Bytech Ny AUBE140 True Wireless Earbuds User Manual
- June 5, 2024
- Bytech Ny
Table of Contents
Bytech Ny AUBE140 True Wireless Earbuds
These True Wireless Earbuds can be used alone (one earbud) or as a pair.
Please note that phone calls can be used with one earbud or both earbuds. If
you use both earbuds the call will be in stereo.
SPECIFICATIONS
- Simulated Stereo
- Bluetooth V 5.0 (only support BDR+EDR)
- Sound Output: 2mw
- Input Power: 5V DC 1A
- Earbud Battery: 45mAh Per single
- Charging Case Battery: 350mAh
- Charging Power: 5V/100mA
- Transmission distance: 10m
- Frequency: 20HZ-20KHZ
- Calling time: 2 hours
- Music time: 2 hours
- Standby time: around 150 Hours
PACKAGE CONTENTS
- Charging case
- 2 true wireless earbuds
- 6″ Micro USB charging cable
- Instruction Manual
PAIRING
- Single earbud connection: Turn on either earbud by holding the power button down, red and blue lights are now flashing, Now search Bluetooth connections on your device and TB-BE-140 will be listed; choose it. After successful connection, you can listen to music or make a phone call.
- TWS Stereo (Dual Ear connection): Turn on both earbuds by holding their power buttons down. Red and blue lights are now flashing. Now search Bluetooth connections on your device and TB-BE-140 will be listed; choose it. After successful connection, you can listen fo music or make a phone call.
BLUETOOTH USAGE
Phone call
When connected to a device capable of making and receiving phone calls you can
short press either earbud button to answer an incoming call.
You can also double press any button to redial the last outgoing number.
Listening to music:
When the earbuds are turned on and connected to the phone or Bluetooth-enabled
Bluetooth device you can open the player and listen to music. In the process
of listening to music, press the button once to pause the current music, and
again to play the music Which has been paused for a short time.
Power off:
Long press the function button to turn the earbuds off. Each one needs to be
powered off individually.
Charging
Insert the earbuds into the charging case and connect a USB charger to the
Micro USB Port at the back of the charging case. The red LED will flash
while charging and will glow solid red when fully charged.
If you open the case you will see a red glow from the earbuds, this means they
are charging. Once fully charged they will glow blue until removed from the
case.
If the earbuds batteries become depleted, you can insert them into the charge
case and press the button on the charge case (if the charge case has a full
charge). The LED will glow blue and will begin charging the earbuds. When
charging has been completed the blue LED will turn off.
Please note:
-
Do not abuse this product, and do not squeeze it between heavy objects. Keep them far away from high temperature and humidity & away from and other high frequency transmitter equipment, this will affect the local signal reception, resulting in sound breakup and distortion or disconnection.
-
This product can be connected to any Bluetooth-enabled device.
-
Please note that while using this product, if for any reason you move out of the range of the device you are listening to, the earbuds will disconnect. When you are back in range you may need to perform the pairing procedure again as this depends on battery life. If the earbuds are powered on and are disconnected from a Bluetooth device for more than 3 minutes they will power off.
-
Dust net
-
Multifunction button
-
Mic
-
headset charging pori
-
headset charging port
FCC ID:2AHN6-AUBE140
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly approved could avoid
the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. Bytech NY INC. warrants this product to be free from
defects in materials and workmanship to the original purchaser for a period of
12 months from the original purchase date. Bytech’s responsibility with regard
to this limited warranty shall be limited solely to repair or replacement as
its option, of any product which fails during normal consumer use. This
warranty does not extend to damage or failure which results from misuse,
neglect, accident, alteration, abuse, improper installation or maintenance. At
any time during the 12 month period following the purchase, the product fails
due to defects in material or workmanship, return the defective product (with
freight prepaid) with proof of purchase. Please include $5.00 for return
shipping and handling.
SUPPORT@GBYTECHINTL.COM
2585 WEST 13TH STREET,
BROOKLYN, NY 11223
Bluetooth® is a registered trademark of SIG, Inc.
All Trademarks and copyrights are the property of the respective companies
*Photos are for illustration purposes only