Handscape Muja Mini Smart Touchpad User Manual

**Handscape Muja Mini Smart Touchpad User Manual

**

Specifications

• Bluetooth Version: 4.2
• Dimension: 87.3626.238.81mm
• Supported Operating System: iOS / Android
• battery capacity: 90m Ah
• Charging Time: 2h
• Working Current: working circuit <8mAh
• Charging voltage: +5V/50mA
• Use Time pre Charge: 20 h
• Temperature Range: 0°F – 122 °F
• Weight: 24.5 g

This product should not be disposed of casually when it is discarded.
It needs to be collected separately and treated specially.

Product Information

1. Touch area
2. Indicator light
3. Power button
4. Button
5. charging port

Packing List: MUJA Mini , Charging Cable, Product Manual (Warranty card ) ,Activator (Android)

Steps For Usage

Step 1
First put the phone into the top of the MUJA Mini

Step 2
Pull out the bottom rod to grip the screen

Please followed steps above to avoid damage to the screen saver.

Failure to install properly in order may cause damage to the phone film

Download the M+ assistant App.

iOS users can download and install “M+ Assistant” from Apple’s official “App Store”
Android users need to open the website “www.handscape.com“go to the download page and download the “M+ Assistant”.You can also scan the QR code below to downlaod the Android version M+ assistant.

Or scan the QR code below and follow the “szHandScape” public We chat number and see the detailed steps.

Operation and indicator description

LED smart working indicator status

Power on| Slide up the”ON/Off” button| The blue indicator flashes slowly and
enters the Bluetooth searching state.
---|---|---
Connection| Connected| The blue indicator long light for 2s and then off
Not connected| The blue indicator flashes slowly.
Power off| Slide down the”ON/Off’ button| The blue indicator is off
Electricity| When the battery is below 20%| The blue indicator flashes twice, repeat the cycle after 0.5s interval
When charging| The blue indicator flashes quickly
When charged fully| The blue indicator light is always on

Note:

• The “On”button and the “Off” button are the same button.
• When the blue indicator flashes slowly for one minute, and Bluetooth is not connected it will automatically shut down

Question and Answers

1. The blue light flashes and then goes out, but the M+ assistant shows that Bluetooth is not connected?

   • Turn on the phone Bluetooth and check if the device is connected. If not connected, check if it is connected to other mobile phones; if connected, ignore the Bluetooth device (cancel Bluetooth pairing), manually switch Bluetooth once, and then search for connected devices again.
   • Close the app from the background and reopen the app.
   • Restart the phone, search for Bluetooth in the app, connect the device

2. How to switch Android/i0S mode to use in Android/iOS phone?
   When MUJA Mini connects to Android M+ assistant, it will automatically switch to Android mode. When connected to Apple M+ assistant, it will automatically switch to Apple mode. Players can reconnect MUJA Mini after switching modes automatically.

3. Why I cannot upgrade the firmware?

   • Check if the network signal is stable
   • Check if MUJA Mini and mobile phone Bluetooth are disconnected
   • May be MUJA Mini is low on battery. Reconnect the M+ assistant for firmware upgrade .Connecting MUJA mini with power cable.

If still has questions, please scan the QR code to follow the official WeChat Account or send us email: contact@szhandscape.com

Warranty Card

Release date _____
Inspector _____

For the sake of your rights and interests, please fill in it carefully and make good safekeeping, which is as the voucher for repair.

Dealer’s Information:
Product Type _____
Dealer’ Name _____
Contact Tel. _____
Sales Date _____
User’s Information :
User’s Name _____
Contact Tel. _____
Postal Address: _____
email G QO _____

HandScape & Rock product after-sale service commitment table of comparison

Components and spare ports beyond tne scope of warranty

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Contact

ShenZhen HandScape technology Co.,Ltd.
512 Huashenghui Commercial Building,
Xixiang Street, Baoan District, Shenzhen
Website: www.handscape.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>