LG SBWAC03 RF Module User Manual

: June 5, 2024
: LG

****

LG SBWAC03 RF Module

LG SBWAC03 RF Module product

Features

LGSBWAC03 is the small size and low power module for IEEE 802.11ac wireless LAN & BT5.0 + HS. ETWCFMBC02 is based on Mediatek MT7663BUN solution.

IEEE 802.11 a/b/g/n/ac
Bluetooth 5.0+ HS , BLE.
Size : 68.0mm x 30.0 x 7.35 mm.
Two stream spatial multiplexing up to 300Mbps(802.11n) / 867Mbps(802.11ac)
Use on-chip OTP One Time Programmable.
Host Interface : USB2.0 WLAN & BT.
This model is using the common USB2.0 to control WLAN and BT.
Security : WAPI, WEP, WPA, WPA2, WMM, AES, TKIP, CKP.
Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB.

Picture of Product

Installation Manual

Install the module like below in the back of the TV

Block Diagram

LG SBWAC03 RF Module 2

Absolute Maximum Ratings

Caution
The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device.

Parameter	Min	Max	Unit
Storage Temperature	-20	+80	℃
Storage Humidity (40℃		90	%

Other conditions

Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. Store the modules where the temperature and relative humidity do not exceed 5 to 40℃and 20 to 60%. Assemble the modules within 6 months. Check the soldering ability in case of 6 months over.

Operating Conditions

LG SBWAC03 RF Module ll

Standard Test Conditions

The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance.

Ambient condition

Temparature 25 ±5℃
Humidity 65 ±5%

Power supply voltages

Input Voltage VDD_3.3V
Supply Voltage 3.135 ~ 3.6V

Pin Description

Pin No.| Pin Name| I/O| Pin Description|
---|---|---|---|---
1| VCC| I| VDD 3.3V
2| D-| I/O| USB Communication signal USB DN
3| D+| I/O| USB Communication signal USB_DP
4| GND| –| GND
5| WOWL| O| Wake On WLAN
6| VCC| I| VDD 3.3V
7| RESUME| I| SUSPEND RESUME
8| GND| | GND
9| RESET| I| Bluetooth device wake up option

10

|

WOBLE

|

O

| Host wake up.

Signal from Wi-Fi module to the host

11| GND| | GND
12| VCC| | VDD 3.3V

LG SBWAC03 RF Module 3

Outline Drawing

LG SBWAC03 RF Module 4

Packing Information

LG SBWAC03 RF Module 5

LG SBWAC03 RF Module 6

FCC Statement

FCC Part 15.19 Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

FCC Part 15.21 statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Responsible Party Information Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information.

Responsible Party

U.S. Contact Information.
LG Electronics USA.
1000 Sylvan Avenue Englewood Cliffs.
New Jersey, United States, 07632.
Telephone number or internet contact information.

Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual v01 > List of applicable FCC rules
This module has been granted modular approval as below listed FCC rule parts.

FCC Rule parts 15C(15.247 / 15.407
Summarize the specific operational use conditions. The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed.

RF exposure considerations
The module has been certified for integration into products only by OEM integrators under the following condition. The antenna must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator antenna and all persons at all times. The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

Mobile use
As long as the three conditions above are met, further transmitter testing will not be required. OEM integrators should provide the minimum separation distance to end.

Antennas list

Frequency Band| Dual Band Ant1| Dual Band Ant

2

| BT Ant

(2402-2480)

---|---|---|---
2.4G (2412-2472)| 1.19 dBi| 1.50 dBi| 1.19 dBi
UNII-1 (5180-5240)| 0.05 dBi| 1.42 dBi|
UNII-2A (5260-5320)| 0.98 dBi| 1.45 dBi|
UNII-2C (5500-5720)

without 5600-5650

| 1.41 dBi| 1.37 dBi|
UNII-3 (5745-5825)| 1.44 dBi| 1.42 dBi|

This module is certified with the following integrated antenna.

Type: Metal antenna Internal Antenna.
Max. peak Antenna gain.

Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.
Label and compliance information

End Product Labeling
The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following

Contains FCC ID: BEJLGSBWAC03
Contains IC: 2703H-LGSBWAC03

Information on test modes and additional testing requirements OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, the additional transmitter in the host, etc. Additional testing, Part 15 Subpart B disclaimer. The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.

ISED
RSS-GEN, Sec. 7.1.3 license-exempt radio apparatus This device complies with Industry Canada licence-exempt RSS standard. Operation is subject to the following two conditions this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device.