ROSSETTA RS-KLD10 Star Projector Night Light User Guide

ROSSETTA RS-KLD10 Star Projector Night Light

INTRODUCTION

Thank you for purchasing the Rossetta Galaxy Projector. This product is a unique indoor light projector that uses starlight and holographic technology to project thousands of moving pinpoints of light against a transforming ocean wave. Sleep under the stars, create a romantic starlit dinner, or take your home entertainment center to the next level. We hope you enjoy this incredibly unique lighting experience.
Each unit provides up to 35 x 35 ft of coverage. It has maximum electrical usage of less than 10 Watts and operates in temperatures between -4° F to 122° F (-20° C to 50° C).

BEFORE YOU BEGIN

Immediately upon receiving the light projector, carefully unpack and check the carton contents to ensure that all parts are present and in good condition. Notify the retailer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that the light projector must be returned, it is important that the light projector be returned in the original factory box. Please see packing list below for box contents.

PACKING LIST

1. Galaxy Projector
2. USB-C Power Cord
3. Remote Control
4. Adjustable Base
5. User Manual

Please note:
Included USB-C cable may vary from picture shown.

SETTING UP THE STAR PROJECTOR

Before operating your star projector, please read the “Before you Begin” section and 0Notice” section of this user’s guide.

1. Remove protective film sticker from light aperture.

2. Insert the USB power cord into a powered USB port or use the included wall adapter
   to connect to an available electrical outlet. It is best practice for users to connect the power adapter to the wall before connecting the device to the power adapter.

3. Place the Rossetta galaxy projector on a flat solid surface and aim toward desired ceiling/wall.

4. Press the power button. The ocean wave and stars will gradually illuminate and begin moving by default.

5. To adjust the illumination angle for walls, tilt the light forward onto the secondary
   support panel.

6. To turn off the light, cycle through the power button modes until the unit turns off completely. Remove the power plug from electrical outlet.

HOW TO USE

1. Indoor use, projecting in the sky direction.
2. How to use the light projector, as shown below.
3. Connect Bluetooth “RS-KLDl O” of the smartphone to play music.
4. Use correct method of the remote control to make sure the remote control is poinng at the infrared sensor that is the “Remote Receiving Area” on the host.

PRODUCT FEATURES

1. Manual Mode: Press device buttons or remote control to switch the functions. In manual mode, the device default automatically standby after 4 hours.
2. Bluetooth Mode: You can connect your phone Bluetooth to play music, also use Smart Night Light App to control the device switch on/off, ocean wave or starlight mode switch, single projecting the ocean wave light, starlight, music playing or combinations, select different scene modes, custom the body clock functions.
3. Timer Mode: Use remote control or App to custom the standby time.
4. Voice Control: Press “Mic” button on the remote control or App interface to activate voice control function. The projection light will fast flash according to the external sounds or music rhythm.
5. White Noise Mode: Press device buttons, remote control or App to play the built-in white noise sounds.

MANUAL MODE

1. Short press play previous song; Long press reduce volume.
2. Short press play next song; Long press increase volume.
3. Short press control the music play/pause.
4. Bluetooth and white noise modes switching.
5. DC Input: 5V/2A.
6. Power ON/OFF mode switching.

REMOTE CONTROL FUNCTION DESCRIPTION

Instruction:
When music starry projector connects power; LED blue light keeps on and in moving status; star light in breathing mode, it can default automatically standby after 4 hours.(timing without daily circle)

• Power Switch: The default mode is ocean wave light moving and starlight in breathing status (ocean wave light default moving in normal speed)
• Star Light Switch: Control the star light switch on/off
• Built-in White Noise: Ocean Wave — White Noise — Summer Night — Thunder
• Built-in White Noise: Brook — Baby Lullaby 01 — Baby Lullaby 02 — Baby Lullaby 03
• Press “R”, red light on; press again, red light off (at basic of light on at first time)
• Press ‘G”, green light on; press again, green light off (at basic of light on at first time)
• Press ‘B”, blue light on; press again, blue light off (at basic of light on at first time)
• Press “W”, white light on; press again, white light off (at basic of light on at first time) ® Pause @ Volume Up @ Volume Down @Previous Song @ Next Song
• Control the ocean wave light switch on/off
• Voice Control Switch: Lights will fast flash following the external sound or music rhythm
• Control the ocean wave light brightness adjustment
• Control the ocean wave light moving speed up
• Control the ocean wave light moving speed down
• FADE 1: Ocean wave light moves circularly in R-G-B-W single color mode
• FADE 2: Ocean wave light moves circularly in RB-RG-RW-BG-BW-GW double-color mode
• Control the starlight achieve either stay on or enter into breathing mode
• Control Bluetooth and white noise mode switch
• 1 H Timer: Short press it, ocean wave light/starlight flash once time as prompting for set 1 H timer successfully
• 2H Timer: Short press it, ocean wave light/starlight flash 2 times as prompting for set 2H timer successfully
• Timer Off: Short press it, ocean wave light/starlight flash 3 times as prompting for set

Notice:
This product comes with 4 hours automatic standby function that works for 4 hours then left in standby mode.

