Zykronix Milano XL 15.6-Inch Touch Panel Installation Guide
- June 5, 2024
- Zykronix
Table of Contents
Zykronix Milano XL 15.6-Inch Touch Panel
Included in the box
- 1ea Device
- 1ea Mounting bracket
- 4ea Mounting screws
Introduction
To install the device you will also need one of the following electrical junction boxes or low-voltage brackets.
Important safety instructions
Read, understand and follow ALL safety and installation instructions included
in this manual. Failure to follow the included documentation may damage the
product and will void the manufacturer’s warranty. Follow ALL installation
guidelines included with the product. Installation of the product in high
humidity environments, in close proximity to heat sources and/or
non-recommended locations, WILL impede, interfere and/or damage the intended
operation of the product. Only use attachments and accessories which have been
specified for use by the manufacturer. The use of abrasive, liquid or solvent-
based cleaning fluids WILL damage the product. Product Servicing may ONLY be
completed by authorized or certified service centers & personnel. For a
complete list of product servicing options, please follow the instructions
included in the product documentation and/or contact the original manufacturer
for details. This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Device – Overview
Planning the installation
The device is designed to be wall-mounted in either Portrait or Landscape
orientation, or on the tabletop with a stand.
The device requires a minimum mounting depth of 1”(2.45cm) from the wall surface to the room for cable/s. Power may be supplied by Power Over Ethernet (PoE) or by a 24V DC power supply (not included). PoE connecting must meet the IEEE 802.3af standard. Direct power connecting via a 24V DC external power supply requires a minimum current output of 1A. The device connects to the local network via a hard wired Ethernet connection. Or connecting with WiFi in the case of the units with WiFi function.
Installing the device
-
Mounting height
The recommended mounting height for the device is 57”- 65” (145 cm -165 cm) from the finished floor to the center of the unit. -
Landscape/Portrait mounting
-
Installing the device mounting bracket
The device package includes a stainless steel mounting bracket that MUST be used for installation. Please note the mounting bracket in the box is designed for the US standard 2-gang and Hubbell 2-gang electrical box. You can order additional stainless steel mounting brackets for UK or European electrical boxes. Verify that the bracket is level before tightening the captive screws on the device. (US mounting bracket included in the box Part No.:84-900-0000-00) -
Connecting the device to power
The device is designed to be powered over the Ethernet connection (PoE) or by connecting a 24Vdc power supply (not included), but not both. If both the PoE and a 24Vdc power supply are connected, the device will draw power from the 24V DC source.
PoE Connection
PoE connection requires IEEE 802.3af standard. Utilize a network switch or PoE injector that meets this standard. Connect the device using a standard T568A or T568B Ethernet cable from the network switch to the LAN/PoE jack on the back of the device. -
24V DC Power Supply
You can provide power locally or remotely to device by utilizing a 24V DC power supply (not included). Please note that running the wire through the wall in accordance with local codes when powering locally. If powering remotely, please ensure to use wire of adequate gauge for the length of the run. Please use approved 24V DC power supply.
Verify the polarity of the barrel connector on your power supply before connecting it to the device. The center pin of the device power connector is positive and the outer ring is negative. If the wire is extended, please ensure that the routing is in compliance with local codes.
Plug the connector into the device DC jack on the back of the device. -
Mounting the device
- Loosen the captive screws of the unit first. Screws should not be moved apart from the unit. Please meet the indicated line.
- Align the mounting frame hooks with the mounting slots and gently pull the unit down the mounting bracket. Make sure the mounting hooks are properly engaged.
- To complete the installation, tighten the 2-captive screws on the bottom part of unit, to secure the device on the mounting bracket.
- For Portrait orientation, rotate the mounting bracket and 90 degrees in a counterclockwise direction before installation.
Removing the device
Using a precision Philips head screw driver to loosen the 2-captive screws on
the device, then slightly pull straight up from the mounting frame to
disengage the unit.
Setting screen orientation
On the touch panel setup screen, select Landscape or Portrait display modes.
Press Start device to launch the user interface.
To change orientation:
- Remove power from device.
- Re-apply power to device.
- Select landscape or portrait orientation.
Thank you for including the device as part of the user interface strategy for
your customer. The device has been designed to provide years of trouble free
operation when wired and installed properly. The device is designed for
installation in low humidity indoor environments and should never be installed
outdoors or in high humidity areas. Any changes or modifications not expressly
approved by the grantee of this device could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for satisfying
RF exposure compliance.
Canada, Industry Canada (IC) Notices
This device complies with Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>