AW Auto World ELECTRIC SLOT CAR RACE SET User Manual

AW Auto World ELECTRIC SLOT CAR RACE SET

IMPORTANT: Save all packing materials!

After unpacking your race set, use the list below to ensure all the parts are present. If something appears to be missing, check again through all the packing materials and cartons to make sure no parts were missed when unpacking.

WARNING: This race set contains parts with sharp edges. Unpacking, assembly, and use should take place only under the direct supervision of an adult.

PARTS LIST

SAFE SET-UP REMINDERS

• This race set is not intended for children under 3 years of age.
• If this race set is being operated in the presence of children under 8 years old, adult supervision is advised.
• Select a hard, flat, and clean surface to assemble your track layout.
• Select a location close to a convenient power] receptacle and ensure the adjustable voltage power pack cable is not stretched too tight. This may cause it to malfunction or create a tripping hazard.
• Assemble track layout before connecting speed controllers or adjustable voltage power pack.
• Plug in speed controllers before connecting the adjustable voltage power pack to the terminal track. Plug adjustable voltage power pack into wall receptacle LAST.
• Only use included AUTO WORLD adjustable voltage power pack with this race set.
• Unplug the adjustable voltage power pack when assembling, disassembling, or CLEANING Track.
• Always unplug the adjustable voltage power pack when the race set is not in use.
• When connecting or disconnecting the speed controllers or adjustable voltage power pack, always grip the connector and NOT the cable.
• Inspect adjustable voltage power pack cable, connector and transformer for damage BEFORE EACH USE, and regularly thereafter. Check for the following problems:
  • exposed or frayed cable wires
  • nicks or cuts in cable insulation

If any damage is discovered, DO NOT use the adjustable voltage power pack or race set until the problem has been corrected.

• The adjustable voltage power pack is NOT a toy.
• DO NOT attempt to open or modify the adjustable voltage power pack – No consumer serviceable parts inside.
• Disconnect the adjustable voltage power pack before cleaning it.

TRACK LAYOUT MAP

• This race set track layout requires an area of 102″ x 50″.

PLEASE READ “SAFE SET-UP REMINDERS” ON THE BACK OF THIS MAP BEFORE ASSEMBLING THE RACE SET!

• Extra guard rails are included in the set as replacements. They may also be added to other track pieces as desired.
• Following this map, loosely lay out all track pieces first before making connections. Attach guard rails to all curved track (outside) sections before assembly.

NOTE: Charging Cord plugs into the back of each controller

This set features the NEW Auto World Adjustable Voltage Power Pack unit

• The adjustable power pack allows you to increase or decrease the power supply to your race set.
• Simply turn the dial on the unit as marked (from 9 to 24 volts), to make adjustments.
• Decreasing the power supply will slow down the rate of speed of your slot cars, this may be more desirable for beginning racers.
• Increasing the power supply will allow for higher rates of speed making it more appropriate for advanced racers.
• This new speed variable option makes this set the perfect set for a wider range of slot car racers.

Pairing the Wireless Controllers to the Terminal Track

1. PLEASE READ THE DIRECTIONS BEFORE BEGINNING PAIRING
2. Make sure the power pack is plugged into the terminal track, and the arrow on the connector is pointing to the right. For adjustable voltage power packs, make sure the power pack is turned on (make sure the power pack is plugged into the outlet).
3. Turn on the wireless controller.
4. Press the pairing button on the controller for 2 seconds, or until the LED flashes. Release the button once the light flashes.
5. While the LED light on the controller is flashing, quickly press the pairing button on the controller again. The LED will change color every time the button is pressed. Each color represents a different lane.
6. Choose the lane you’d like to control by selecting the correlating color.
7. Press the pairing button on the terminal track.
8. You should now see the LED of the correlating lane on the terminal track is lit in the same color that shows on your controller. Your controller will stop flashing, and be continuously lit in the color of the chosen lane. Follow these steps again to change which lane each controller commands.

Charging Wireless Controllers

• Step 1: Attach each of the 4 controllers to the 4 into-1 charging cable.
• Step 2:  Plug the USB cable into any applicable USB power source (Wall plug power adapter, laptop or computer).

PARTS KEY

A1| 15″ 4-Lane Wireless Terminal Track
A2| 15″ 4-Lane Terminal Connection Track
B| 5″ Straight Track
C| 6″ Straight Track
D| 9″ Straight Track
E| 9″ Mechanical Lap Counter
F| 15″ Straight Track
G| 6″ Radius Curve 1/8 Circle Track
H| 6″ Radius Curve 1/4 Circle Track
I| 9″ Radius Curve 1/8 Circle Track
J| 9″ Radius Curve 1/4 Circle Track
K| 12″ Radius Curve 1/8 Circle Track
L| 15″ Radius Curve 1/8 Circle Track
X| 4-1 Charging Cable
Y| 4 Wireless Controllers
Z| Adjustable Voltage Power Pack

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>