car and commercial use.|
---|---|---

PARTS & SERVICE: 0208 988 7400
Parts Enquiries Parts@clarkeinternational.com
Servicing & Technical Enquiries Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
INTERNATIONAL Hemnall Street, Epping, Essex CM16 4LG
www.clarkeinternational.com

IMPORTANT

In order to be able to obtain a replacement key.
Please detach and complete this safe registration form (see reverse), Then return it to:
Clarke International
Product Registration Department
Shrubland Road
London
E10 7RB

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>