mware MW809 Android TV Box User Manual

mware MW809 Android TV Box

Chapter 1 Overview

Appearance and interface

BT VOICE REMOTE

2| VOICE
3| BACK
4| HOME
5| APPS
6| UP
7| DOWN
8| LEFT
9| RIGHT
10| OK
11| MENU
12| PAUSE/PLAY
13| STOP
14| VOL-
15| VOL+
16| TELEVISION
17| TV GUIDE FOR EPG SECTION
18| SETTINGS

How to pair bluetooth?

• Press”Settings”button in launcher;

• Select “Remote&Acccessories”,press”OK” button searching for accessories;

• Press “OK” and “VOL-” at the same time about 4 seconds until the red LED will flash quickly;

• Press”OK”on bluetooth device name “R18B-P” option to enter“pair mode”
  Noted: if paired successful ,LED will be off; otherwise,the LED will be always flashing.

• After the connection is successful, you can choose”unpair” on “R18B-P” option.

Chapter 2 Initial configuration

Standard UI interface

• Power on, enter into main menu.
• Click ”Welcome/language/Resolution/Screen Zoom/Network.
• Click ”Open Android Setting Menu”, or “Settings” on remote, to access the Set-top box Settings menu.
• Login with Username and Password to access the TV service.

Apps

Select ”Settings”->”Apps”->”See all apps” for opening or delete other apps.

Chapter 3 Local media play

Select “File Browser” from apps->”Open”.
Select “Local Disk” or “USB” driver, press ”OK” button to enter.

Click the video, an option menu will pop up. Select your favorite video player to start playing video.

Click the music, an option menu will pop up.
Select your favorite music player to start playing music.

Click the photo, an option menu will pop up.
Select your favorite photo player to start playing photo.

Chapter 4 App Installer

About AppInstaller

About multi-screen communication

DLNA

• Click “Media Center” in Apps list.
• Turn on DLNA DMP” and “DLNA DMR”.
• Turn on DLNA in your android mobile device.
• Start playing the video, music and photo in your android mobile device.

Chapter 5 Settings

You can use setting to re-configure your network, display, language and etc.

Network &Time settings

Wifi Settings

• Network-> Wi-Fi/Ethernet, by “IP settings: DHCP”, when plug ethernet cable, ethernet settings will display “Connected”.
• If select “Static IP”, click “static” in IP settings, revise address in IP address bar, network gateway bar and DNS bar, click “Save”.

Time Settings
Select ”time and date” and ”Time Zone from Settings.

**Sound settings

**

System sounds
The standard setting is switch on.

Surround sound
Click “Surround sound”, there are (Auto/Always/Never) 3 options for choosing.

Language settings

OSD language settings
Click “Language Setting”, select the language as OSD language from language list, click “ok” to save and back.

Input method settings
Click “Input Settings”, input method from the list, click “OK” to save and back, then you can use new input method.

System upgrade

Local Update

• Press “Settings” at remote, click ”OTA Upgrade”.
• Select “Local Update”, click ”OK” to enter.
• Click “Select” button, select the new software,
• Select “Wipe Data” and “Wipe Media”.
• Click ”Update” to start update.

System information

FCC WARNING

Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment of Wireless Router should be installed and operated with minimum distance 20cm between the radiator & your body.
The remoter can be use without any restrictions

Troubleshooting

Check fuse
Network doesn’t work| Network cable not connected or bad network cable

Wi-Fi not connected wifi

| Connect/replace network cable Check Wi-Fi account/setting
No picture or sound| HDMI/AV is not selected on your

TV

| Reduce to another channel
No sound distort| Volume off

Speaker not connected

The audio codec may not be supported

| Adjust the voice volume Check Speaker connection Refer to the user manual
No response to remote| Receiver off Handset not aimed correctly Front panel obstructed

Hand set batteries exhausted

| Aim handset at front panel Check for obstructions

Replace handset batteries

USB can not be read| USB driver format not compatible or Broken USB Large file in USB driver to

slowly read USB

| Replace USB driver Remove large file in USB
Video playing abnormal| Video source is abnormal Network abnormal

Video codec may not supported

| Change video source

Check Wi-Fi or Ethernet status Refer to user manual

Specification

8G EMMC FLASH

OS| ANDROID 9.0
DECODER VIDEO DECODER

AUDIO DECODER PHOTO DECODER VIDEO FORMATS

|

4K2160P 60FPS H.265,MP@L4.0,Main10@L5.1 MP3,AAC,HE-AAC,WMA,RM,FLAC,Ogg JPG,JPEG,MJPEG,PNG

MPEG2,MPEG4,H.264(AVC),H.265(HEVC),VC1,WMV,VP9,MKV

,MPG,MPEG,DAT,AVI,MOV,ISO,MP4,RM,JPG

CONNECTION

MAIN POWER CABLE DATA PORT

HDMI OPTICAL AV

ETHERNET

|

FIXED TYPE

USB 2.01/USB3.01/ TF X1 HDMI OUTPUT x1

SPDIF x1

AV OUTPUTx1 RJ45x1

POWER SUPPLY INPUT VOLTAGE

POWER CONSUMPTION

|

12V/1A MAX. 12W

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>