HYDX D800 Digital DMR Two Way Radio User Manual

HYDX D800 Digital DMR Two Way Radio

INTRODUCTION

Thank you for buying a handheld walkie-talkie. We believe this simple, stable, beautiful and widely used in all industries and areas of professional wireless communication equipment will give you a great surprise. This product is for professional commercial or amateur frequencies, it is necessary to apply for permission to the wireless administrator organization of the provinces and autonomous regions in their local country. Please read this manual carefully in order to know how to properly operate the radio before use.

Unpacking and Checking Equipment

Welcome to use hand-held radio,before using we suggest you:Please check the packing box of this product and see if there are signs of damage.Please open the packing box carefully. We recommend that you identify the items listed in the following packing list. if you find that our product and its accessories i handling are lost or damaged during the shipment. Please immediately contacdealers.

Parts List

Using the Battery

The battery is not completely charged at the factory, please charge it before using. To extend the battery lifetime, please power off the batteries when you don’t use two way radio, and save battery in a cool (temperature less than 25°C )and dry place.

Precautions of Charging Equipment

•  Do not expose the charger to rain or snow.
•  Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way.
• Never alter the AC cord or plug provider with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock.
•  To avoid damaging the power cord or socket, pull the plug out of the socket with a hand plug. Do not pull the plug out by pulling the power cord.
•  To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle.
• Use of an attachment not recommended or sold may result in a risk of fire, electric shock, or personal injury.
•  Make sure the cord is located so it will not be stepped on, tripped over, or subjected to damage or stress.
•  An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and/or electric shock. If an extension cord must be used, make sure that:
  •  Extension line cord use the same pins.
  •  Use 18AWG wires less than 30 meters in length and use 16 AWG wires within 45 meters.
•  Do not replace charger’s power cord. If the power cord damages, you must stop using charger immediately. Charging the Battery Please use the battery charger designated to charge battery. After purchase or extended storage (more than two months), the first time to charge battery cannot make battery reach its normal operating capacity. After repeating charge /discharge it two or three times, the operating capacity will increase to its normal capacity. Please Charge the Radio According to Operation Steps as Follows:
  •  Inset power adapter into power supply socket.
  •  Inset output terminal of power adapter into DC Jack behind the charging kit,now the charging orange indicator lights about 2 seconds then goes out.
  •  Inset the battery or radio equipped with battery into the charging kit.
  • Confirm the battery and charger kit terminal contact reliably, when charging indicator light turns into red and charging starts.
  • After completion of charge (charging time is about 4 hours),light turns to be green.

Indicators Display As Following

goes out

No battery (Temperature end judges)| All go out
Charge Normally| Red light is on
The battery is fully charged| Green light is on
Fault(over temperature, battery short

circuit or over discharge state)

| Red light flashes

Preparation

• Installing/Removing the Battery
  • Insert the battery pack into the corresponding slots on the back or radio and push it Then press the upper end of the battery until you hear a “click”.To remove the battery pack, make sure the radio off, and then unlatch the buckle, the  battery from emerge from the radio, and then remove the battery.
• Installing/Removing the Antenna
  • Align the threaded of the antenna with the radio’s antenna connector. Tum the antenna clockwise to fasten it. To remove the antenna, please tum the antennacounter-clockwise until you can remove it
• Installing/Removing the Belt Clip
  • If necessary , the randomly configured belt clip can be inserted into the slot on theback of the battery pack for easy canying.  To remove the belt clip, simply press the buckle out and push it up.
• Installing Speaker/Microphone
  • Lift the headphone cover and insert the speaker/microphone headset directly into the speaker/microphone Jack.

Getting Familiar

Basic Use of Keyboard:

SK1:Defined programming Key (can be set long/short press function)
SK2:Defined programming Key (can be set long/short press function)

Safety

Product safety and RF Exposure for hand-held two-way radio before using this two-way radio,please read carefully the attach manual instruction i the random incidental for the safe use of the product and radio-frequency manual.

Overview

Switch On

Clockwise to turn on the radio volume knob, there will be a “KADA” SOund, message SOund and the screen will show up “Welcome”, while the LED indicator lights up and becomes Green color if the battery ID full charged. Note: if the volume function i forbidden, there wil not any sound when power on. Here, need to power off the radio and anticlockwise with knob until a “KADA” sound. Boot custom character content of  PC can be set.

Adjust Volume
Clockwise the volume knob to higher the volume or anticlockwise to lower.

