Guangzhou Fcard Electronics FC-8300T Dynamic Face Recognition Access Controller User Manual
- June 5, 2024
- Guangzhou Fcard Electronics
Table of Contents
Ford Electronics FC-8300T Dynamic Face Recognition Access Controller
User Manual
FC-8300T
DYNAMIC FACE RECOGNIT10 ACCESS CONTROLLER
Metal Body, 20,000 Faces, 200,000 Records 5.5-Inch IPS Full-View And HD
Display Screen
20,000 Faces
HD Display Screen
High-Speed Identification
FUNCTION
Multi-Function List 
FORD
Intelligent Dynamic Face Access Controller
IPS Full-View And High-Definition Display Screen, Metal Body, Waterproof&Smog-
Proof, Can Be Used In Outdoor And Strong Light Environment.
TEMPERATURE DETECTION
The Infrared Array Body Temperature Sensor-
Temperature Records Mask Identification
No Entry With High Temperature
SCREEN
5.5-Inch IPS Full-View And HD Display Screen
High-Definition Display Screen, The Effect of Display Much More Clearer
Screen Dormancy, Screen Protection, High-Speed Recognition Wake-Up Function
IDENTIFY
0.5 Second High-Speed Identification
Accuracy Rate: 99.9%
360-Degree Biometrics Liveness Recognition, Identification Speethc,≤0.5S
| ≤0.5S | 99.9% | 2 Mega Pixel | 360° |
|---|---|---|---|
| High-Speed Identification | Recognition Accuracy Rate | HD Camera | Liveness |
Detection
CAMERA
2 Mega Pixel HD Binocular Camera
2 Mega Pixel Infrared Liveness Detection Camera Wide Dynamic Camera, No
Distortion, Double Synchronization, Global Exposure
RECOGNITION
Multiple People Simultaneous Recognition
1: N / 1:1 Can identify four people at the same time
20,000 Faces Capacity
(Can Be Extended 30,000-50,000 Faces )
200,000 Records 8G EMMC Storage 1GB DDR3 Memory
| 
---|---
Wide Dynamic Strong Light Suppression Wide dynamic 2 million HD camera
Not affected by strong light
| 
---|---
PRODUCT DETAILS
Details determine quality
metal quality, each product is an ingenuity
01 Body Temperature Detection Sensor
Can quickly recognize the people’s temperature| 
|
2. HD Binocular Camera
High-Speed Identification, Liveness Detection Wide Dynamic Strong Light
Suppression (Independent ISP Processing)
---|---|---
3. HD LCD Display Screen 5.5-Inch IPS Full-View And HD Display Screen ( 1280x
720 )| 4.Two USB Communication Port
Can insert USB disk to import data Can use U disk to upgrade and backup data
5. Mifare Card Reading Function Built-in card reading module, support Mifare
card, CPU card, ID card and so on| 6.Voice Prompt Function Opening door prompt
Alarm Prompt
Product Parameter
Model
FC-8300T Dynamic Face Recognition Access Controller| Body Material
Zinc Alloy Body
---|---
Working Voltage
5.5-Inch IPS Full View HD Screen| CPU
4CoreA7 1.2GHZ
Storage Capacity
1GB DDR3 + 8GB EMMC| GPU
MAL400 II
Communication WAY
(WIFI Communication can be ordered)| Operation System
LINUX
Camera
Wide Dynamic Binocular 2 million HD Camera| Liveness Detection
Support
User Capacity
20000 Faces + 20000 Cards| Records
200,000 Records
Recognition way
1: N/ 1:1| Identification Speed
≤0.5s
Wiegand Function
One Group of Wiegand Input/Wiegand Output (26/34| Working Humidity
10%-90% RH
Size
232x88x25mm| Weight (Manual Measurement)
0.5KG
Free Docking Platform
Support Docking Platforms, Provide SDK
Support Online Upgrade/Secondary Development
Application
Intelligent Community Passage System, Office Building Hall Corridor Management
System, Site Labor System, Club Membership Management System, Scenic Spot
Ticket System, etc.
Wiring Diagram
Wiring Requirements:
- AC220V power wire: recommend using 3×1.0mm (or above) wires to prevent electricity leakage. The ground wire of the power wire is recommended to be grounded.
- Electric lock wire: must use 2×1.0mm (or above) wire, the maximum length of the cable shall not exceed 50 meters.
- TCP/IP communication wire: please use standard network cable, the maximum length of the cable shall not exceed 100 meters.
- Door sensor and exit button wire: recommend using 2X0.5mm (or above) wire, the maximum length of the cable shall not exceed 100 meters.
REMARK
- Power on, locki (electric bolt lock or electromagnetic lock) correct connection: the positive electrode of the electric lock connects to NC of the output port of the controller. The negative electrode of the electric lock connects to the GND of the power supply. The COM of the controller connects to +12V of the power supply.
- Power on, unlocked ( electric control lock or electric lock port) correct connection: the positive electrode of the electric lock connects to NO of the output port of the controller. The negative electrode of the electric lock connects to the GND of the power supply. The COM of the controller connects to +12V of the power supply.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>