arcadyan WN8711BTAAC-YA Wireless LAN Network Module User Manual

Wireless LAN Network Module
User Manual

Model: WN8711BTAAC-YA

SPECIFICATION

1-1  Basic Specification

Detail Specification

2-1. Product Specification

2-1-1. Connector Specification

CON1 – 32×2 pin connector

FCC Statement
Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
• Consult the dealer or an experienced radio/TV technician for

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This device is restricted to indoor use.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
This module is intended for OEM integrators only. The OEM integrator is responsible for compliance to all the rules that apply to the product into which this certified RF module is integrated.
Additional testing and certification may be necessary when multiple modules are used.OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install the module
The module is limited to installation in mobile or fixed applications, according to Part 2.1091(b).

USERS MANUAL OF THE END PRODUCT:

In the user’s manual of the end product, the end-user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end-user has to be informed that the FCC radio- frequency exposure guidelines for an uncontrolled environment can be satisfied.
The end-user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
If the labeling area is small than the palm of the hand, then an additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following ” Contains TX FCC ID: RAXWN8711 “.
If the labeling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation

Ant.| Brand| Model Name| Antenna Type| Connector| Gain (dB)
---|---|---|---|---|---
2.4GHz| 5GHz
1| ACON| AIMEE-10000| Dipole Antenna| Reversed-SMA| 3.24| 4.54
Cable| Brand| Model Name| Cable Length (mm)| Cable Loss (dB)| True Gain (dBi)
---|---|---|---|---|---
2.4GHz / BT| 5GHz| 2.4GHz / BT| 5GHz
1| ACON| AEC8P-1000001 (Black)| 30| 0.08| 0.12| 3.16| 4.42
2| ACON| AEC8P-1000003 (Black)| 50| 0.13| 0.19| 3.11| 4.35
3| ACON| AEC8P-1000005 (Black)| 70| 0.19| 0.27| 3.05| 4.27
4| ACON| AEC8P-1000007 (Black)| 90| 0.24| 0.35| 3.00| 4.19
5| ACON| AEC8P-1000009 (Black)| 120| 0.32| 0.46| 2.92| 4.08
6| ACON| AEC8P-1000011 (Black)| 160| 0.43| 0.62| 2.81| 3.92
7| ACON| AEC8P-1000013 (Black)| 200| 0.54| 0.77| 2.70| 3.77
8| ACON| AEC8P-1000015 (Black)| 240| 0.64| 0.93| 2.60| 3.61
9| ACON| AEC8P-1000017 (Black)| 280| 0.75| 1.08| 2.49| 3.46
10| ACON| AEC8P-1000019 (Black)| 320| 0.86| 1.24| 2.38| 3.30
11| ACON| AEC8P-1000021 (Black)| 360| 0.96| 1.39| 2.28| 3.15
12| ACON| AEC8P-1000023 (Black)| 400| 1.07| 1.54| 2.17| 3.00
13| ACON| AEC8P-1000025 (Black)| 450| 1.21| 1.74| 2.03| 2.80
14| ACON| AEC8P-1000027 (Black)| 500| 1.34| 1.93| 1.90| 2.61

IC Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit.
The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices
For indoor use only

IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This radio transmitter (IC: 4711A-WN8711) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device

IMPORTANT NOTE:
This module is intended for OEM integrators. The OEM integrator is responsible for compliance to all the rules that apply to the product into which this certified RF module is integrated.
Additional testing and certification may be necessary when multiple modules are used.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

In the user’s manual of the end product, the end-user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end-user has to be informed that the IC radio- frequency exposure guidelines for an uncontrolled environment can be satisfied.
The end-user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following ” Contains IC: 4711A-WN8711 “.
The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online.

Ant.| Brand| Model Name| Antenna Type| Connector| Gain (dBi)
---|---|---|---|---|---
2.4GHz| 5GHz
1| ACON| AIMEE-10000| Dipole Antenna| Reversed-SMA| 3.24| 4.54
Cable| Brand| Model Name| Cable Length (mm)| Cable Loss (dB)| True Gain (dBi)
---|---|---|---|---|---
2.4GHz / BT| 5GHz| 2.4GHz / BT| 5GHz
1| ACON| AEC8P-1000001 (Black)| 30| 0.08| 0.12| 3.16| 4.42
2| ACON| AEC8P-1000003 (Black)| 50| 0.13| 0.19| 3.11| 4.35
3| ACON| AEC8P-1000005 (Black)| 70| 0.19| 0.27| 3.05| 4.27
4| ACON| AEC8P-1000007 (Black)| 90| 0.24| 0.35| 3.00| 4.19
5| ACON| AEC8P-1000009 (Black)| 120| 0.32| 0.46| 2.92| 4.08
6| ACON| AEC8P-1000011 (Black)| 160| 0.43| 0.62| 2.81| 3.92
7| ACON| AEC8P-1000013 (Black)| 200| 0.54| 0.77| 2.70| 3.77
8| ACON| AEC8P-1000015 (Black)| 240| 0.64| 0.93| 2.60| 3.61
9| ACON| AEC8P-1000017 (Black)| 280| 0.75| 1.08| 2.49| 3.46
10| ACON| AEC8P-1000019 (Black)| 320| 0.86| 1.24| 2.38| 3.30
11| ACON| AEC8P-1000021 (Black)| 360| 0.96| 1.39| 2.28| 3.15
12| ACON| AEC8P-1000023 (Black)| 400| 1.07| 1.54| 2.17| 3.00
13| ACON| AEC8P-1000025 (Black)| 450| 1.21| 1.74| 2.03| 2.80
14| ACON| AEC8P-1000027 (Black)| 500| 1.34| 1.93| 1.90| 2.61

Select Statement
5GHz band (W52, W53): Indoor use only

CE Statement
For MPE Statement – Mobile device
This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
All operational modes:
2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), Bluetooth(BR/EDR, LE)
5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80)
The frequency and the maximum transmitted power in the EU are listed below :
2412-2472MHz: 19.99 dBm
2402-2480MHz (BR/EDR): 7.27 dBm
2402-2480MHz (LE): 5.33 dBm
5180-5240MHz: 22.77 dBm
5260-5320MHz: 22.84 dBm
5500-5700MHz: 23.88 dBm
5745-5825 MHz: 13.96 dBm

| AT| BE| BG| HR| CY| CZ| DK
---|---|---|---|---|---|---|---
EE| FI| FR| DE| EL| HU| IE
IT| LV| LT| LU| MT| NL| PL
PT| RO| SK| SI| ES| SE|

LLAN: restricted to indoor use only when operating in the 5150-5350 MHz band .

Documents / Resources

| arcadyan WN8711BTAAC-YA Wireless LAN Network Module [pdf] User Manual
WN8711, RAXWN8711, WN8711BTAAC-YA, Wireless LAN Network Module, WN8711BTAAC-YA Wireless LAN Network Module
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>