Launch Calls
Single Cal

• This radio supports a confirm single call, if the check is confirmed, it is necessary to detect the presence of the target radio before calling the other party.
• When the default communication address of the digital channel is set to single call ID, press PTT key to initiate a single call for the current contact.
• On the contact menu, select the single caller to press the PTT key to call th selected single caller.
• When the programming key is set as a one touch to access digital single call contact, press the corresponding button and then press the PTT key can launch single cal.
•  Select the single call contact in the callerfreceived/unconnected number, and pressPTT key can launch a single call.

Group Call

•  When the default communication address of the digital channel is set as group call, can press the PTT key to launch group calling.
• On contact’s menu, select group ID then press PTT key to launch a group calling.
• ln the dialed records/received/unanswered number select group call, press PTT keycan launch the group call.
• When the programming key is set as a one touch to access digital single call contact, press the corresponding button and then press the PTT key can launch single call.

All Call

• When the default communication address of the digital channel is set as all call ID,can press PTT key to launch all calls.
• On the contact menu, select all call ID then press PTT key to launch all call.
• ln the dialed records/received/unanswered number select all call ID, then press PTT key can launch all call.
•  The receiver of all call can not answer all call.
• Note: If the call prompt setting is enabled, press the PTT key for transmitting, the transmitter and receiver will hear a fixed hint tone.

Launch and Receive Calls

In the digital mode, received a single call and the interface display a single call, in the single call pending time, press PTT key can respond the current single call.Beyond the pending time is record as an unanswered call. Received the group call ,the interface displays group call. In the group call pending time , press PTT key can respond the current group call, beyond the pending time is record as an unanswered call. Received the all call and the interface display all call,I, the all call does not have han up time, so can’t respond the all call.
Note

• lf set the channel free instructions, when transmitter press PTT key, receiver will hear a short hint tone.
• when the name display in the digital contact is set to closed, the calling in/out of the digital channel will not show the name, but only show the ID number, when the setting is on, digital channel calling in/out display name

Menu Operation

Contacts
Contacts can be viewed contact list (up to 1024 digital contacts can be added

• Group Call Type
  • When the selected the directory member type as group call, group caller can view group call ID or sent message.
•  Single Call Type
  • When the selected contact member type as single call, to the single caller contact can view contacts, send call prompt, the detection, remote monitoring, activation or  remote killing operation

Call prompt: send a call prompt to assigned single call contact, requesting the other reply when communicating.The interface will display call prompt and prompting bell when the other receive the call prompt ( there are 1 O ring tones to choose). If the other party can not receive, it will prompt the cal prompt failure. Radio detection: radio detection allows user to determine whether the radio is in a state of activity in the system without any instructions to the radio user. If received the respond, the successful radio interface shows that the radio detection is successful. If the respond is not received in a certain time, there is a failure prompt and the interface shows radio detection failed. Remote monitor: send the remote monitor request, if received the remote monitor confirmation, it has successfully entered the reception interface display. If not confirmation is received in a certain time, prompt the failure hint and the interface displays the remote monitor failed. Only when the device’s signaling system “remote monitor decode” is checked,can be allowed to monitored voice activities. Radio activated: This function can activated the dead device and make the target radio resume its normal working statue. Radio kill: Sent radio kill command,if received the respond,the radio interface shows kill successfully and has a successful hint .If the respond is not receive in a certain time.the radio interface shows kill fail and has a failure hint. When the signaling system receiving the radio configuration of device’s kill decode is checked, can receive the radio’s kill command. After being killed, the device disables all interfaces and only process the received telemetry command.

All Call Type

When selected contact type as all call, can view all call ID: 16777215. Note: This radio allowed to add group call type’s and single call type’s contact.After input number (1~16777214),the maximum can input sixteen characters.Name input is completed,press the selected tone then press confirmation to save.After successful preservation on the interface notice:save succeed.New contact can be found in the contact list.

Function Settings

Radio Setting

This function provides some parts of radio’s basic setting for user. Infra- acoustic Frequency(Only support analog channel ): The radio analog channe supports the function to ensure the quality of the call ,when channels active ATR function,it must be have the subsonic function(this function can be set in the programmable software). Voice output is allowed when the received subsonic is transmitting.Analog subsonic can be set ,(press P1 key to switch digital subsonic, analog subsonic and dose}.Selected a subsonic value from the exiting list to encode or decode, (the specific subsonic value is referred to the CTCSS frequency table and CDCSS digital code table)

• Decode:The radio of receiver will decode the sub-tone sent by the transmitter. The subsonic set up here matches the subsonic from the sender can open the loudspeaker and output the voice.
• Code:Before sending the voice, the transmitter terminal sub-codes the subsonic.which is added to the voioe and encode through the carrier. The receiver opens the speaker and outputs the voice when if receives the matching of the sub-tone set here. Note: Analog channel support setting non-standard analog subsonic function (range 60Hz~259.9Hz} and non-standard digital subsonic (range 001 ~ 777), and the coding and decoding of the programmable software also can manually input non-standard subsonic values.