BLUETOOTH MODE

1. Bluetooth Setting
   • Please turn on your phone Bluetooth, or the product won’t be connected
   • Download “Smart Night Light” App by scanning the QR code directly
   • Search “Smart Night Light” App through Google Play(for Android) or APP Store (for Apple-iOS) and download it
2. Register and log in to the App
   • Turn on “Smart Night Light” App
   • Log in your account and password. Please register a new account on first use
3. Configuration
   Connect the music starry projector with power supply, enter the main interface(fig.1), click “Add Device” or “O” button to enter “Product Selection” interface(fig.2).
   Choose the product and enter “Find the Device”interface(fig.3) (Please allow the app to access Bluetooth and previously turn on the Bluetooth. Note: For Android, please also allow to access the location and turn on the location). Power on the device and keep close to the app to identify the device, see the pop-up shown(fig.4), then adding the found device.

APP FUNCTIONS

Click on the “Music Star Light” icon to enter the main interface, touch the Power Switch”®” to turn on/off the music starlight. Custom the product name via the icon”!”;! “at the top right-hand corner, turn on the voice-activated mode via Mic “0” button
Click “Timer” icon “@”to set a timer of the device auto turn on/off: Make the device automatically turn on/off in a custom time. (Note: The device cannot set the auto standby time exceed 4 hours)
Click countdown icon to enter the countdown interface. Click “Start” to perform the countdown function and click “Over” to cancel it.

Four Main Interfaces as follows:

1. Ocean Wave Light Interface;
2. Star Light Interface;
3. Music Play Interface;
4. Scenario Interface

Ocean Wave Light Interface:

1. turn on/off ocean wave light;
2. turn on/off white light/color light;
3. turn on/off ocean wave light breathing mode; 4). adjust the color lights;
4. choose 6 mixed-colors ocean wave effects; 6). adjust white light brightness;
5. adjust color light brightness;
6. adjust color light saturation;
7. adjust the ocean wave moving speed.

Star Light Interface Features as follows:

1. turn on/off starlight;
2. turn on/off starlight breathing mode;
3. adjust starlight brightness

Music Play Interface Features as follows:

1. play/pause the music, switch the previous/the next song;
2. adjust the volume;
3. select the sound effects, the light will dance to the music, and you can adjust the rhythm sensitivity;
4. White Noise/Music Speaker Mode Switch;
5. White Noise Selection Pop-up;
6. Rhythm Sensitivity Adjustment. 

Scenario Interface Features as follows:

1. turn on/off the light;
2. color light/white light combination, adjust brightness, 3 color-changing modes:
   • Static mode; b. Flash mode; c. Breathe mode. Custom the color changed speed in static, flash and breathe modes;
3. Star light on/off, adjust starlight brightness, starlight breathe mode on/off;
4. choose your custom scenario and save your rename, convenient to restart your favorite scenario effects next time.
   Preset Scenario Mode Selection: Click the preset scenario icon, select 48 kinds of scenario mode effects in the system.

TROUBLESHOOTING FOR NETWORK CONFIGURATION· FAIL TO CONNECT TO PHONE

BLUETOOTH

1. Please check your phone Bluetooth access permission and turn on the Bluetooth (For Android, please also allow to access the location and turn on the location).
2. Please check the music starry projector power on and keep close to the connection range (0~10m).
3. Please check your phone Bluetooth connect to the correct model “RS-KLDl O”.
4. Please check your phone network works normally.

DEFAULT SETTINGS

Once the star projector is plugged in, it will enter the default mode where all effects are on. Use the remote control to change the effect setings and brightness. This light has a built-in timer that is designed to be automatically on standby after 4 hours of operation.

INSTALLATION TIPS

• Do not connect the light to a dimmer pack, as a dimmer accessory may damage the star component.
• The darker the display area, the brighter your projection will appear.

PRODUCT SPECIFICATIONS

Designed in the USA
By Rossetta LLC
Broward
Pompano Beach, FL 33068 Made in China

ROSSETTA LIMITED WARRANTY

This product carries a 1-year limited warranty against defects in workmanship and materials. Rossetta LLC agrees to replace the defective product free of charge within the stated warranty period when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.

CAUTION
This is not a toy. Young children under 3 yrs must be supervised while using this device at all times. This unit is not waterproof. Use and store indoors or in a dry place.

CLEANING INSTRUCTIONS
Surface clean only with a soft, dry cloth. Unplug unit before cleaning.

DISPOSAL
At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

FCC Warning

Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>