OUTDOOR MASTER OM BT01 Wireless Hemet Drop-in Headphone Instructions
- June 5, 2024
- OUTDOOR MASTER
Table of Contents
Instructions for use
Product: Headphone
MODEL: OM BT01
Parameter
Support: A2DP, hands-free, ACVRCP profile
Input DC: 5V
Charging time: 2 hours
Call time: about 3 hours
Play time: about 3-4 hours
Impedance: 32Ω
Bluetooth distance: 10m
Material: ABS + PVC
MASTER OM BT01 Wireless Hemet Drop-in Headphone
-
Turn On:
turn On the device and press the On button for 3 seconds, You will hear the voice Power on, ready to pair, after the red light flashes, the white light turns on (every 0.5 seconds); after the pairing is successful, the white light turns on (every 3 minutes). -
OFF:
when the device is turned on, hold the ON button for a longer period of time 3 seconds, You will hear the voice – Power off, The red light flashes, and the rear light is off. -
Switch:
Press and hold for 3 seconds, power on to pair the connected device, or connect to a new device, you will hear a Single “Beep”, the red light is on, and the white light is on after the pairing is successful (every 3 minutes) -
Pair new device
Press and hold for 4 seconds, power on to pair the new device, and you will hear a Single “Beep”, after the red light flashes, then the white light turns on (every 0.5 seconds); after the pairing is successful, the white light turns on (every 3 minutes) -
Play / Pause
Click the button, play: white light is on (every 3 minutes). Pause: white light is on -
Connect the call, hang up
Click the button, the white light will turn on (every 3 minutes). -
Reject the call
Long press for 3 seconds -
Volume up/previous song
Volume up: click the button, you will hear Single “Beep” Previous song: Long press the button for 3 seconds Volume down/Next song Volume down: click the button, you will hear Single “Beep” Next song: Long press the button for 3 seconds -
Low battery warning
If it is lower than 3.3V, it will be turned off after 2 reminders (every 3 minutes), the red light will flash, and you can hear the voice -
Charge
Shut down, charge-red light is on during charging, white after full charge, etc. -
Disconnect
After 5 minutes of disconnection, it will automatically shut down, the red light flashes, and the backlight is off.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure compliance statement:
This device has been evaluated to meet the general RF exposure requirement
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>