CTCSS(Hz)

67.0| 69.3| 71.9| 74A| n.o| 79.7
82.5| 85.4| 88.5| 91.5| 94.8| 97.4
100.0| 103.5| 107.2| 110.9| 114.8| 118.8
123.0| 127.5| 131.8| 136.5| 141.3| 146.2
151.4| 156.7| 159.8| 162.2| 165.5| 167.9
171.3| 173.8| 177.3| 179.9| 183.5| 186.2
189.9| 192.8| 196.6| 199.5| 203.5| 206.5
210.7| 218.1| 225.7| 229.1| 233.6| 241.8
250.3| 254.1|  |  |  |
Standard DCS Code

023| 025| 028| 031| 032| 036| 043| 047| 051| 053
054| 065| 071| 072| 073| 074| 114| 115| 116| 122
125| 131| 132| 134| 143| 145| 152| 155| 156| 162
165| 172| 174| 205| 212| 223| 225| 228| 243| 244
245| 246| 251| 252| 255| 261| 263| 265| 266| 271
274| 306| 311| 315| 325| 331| 332| 343| 346| 351
356| 364| 365| 371| 411| 412| 413| 423| 431| 432
445| 446| 452| 454| 455| 462| 464| 465| 466| 503
506| 516| 523| 526| 532| 546| 565| 606| 612| 624
627| 631| 632| 654| 662| 664| 703| 712| 723| 731
732| 734| 743| 754|  |  |  |  |  |

• Squelch: Filtering out the intensity is not enough to generate clear incoming signals to eliminate unwanted noise. The lower the noise level, the easier to receive the signals. And at the same time, it will affect the interface of the useless calling The higher the noise level, the more useless calls will be filleted. However, calls from remote locations will be filleted out. The default setting is users can set the suitable squelch level according to their needs.
• Transmitting Power: Allow users adjust the radio’s transmitting power high/low b menu. High power display: H, low power display: L.
• Talk Around: When the radio works in the repeater mode, but the transfer service inot available, the radio can open the talk around function to enter communicate. When open the talk around  function, the screen will display and enter the talk around mode, the radio use TX frequency to transmit, so the two radios can achieve communicate directly.
• Note:
•  If want to enable this function, the RX frequency and the TX frequency mus be different, and the channel must check the talk around function by programmable software.
•  If the programmable key set as repeater/talk around function, also can openthe talk around function.

Wide/Narrow Band(only support analog channel):

Allow users to set up the radiosonde/narrow band by menu. Select wide band the main interface is not displayed,and the N is displayed when selecting a narrow band. Busy Channel Lockout: Allow users to select a state of lockout by menu, select tum off, busy channel lockout can’t work. Select carrier, this channel does not allow transmission when with the carrier. Select subsonic/code, this channel is prohibit launching when the subsonic or code is matched.

Note: If the transmission prohibits fast key over overwrite check of programmable software overall setting, when the channel is busy, press the launch key twice within one second can launch again.
Time Out Timer: lime out timer function can prevent the current channel occupied too long by the signal user. For the much busier channel, can set much shorter TOT. If the continuous launching lime exceeds the set value, the radio has the “beep” warning sound, and automatically terminates the launch. TOT can set by programmable software, 15-495 seconds, default 60 seconds, step 15 seconds.

VOX: Sounds control let you don’t press PTT key when launching, when the function is opened, the launch operation can be launch directly through the voice. When the voice stops, the launch is automatically ended. It allows users to open the VOX control by menu, and the screen shows . The overall setting in programmable software can be set of 1-10 levels, or set tum on/off in the channel.

Digital Encryption(Only support digital channel) : Voice encryption function can ensure language communication safety. Allows users select turn on/off or through radio’s menu or by software select basic encryption function and se encryption key by radio menu. Open the radio’s encryption function, the voic encryption function is same and the encryption key is same can communicate. If your radio receive a different encryption key’s call, then you will hear confusion. Note: The voice encryption function only valid in digital mode

Power Save: Enable this function can make the free radio automatically enter the power save mode, power save mode can extend the battery’s life, but will causes the respond time delay. The waking time is 1 :4, after the radio enter the power sav mode. The main interface shows 1 :4 after opened the power save. Note: The power save is invalid when open the double capacities directly mode.

