Shenzhen Smart Device Technology SV-1082X Smart Pass Management Module User Manual
- June 5, 2024
- Shenzhen Smart Device Technology
Table of Contents
Shenzhen Smart Device Technology SV-1082X Smart Pass Management Module
It can be used with access gates and attendance for communities, office buildings, schools, hotels, scenic spots, transportation hubs and other public service places.
Parameters
Installation Notes
- Module structure description
- Port description
- Installation method (installed with SV-1081D)
- According to the requirements of the installation site, open a 35mm diameter hole (as shown in the figure below) in the space position of the gate (usually the middle or front side).
- Unscrew the nut at the botom of the gate head post, thread the cable out of the nut, and remove the nut.
- Under the gate, insert the cable and cable interface into the gasket and nut in turn, tighten the nut, connect the pOwer supply, and the screen will start.
FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and tound to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Non-modification Statement:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for
uncontrolled environments. This equipment should be installed and operated
with a minimum distance 20cm between the radiator and your body.
Care and Maintenance
- During the installation and use of the product, all electrical safety regulations must be strictly observed.
- Please use the power adapter provided by the regular manufacturer. For specific requirements of the power adapter, see the product parameter table.
- When installing on the gate, please make sure that the product is installed firmly.
- If the product does not work properly, please contact the after-sales service personnel. Do not disassemble or modify the product in any way. (The company does not assume any responsibility for problems caused by unauthorized modification or repair.
- Do not immerse the product in water. When the product is installed Outdoors, try to use It with the rain cover provided by Our company.
- Please understand that you are responsible for properly configuring all passwords and other related product security settings, and keeping your username and password properly.
- If the equipment does not work properly, please do not disassemble it for repair, otherwise, it will affect the equipment warranty.
- Avoid extreme or extreme environments such as extremely high temperatures (or low temperatures), high humidity, vibration, radiation, and chemical corrosion during installation and use.
Warranty Card
Dear customer, thank you for purchasing the Face Recognition Pass Management
Module. In order to better serve you, please read, fill in and properly keep
the warranty card after purchasing the product. 
Warranty Description:
- This warranty card is required to be properly kept by the user of repair.
- This product is guaranteed for one year from the date of purchase.
- Warranty Equipment During the warranty period, under normal use and maintenance conditions, the machine itself malfunctions. Upon inspection, the company will provide free repair and parts replacement.
- During the warranty period, if the following events occur, the company has the right to refuse service or charge materials and maintenance service fees as appropriate.
- This warranty card and valid proof of purchase cannot be provided.
- Product failure and damage caused by improper user use.
- Damage due to abnormal external forces.
- It is not our maintenance service, and the user dismantles it to cause damage.
- Failures and damage caused by natural disasters or other force majeure factors.
- Others were intentionally damaged.
- The company reserves the right to modify and interpret all content.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>