Kaikutek K60168-M Dongle User Manual
- June 5, 2024
- KaiKuTek
Table of Contents
K60168-M DONGLE
USER MANUAL
Vision 1.0
Nov. 2021 (Initial Version)
Revision
|
Preliminary/Changes
|
Date
---|---|---
1.0| Initial Version| 2021/10/13
| |
| |
| |
| |
| |
| |
KaiKuTeK RESERVES THE RIGHT TO AMEND THIS DOCUMENT WITHOUT NOTICE AT ANY TIME. KaiKuTeK ASSUMES NO RESPONSIBILITY FOR ANY ERRORS APPEAR IN THE DOCUMENT, AND KaiKuTeK DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF KaiKuTeK PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, OR INFRINGEMENT OF ANY PATENTS, COPYRIGHTS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
Dongle overview
1.1 Introduction to Dongle
K60168-M Dongle is a development Dongle base on 60 GHz FMCW transceiver with 1
transmitter (TX) and 3 receivers (RX) of the K60168-M main chip. Power and
gesture commands/ sensing are provided via an external computer and a USB
Type-C interface.
1.2 Dongle features
- K60168-M in BGA196 package
- JMS580 for USB to 2 channel SPI interfaces.
- SPI flash for K60168-M boot-code
- Power supply by USB port 5V
- Type-C plug
Dongle Application
2.1 System connection
The Dongle can communicate with Windows OS PC and Android smartphones through
a Type-C plug for gesture commands/ sensing.
2.2 Dongle sensing notice
The K60168-M main chip is placed on the top side, thus the antenna radiation direction will be the KaiKuTeklogo side.
USB driver installation
3.1 USB connector
The K60C EV requires a micro-B to type-A USB cable.J20 should be tied close to
supply the whole power source
3.2USB Serial Bridge
The bridge controller is a JMicron’s JMS580, which is a USB 3.0 USB-Serial
bridge controller. This bridge offers an SPI interface.
3.3 MS580 driver installation
3.3.1 Install JMS580 driver:
3.3.2 In this EV board, JMS580 acts as a virtual COM (VCOM) port device.
Since the inbox driver of Windows 7/8/10 can support VCOM devices, a user does
not need to install any driver to use this EV board.
3.3 Hardware Manager
When a user connects the EV board to a PC, the hardware manager tab will
appear similar to the figure below.
Federal Communications Commission (FCC) Statement
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
15.21
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- For body-worn operation, this device has been tested and meets FCC RF exposure guidelines. When used with an accessory that contains metal may not ensure compliance with FCC RF exposure guidelines.
15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference and
- this device must accept any interference received, including interference that may cause undesired operation of the device.
Copyright © 2020 KaiKuTeK Inc. All rights reserved.
Confidential Information
Headquarters:
KaiKuTeK TECHNOLOGY INC.
9F, No.3-2, Park St., Nangang Dist.,
Taipei City 115, Taiwan, R.O.C.
TEL: 886-2-26558953, 26558956
FAX: 886-2-26558955
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>