Prompt Tone: Allows users turn on/off prompt tone by menu. Including all tones, call licenses and keyboard setting, all tones control all hints, including the voice number if turn off all hints, the alarm sounds also can still played normal. Indicator Lights: Allows users tum on/off the LED indicator lights of the radio bymenu.if necessary, set turn off the LED indicator light, it will prohibit the launch andreception of scan and the LED lights are not bright. Users should be careful turn off the LED indicator light, this setting will not effect the screen and keypad backlight. Mode Selection: Allows users select serial number, name, frequency channel displa mode by menu, the main interface will displayed according to the selected mode. Language Selection: it can support three languages of Chinese/ Korean/English Note: Korean/English and Chinese/English do not support text message.

Radio Information
My Number: Allows users to query this radio’s ID number by menu, which can only b accessed not set(Only can modified the settings by programmable software) Facility information: Allows users to query radio’s facility information by menu, which including type information, serial number, CPS version, hardware version,firmwar version,DSP version and the programmable time(also can read through by programmable software).

Radio Configuration
RX Frequency: check the current channel RX frequency (it can be modified b programmable software). TX Frequency: check the current TX frequency (it can be modified by programming ables software)Channel Name: check the current channel name(it also can be modified byprogrammable software). Color Code (Only support digital channel): Users can modify the color code according their needs, there are 0-15 optional (it also can modified by programmable software).

Time Slot (Only support digital channel): Users can modify the time slot according to their needs, there have time slot 1, and time slot 2 options (it also can be modified by programmable software).

Zone The radio can support 2 zones at most, one zone can add 16 channels at most, 2 zones can support 32 channels at most. Through the menu zone options, you can enter the selected zone in the zone list, or set as a zone switchable function in the programmable keypad, and then enter the zone switchable(it should be set as two zones. then can make the zone switchable). Note : If program the SK1 as zone selection, short press SK1 to up select the zones, long press to quit the zone selection; short press SK2 to down select the zones,long press to quit the zone selection .

Scan Your radio can support 2 scanning lists at most and with a maximum of 32 members for per scan list, each scan list supports a mixture of analog and digital channels, you can add/delete a channel or set priority for the channel by editing the scanning list. The scanning modes support time scan, carrier scan and search scan. The current channel scan list add the scan group containing at least 2 channels to open the scan channel function. When scanning, listen to the channels in the scan list and check whether there have voice activities in each channel. There are three types of scanning: non- priority , 1st priority, and 2nd priority selectable. the LED indicator light flash orange. When scanning is active to a certain channel will stop to receive. IF receive an unnecessary call, press the programmable key noise channel to temporarily delete and it can temporarily removed from the current channel in the scanning list. If want to close scan, can long-press keypad programmable key quickly enter scan off or enter the scan menu to select scan off, switch the channel or press the programmable key scan on/off to exit the current scan. Note 1. If the channel checks the automatic scanning function, when switched to this channel, the device automatically enter the scan. When the programmable key function is set to scan turn on/off, it can be opened scan directly by programmable key.

Digital Emergency

Alarm Emergency mode is used to express an emergency situation.You can launch emergency alarm at any time in any screen to enter emergency mode. This radio supports three alarm types, three kinds of emergency alarm. Emergency Types: Routine: When the radio launch the emergency alarm, the screen displays emergency mode and the alann tone are continuously played Silence: When launch an emergency alann, there is no prompt on the screen and n alann bell is played, ii is not allowed to match the reception are played. Silence with Voice: When the radio launch the emergency alarm, there is no prompton the screen and no alarm bell is played, but allow any voices calls that match the reception are played.

Emergency Modes:
Emergency Alann: The radio launch the emergency alann, when receive the confirmation or trail times then will exit the “emergency” mode Emergency Alann and Calls: Once press “emergency alarm” key, it will sen an emergency alann, then can press PTT key to launch emergency call Emergency Alann and Voice: Once press the “emergency alarm” key, ii will sent the emergency along, then the voice can be sent automatically.

Sent Emergency Alann
The current channel adds an emergency system and reply channel set as the channel. Then can sent emergency information at the current channel. Press the set emergency mode to tum on function key, LED indicator light flash red, the uppe screen displays “emergency alann• and alann group calls contact and group calls.

Exit Emergency Alarm
In nonnal+emergency alann mode, when the number of attempts to send an alarm arrives or press the set emergency mode tum on function key, exit the alann. Or press PTT key will automatically alann mode,. In the unconventional alann mode, press the set emergency mode tum on function key to exit alann mode.

