AUDIO STUDIO SD-01 David Ⅰ Speaker Instruction Manual

AUDIO STUDIO SD-01 David Ⅰ Speaker

FUNCTION INSTRUCTION

OPERATING INSTRUCTION

Automatic Connection

1. After startup, the speaker will automatically enter pairing mode and automatically reconnect to the device last connected. Once successfully connected, a prompt tone will sOund.
2. While connected, when the device is away from the speaker, it will disconnect. If the device returns  to a connectable distance within 10 min, thespeaker will automatically reconnect to the device
   In the event of no connection within 10 min, the speaker will enter sleep mode.

TWS Pairing

After both speakers have been turned on, press and hold the power button of one speaker for 2s to enter TWS pairing mode. The other speaker will automatically enter pairing mode to complete TWS pairing. After pairing, the master enters into pairing mode (unless it has been connected with a phone). Now, connect the master to the phone to play on both speakers at the same time

Shutdown

1. Press and hold the power button for 4s to enter sleep mode.
2. The spea ker will enter sleep mode it no activities, such as music playing or Bluetooth connection, is executed for 10 min.

Re-Pair

1. After a successful connection, disconnect the Bluetooth connection from the phone so that the speaker enters into pairing mode again. With other phones, search for the speaker to pair and connect again.
2. Alternatively, press the power button twice to enter pairing mode. Then, search for the speakerwith other phones to pair and connect again.

AUX Mode

1. After the speaker has been turned on, connect the audio output cable of the intelligent device to the 3.5mm stereo input intertace of the speaker to play music
2. After AUX is connected, priority will be given to the connected AUX channel. The AUX function will also be prioritized if the AUX is connected before startup. The speaker will automatically convert to Bluetooth mode after AUX is disconnected.

Bluetooth Connection

After startup, the speaker automaticaly enters into pairing mode and will Sound a pairing prompt tone followed by a quick flash of blue light. Search F Speaker David” on the device, the name of the speaker, and execute paired connection. Once the  device is successfully connected, a prompt tone willsound and the blue light flashes once every 4s.

Status of the Speaker’s LED Indicator Light

Function/Status

• Pairing mode/Quick flash
• Successfully Paired/Slow flash (once every 4s)
• Paired Status/Flash (once every 1s)
• AUX Mode/Breathing Light
• Sleep/Off

SPECIFICATION

• Dimensions: 800-600:408mm
• Weight:15KG
• Packing list:Speaker, User Manual, power adapter
• Power Input:20V/5A
• Speaker output:55W+25W2
• Distortion:< 10%
• SNR:>90dB
• Noise floor/ <1mV
• Frequeny response/33Hz-18KHz
• Drive unit/6.5-inch bass, 3-inch-2 alto/treble
• Distance/>10m
• Bluetooth version/V5.3
• Frequency range/2400-2483.5MHz
• Bluetooth protocol/A2DP (SBC protocol), AVRCP

FCC STATEMENT

This device complies with Part 15 of the FOC Rules. Operation is subject to the following two conditions:

1. This device may not cause hamful interference, and
2. This devioe must acept any interference received, indluding interference that may cause undesired operation.

Waming: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interferenoe in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partiaular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
www.if-audio.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>