Kmart Telescope Instruction Manual
- June 5, 2024
- Kmart
Table of Contents
Telescope
Instruction Manual
TELESCOPE ASSEMBLY INSTRUCTIONS
PARTS INCLUDED
-
REMOVE THE TRIPOD FROM THE BOX AND EXTEND THE LEGS BY UNLATCHING THE LOCKS AND PULLING EACH OF THE LEGS OUT TO FULL EXTENSION.
-
LOCK THE LATCHES BACK IN PUCE TO SECURE THE LEGS, THEN SPREAD APART THE TRPOD ON A FIAT AND STABLE SURFACE.
-
ATTACH THE MAIN BODY OF THE TELESCOPE AND ATTACH IT TO THE TOP OF THE MAIN BODY CONNECTING SCREW, ALIGNING THE THREAD HOLE WITH THE SCREW.
-
TIGHTEN THE KNOB ON THE UNDERSIDE OF THE ATTACHING BRACKET
-
UNSCREW AND REMOVE THE TWO BOLTS ON THE TOP OF THE TELESCOPE
-
PLACE THE FINDER SCOPE AND BRACKET OVER THE SCREWS. MAKE SURE THE FINDER SCOPE BRACKET FITS OVER THE TWO SCREWS ON THE TELESCOPE SECURELY, THEN TIGHTEN. THE FINDER SCOPE SHOULD BE FACING THE FORWARD DIRECTION AS SHOWN IN THE IMAGE.
-
INSTALL ONE OF THE TWO LENSES INCLUDED (6MM AND 12MM) INTO THE FOCUS TUBE AND SECURE IT BY TIGHTENING THE SCREW. MAKE SURE NOT TO OVER-TIGHTEN IT. FOR EASY VIEWING, YOU CAN FIRST INSTALL THE DIAGONAL PERISCOPE VIEWER INTO THE FOCUS TUBE. THEN INSERT ONE OF THE LENSES INTO THE DIAGONAL PERISCOPE VIEWER AND TIGHTEN IT. MAKE SURE THE END OF THE DIAGONAL PERISCOPE VIEWER IS INSERTED INTO THE FOCUS TUBE OF THE TELESCOPE WITHOUT THE SCREW.
TECHNICAL SPECIFICATIONS
Objective Focal Length 600MM
Field of View| 1 Degree
6MM Eye Piece| 100x Magnification
12MM Eye Piece| 50x Magnification
USING YOUR TELESCOPE
Make sure the tripod is placed on a flat and stable surface.
Use the Finder Scope first to acquire the target object, then use the Focus
Knob to obtain a clear image.
Apply small and slow adjustments to focusing
MAINTENANCE
This telescope is a precision instrument and should be carefully stored in a cool and dry environment. Do not store near direct sunlight. Both eye-piece lenses must be stored in the supplied plastic containers when not in use. It is recommended to clean the glass lens after every use with lens paper to prevent damage or scratches.
CAUTION: DO NOT VIEW THE SUN DIRECTLY WITH THIS TELESCOPE AS IT CAN CAUSE SERIOUS EYE DAMAGE. DO NOT POINT THE TELESCOPE AT OR NEAR THE SUN. DO NOT LOOK THROUGH THE TELESCOPE AS IT IS MOVING. ADULT SUPERVISION IS RECOMMENDED.
Adult assembly required.
For Ages 8 years+
OPERATING INSTRUCTIONS
This telescope uses glass optics for great clarity and is housed inside an
adjustable body. It is designed for easy operation and to provide sharp and
clear viewing of distant objects. 
ATTENTION: The power stated is for reference only and there may be a difference in magnification
Technical Specifications:
Objective Focal Length 600mm
Field of View:1 degree
Finder Scope Magnification
Eye-Piece Magnifications: F=6mm for up to 50x magnification and F=12mm for up
to 50x magnification
Maintenance
This telescope is a precision instrument and should be carefully stored in a
cool and dry environment. Do not store near direct sunlight. Both eye-piece
lenses must be stored in the supplied plastic containers when not in use. It
is recommended to clean the glass lens after every use with lens paper to
prevent damage or scratches.
Installation:
Remove the tripod from the box and extend the legs by unlatching the lock and
pulling each of the legs out to full extension. Lock the latch back in place
to secure the legs, then spread apart the tripod on a flat and stable surface.
Take the main body of the telescope and attach it to the top of the Main Body
Connecting Screw, aligning the threaded hole with the screw. Tighten the konb
on the underside of the attaching bracket. Then, unscrew and remove the two
bolts on the top of the telescope. Place the Finder Scope facing the forward
direction as shown above.
Install one of the two lenses included (F=6mm and F=12mm) into the focus tube
and secure it by tightening the screw. Make sure not to over-tighten it. For
easy viewing, you can first install the Diagonal Periscope Viewer into the
Focus Tube. Then insert one of the lense into Diagonal Periscope Viewer and
tighten it. Make sure the end on the Diagonal Periscope Viewer without the
screw is inserted into the focus tube of the telescope.
Using Your Telescope:
Make sure the tripod is placed on a flat and stable surface. Apply small and
slow adjustments for focusing. Use the Finder Scope first to acquire the
target object, then use the Focus Knob to obtain a clear image.
KEEP THIS INSERT FOR REFERENCE SINCE IT CONTAINS IMPORTANT INFORMATION.
ADULT ASSEMBLY REQUIRED. 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>