Shenzhen Mengxiang Technology D35MH8L Rechargeable Bluetooth Speaker User Manual
- June 5, 2024
- Shenzhen Mengxiang Technology
Table of Contents
Shenzhen Mengxiang Technology D35MH8L Rechargeable Bluetooth Speaker
WARNING!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER ON THIS
SPEAKER THERE ARE NO USER SERVICEABLE PARTS NSIDE. REFER ALL SERVICING TO
AQUALIFIED TECHNICIAN
- Read these instructions thoroughly before using this item.
- Keep these instructions for future reference.
- Heed all warnings.
- Follow all instructions.
- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not store or operate this product near any liquids.
- Clean only with a dry cloth.
- Do nat store or operate this product near any heat saurces such as radiators, heat registers, stoves, or other apparatuses (including amplifiers) that produce heat &-Do nat defeat the safety purpose of the polarized or grounding-ype plug. A polarized plug has two blades with one wider than the other.
- A grounding plug has two blades and a round grounding prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit your outlet, consult an electrician far the replacement of the obsolete outlet
- Protect the all wires connected to this unit from being walked on or pinched, particularnly plugs and the point where they exit from the unit. Wmen removing the cord from the power outlet, remove it by holding the plug not by pulling the cord.
- Unplug the unit during lightning storms or when unused for long periods of time.
- When wiring this unit and all other equipment used in connection to this unit make sure that all of your equipment is turned OFF
- Once installation and wiring is complete power on all your equipment with the volume and level controls turned DOWN. Once all the equipment is ON slowly ralse the volume or leval controls to their proper positions.
- When grounding this unit, be sure to do so correctly, so as not to defeat the buit-in grounding in this unit.
- Before placing, installing, rigging, or suspending any product. inspect all hardware, SUspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, coroded, deformed, or nonoad rated oomponent could significantly reduce the strength of the installabon, placement or array. Any such condition severely reduces the satety of the installation and should be immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term, unexpected overloading. Never excBed the rating of the hardware or equipment.
- Consult a licensed, Professional Engineer regarding physical equipment installation. Ensure that all local, state and national regulations regarding the safety and operation of equipment are understood and adhered to.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in ay way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Introduction
Congratulations and thank you for your purchase of this Technical Pro professional rechargeable loudspeaker. To get the most from your speake, it is recommended that you review all of the infomation provided in this instruction manual before operating this equipment. If you’ve spent any time at all in professional audio, you know the name Technical Pro and what it stands for- incredible performance & sound, and the ultimate in reliability under harsh conditions. And now, Technical Pro offers the same technology in a series of portable loudspeakers bringing more of what sets Technical Pro apart from all others.
In the box:
Installing the battery:
The battery for the remote control (1 CR2025 Lithium Battery) is included. To
replace the battery, push and slide out the battery door on the remote
control. Replace the battery with a new CR2025 battery with the positive (+)
polarity facing up. Slide the battery door back in to the remote control.
NOTE: The soundbar remote is packaged with a plastic protection tab.
Before operating the remote, gently pull the protective tab extending out of
the remote control’s battery door.
SIDE PANEL
- [ IR J:Infrared remote sensor
- [ POWER/LED ]button:Press and HOLD DOWN this button to power the speaker ON and OFF. Tap the button for LED light control The light order is yellow, cyan, purple, blue, red, green and white”
- [ MODE Jbutton:Press this button switch input modes
- [ # ]button:Press this button to decrease the volume. Press and HOLD DOWN for 3 seconds this button to go to the previous track.
- button:In Bluetooth Mode, Press this button to play pause the audio. Press and HOLD DOWN for 3 seconds this button to disconnect to the Bluetooth device.
- button:Press this button to increase the volume. Press and HOLD DOWN for 3 seconds this button to go to the next track.