Receive Emergency Alarm
If activated, your radio will automatically confinn emergency alann. When radio receive the emergency alann, the interface will display emergency alann, the ID orname of the alann initiator, and continuously played the prompt. Otherwise there is no hint. Exit emergency alann, press emergency alann tum on function key.

DTMF

• Analog Channel, DTMF function allow radio system with interference to operate radioin the radio system.
• Initiating: Under analog mode, press the programming key to start the DTMF cal (programmable key should preset one touch key to connect DTMF calling ID number then can be used). Mer confines the hint played, then press PTT to talk.
• Receiving: Programmable software set the receive signal of the current channel is
  DTMF, when the decode number is DTMF personal ID number, decode succeed and played bells, and can communicate with the other in the reset time. When the reset time comes, it needs to decode again. The decoded number as kill code or waken code and the machine will be killed or awakened

PTT ID

Initiating: Under analog mode, ii can set the line code and down line code of DTMF by programmable software, analog channel enable line and down line code, each time press PTT send line code, release PTT sent down line code.

Encryption

You can use digital or analog way to initiate or remote kill in the radio system. For example, you may want to stop using a stolen radio to prevent thieves from using it and enable ii when recovering. Note:The execution or activation of the radio is limited to open(set up on programmable software) the function of radio.

Lone Worker

Work alone can suitable to the individual working in an unexpected situation during work, and can’t make keystrokes or voice launch in the preset time, and the radio can automatically enter alann to get help. By checking the “work alone” option from programmable software digital mode channel, the overall settings set up a work alone response time and reminder time. The response can be selected as keystroke operation and voice launch. Note:

•  Only support digital mode channel.
•  When an emergency system is not selected, this function is disabled.

Battery Level Press the pr-programmable key can view the remaining battery voltage, so that users can understand battery usage and charge the battery timely. The main interface battery displays (iii) three grids is sufficient of electricity, two grids is moderate, one grid shows the battery is low, if the icon turn m and there is a low electric hint that the battery is in sufficient, it should be recharged as soon as possible.

Troubleshooting

Battery may not be properly

replace new battery.
Can not talk to other members of your group| Verify transmitting is within effective operating range. Verify chanbnel, frequency and code setting are correct.
Hearing other conversation on a channel (not group members’)| Please change code settings, including all two way radio settings of your group.

Warranty Card

Terms and Conditions

•  This warranty is provided only for product purchased from the authorized dealer of hereinafter called .
•  Warrants this product to be free from manufacture’s defects for a specified period.
•  Within the specified warranty period, will repair or replace non consumable parts (excluding casing, accessories, batteries, cable and consumable) that are damaged under normal use (by judge of) at no additional charge.
• The warranty will not be covered under the following conditions
  •  Out of warranty products.
  •  The product is modified without approval.
  •  Obvious attack of appearance whatever it is.
  •  The product is subjected to unusual physical or electrical stress,including physical damage, burnt components and broken connectors, and watered radio.
  •  The serial number label is removed or altered
• This warranty card must be presented together with dealer’s invoice when the defective product is returned for repair.Otherwise, reserve the right of not providing free warranty during the warranty period.
•  The customer is responsible for returning the defective product at his own expense.
•  Your warranty period is calculated from the date of invoice of this product.

The FCC warning

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

•  This device may not cause harmful interference.
•  This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radiofrequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verificationof harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

Our radio generators RF electromagnetic energy during transmit mode.This radio is designed for and classified as “Occupational Use Only”,meaning it must be used only during the course of employment by individuals aware of the hazards,and the ways To Minimize Such hazards. This radio is NOT intended for use by the”General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for”Occupational Use Only”. addition, our radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:

• IEEE Std. 1528:2013 and KDB447498, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
• American National Standards Institute (C95.3-1992), IEEE

Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields-RF and Microwave. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio

Electromagnetic Interference/Compatibility
During transmissions, The radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft,and blasting sites.

Occupational/Controlled Use

The radio transmitter is used in situations in which persons are exposed as a consequence of their employment provided  those persons are fully aware of the potential for exposure and can exercise control over their exposure. This radio complies with IEEE and ICNIRP exposure limits for General Population/Uncontrolled Environments RF exposure environment at operating duty factors of up to 50% and is authorized by the FCC for General Population use only. An appropriate warning lable is affixed to all units. In order to comply with RF exposure requirements, a minimum distance of 2.5 cm must be maintained when held-to-face and bodyworn operations are restricted to the approved original acessories (belt clip), a minimum distance of O cm. Do not use this device when antenna shows obvious damages.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>