- AUX }:AUX Input LED indicator light
- OPTIARC ]:Optical/ ARC Input LED indicator light
- [ BT
- LED will be flashing under pairing process, and stays on when it is paired. Bluetooth Input LED indicator light
BACK PANEL
-
Power Input (DC IN)
-
AUX Input
-
OPTICAL Input
-
ARC Input
-
POWER] Key: Standby Power ON/OFF
-
[INPUT] Key: Switch modes
-
| Key: Skip to previous track
-
[ ] Key: Play/pause music
-
[ ]Key: Skip to next track
-
TREBLE-] Key: Decrease treble volume
-
[BASSH Key: Decrease bass volume
-
TREBLE+] Key: Increase treble volume
-
VOL-] Key: Decrease volume
-
[BASS+] Key: Increase bass volume
-
[VOL+ ] Key: Increase volume
On the rear of the soundbar there is a speaker output connector. Use the speaker output connectors to wire the soundbar to the subwoofer. The soundbar should be powered off and proper polarity should be maintained when making these connections. The picture of the rear of the subwoofer should show the speaker wires can be removed.
Mounting the speaker:
- Measure a width of 25.5 inches on the wall.
- Mark the position of the mounting screws on the wall using a pencil.
- Drill the supplied screws directly into the marks that you have made on the wall and leave approximately 0.3 inch length to hook the Wireless Sound Bar.
- Put the Wireless Sound Bar onto the mounting screws. Make sure they are firm and stable.
Operation process
- Connect the DC power cord into a wall socket.
- Turn the speaker on by pressing and holding down the Power button on the speaker or tapping the power button on the remote control.
Bluetooth Connection Method for Android system:
-
1. Go to SETTINGS> BLUETOOTH(make sure Bluetooth is turned ON)
- When your Bluetooth enabled device finds the speaker, select ” SBSUB” from the list of found devices. When succeeding pairing, you will hear ” deng deng”.[ BT] Bluetooth indicator light appears normally on. When playing the music, the blue led light will light always on.
Bluetooth Connection Method for iphone IOS system:
- Go to SETTINGS> BLUETOOTH(make sure Bluetooth is turned ON)
- When your Bluetooth enabled device finds the speaker, select” SBSUB from the list of found devices. When succeeding pairing, you will hear ” deng deng”[BT] Bluetooth indicator light appears normally on. When playing the music, the blue led light will light always on.
AUX Input Operation
Connect the audio output from an audio device to the AUX input on the back
panel of the SBSUB. Tap the MODE button to set the input to AUX. The AUX LED
indicator will illuminate red when the unit is set to AUX mode.
Optical Input Operation
Connect the optical output from an audio device to the optical input on the
back panel of the SBSUB. Tap the MODE button to set the input to OPTIARC. The
OPT/ARC indicator will illuminate red when the unit is set to optical mode.
ARC Input Operation
Connect the ARC output from an audio device to the ARC input on the back panel
of the SBSUB. Tap the MODE button to set the input to OPT/ARC. The OPT/ARC
indicator will iluminate blue when the unit is set to ARC mode.
ARC mode operation
- Please insert one connection port of ARC fiber into the [ARC] fiber input jack first, and then insert another connection port into the socket of media playback device.
- Press the [ MODE ] button on the speaker or the [ INPUT ] button on the remote control. When [OPT/ARC ] optical fiber indicator lights up blue light,then enter the ARC state.
- Volume control operation
- Short press the [ ]button on the speaker or the [VOL-] button on the remote control to reduce the volume.
- Short press the[ ] button on the speaker or the [VOL+] button on the remote control to increase the volume.
- Press the [TREBLE-J button on the remote control to reduce the treble volume.
- Press the [TREBLE+] button on the remote control to increase the treble volume.
- Press the [BASS-] button on the remote control to reduce the bass volume.
- Press the [BASS+] button on the remote control to increase the bass volume.
Skipping and play/pause songs operation
- Long press the ]button on the speaker or the [i]button on the remote control to skip to the previous song.
- Long press the [ ] button on the speaker or the [ ] button on the remote control to skip to the next song.
- Short press thelJbutton on the speaker or the remote control to play or pause musi.Long press the [ Jbutton to disconnect Bluetooth.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- This device must accept any interference received, including interterence that may cause undesired operation.
FCC Requirement
changes or modifications not expressly approved by the party responsible for
compliance could void the user s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.