Einhell GE-WW 5537 E Home Waterworks Instruction Manual

Einhell GE-WW 5537 E Home Waterworks

Caution – Read the operating instructions to reduce the risk of inquiry

Important!
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Safety regulations

Caution!
Read all safety regulations and instructions. Any errors made in following the safety regulations and instructions may result in an electric shock, fi re, and/or serious injury.
Keep all safety regulations and instructions in a safe place for future use.
Caution!
In stagnant water bodies, garden ponds, swimming ponds, and their surrounding areas the unit may only be used with an earth leakage circuit breaker with an actuating rated current of up to 30 mA (according to VDE 0100 Part 702 and 738). The equipment is not designed for use in swimming pools and paddling pools of any kind or other bodies of water in which people or animals may be present during operation. It is prohibited to operate the equipment if a person or animal is in a dangerous area. Ask your electrician! This equipment is not designed to be used by people (including children) with limited physical, sensory or mental capacities or those with no experience and/or knowledge unless they are supervised by a person who is responsible for their safety or they have received instructions from such a person in how to use the equipment safely. Children must always be supervised in order to ensure that they do not play with the equipment.

Important!

• Always inspect the equipment visually before using it. Do not use the equipment if safety devices are damaged or worn. Never disable safety devices.
• Use the equipment only for the purposes indicated in these operating instructions.
• You are responsible for safety in the work area.
• If the cable or plug is damaged by external influences, the cable may not be repaired. The cable must be replaced by a new one. This work may only be carried out by a trained electrician.
• The voltage of 230 V alternating voltage specified on the rating plate must be the same as the mains voltage.
• Never use the power cable to lift, transport or secure the equipment.
• Ensure that the electrical plug connections are in areas that are not at risk of flooding or protect them from moisture.
• Pull the mains plug before starting any work on the equipment.
• Do not expose the equipment to a direct jet of water.
• The operator is responsible for complying with local safety and installation regulations. (Ask an electrician if you are in any doubt.)
• Consequential damage caused by flooded rooms in the event of the equipment suffering faults must be prevented by the user by means of suitable measures (for example installing alarm systems or a reserve pump, etc.).
• In the event of a failure, repair work may only be carried out by an electrician or by ISC after-sales service personnel.
• The equipment must never run dry or be used when the intake line is closed fully. The manufacturer’s warranty does not cover damage caused to the equipment as a result of running it dry.
• The pump must not be used to operate swimming pools.
• The equipment must not be installed in the drinking water pipeline.

Layout and items supplied

Layout (Fig. 1-2)

1. Pressure connector
2. Carry handle
3. Power switch
4. Pressure gauge
5. Water drain screw
6. Suction connector
7. Coarse fi lter screw
8. Ventilation screw
9. Coarse fi lter
10. Non-return valve
11. Wrench for coarse fi lter screw

Items supplied
Please check that the article is complete as spe-cifi ed in the scope of delivery. If parts are missing, please contact our service center or the nearest branch of the DIY store where you made your purchase at the latest within 5 work days after purchasing the article and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the warranty provisions at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Important!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

• Domestic Waterworks
• Wrench for coarse filter screw
• Original operating instructions

Proper use

Applications

• Irrigation and watering of green areas, vege-table beds and gardens.
• Operation of lawn sprinklers.
• For drawing water from ponds, streams, rain-water butts, rainwater cisterns and springs
• For supplying service water

Transport media:

• For the pumping of clear water (fresh water), rainwater or light suds/service water.
• The maximum temperature of the fluid must not exceed +35°C if the equipment is opera-ted permanently.
• Do not use the equipment to pump inflamma-ble, gassing or explosive fluids.
• The pumping of aggressive liquids (acids, al-kalis, silo seepage etc.), as well as liquids with abrasive substances (sand), must likewise be avoided.
• This equipment is not designed to convey drinking water.

The equipment is to be used only for its prescri-bed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or inju-ries of any kind caused as a result of this. Please note that our equipment has not been de-signed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Technical data

• Mains connection ………………………230V ~ 50 Hz
• Power rating ………………………………………. 590 W
• Pumping rate without non-return valve: ….3750 l/h
• Pumping rate with non-return valve: ……3450 l/h
• Max. delivery head ……………………………….. 38 m
• Max. delivery pressure …………0.38 MPa (3.8 bar)
• Max. suction height ………………………………… 8 m
• Pressure and suction connector .33.3 mm (R1IG)
• Max. water temperature ……………………….. 35 °C
• Tank capacity ………………………………………….20 l
• Cut-in pressure approx. ……….0.15 MPa (1.5 bar)
• Cut-out pressure approx. ……..0.30 MPa (3.0 bar)

Before starting the equipment

Connecting the intake line

• The intake hose or pipe should have a mini-mum diameter of 25 mm (1”); a diameter of 32 mm (11/4”) is recommended for suction heights exceeding 5 m.
• Connect the intake valve (foot valve) with in-take cage to the intake line.
• Position the intake line so that it rises from the water withdrawal point to the equipment. Avoid positioning the suction pipe higher than the pump, as this would delay the escape of air bubbles from the suction pipe and impede the priming process.
• Install the intake and discharge lines in such a way that they do not exert any mechanical pressure on the equipment.
• The intake valve should be low enough in the water to ensure that if the water level falls, the equipment will not run dry.
• A leaking intake line will draw in air and there-fore not draw in any water.

Connecting the discharge line

• The discharge line (min. 19 mm (3/4”)) must be connected to the 33.3 mm (R1IG) female thread discharge line connector of the equip-ment either directly or with the aid of a threa-ded nipple.
• With the right couplings it is also possible, of course, to use a 13 mm (1/2“) delivery hose. The smaller delivery hose results in a lower delivery rate.
• During the priming operation, fully open any shut-off mechanisms (spray nozzles, valves, etc.) in the pressure line so that the air can escape without obstruction.

Electrical connections

• Connect the appliance to a 230 V ~ 50 Hz socket-outlet with earthing contact. Minimum fuse 10 ampere.
• A built-in thermostat protects the motor from overloading and blocking. The pump is swit-ched off automatically by the thermostat if overheating occurs and is switched on again automatically after cooling.

Operation

• Install the equipment on a solid and level surface.
• Remove the ventilation screw (8).
• Unscrew the coarse filter screw (7) using the supplied wrench (11) and remove the coarse filter (9) together with the non-return valve (10) as shown in Figure 2. Now you can fill the pump housing with water via the coarse filter screw (7). Filling the intake line accelerates the intake process.
• Assemble in reverse order.
• Open the discharge line.
• Connect the mains cable.
• Switch on the equipment with the power switch (3) – water can be suctioned in for up to 5 minutes (maximum suction height).
• The equipment will shut down when the cut-out pressure of 3 bar is reached.
• After a loss of pressure due to water consumption the equipment will cut in again automatically (cut-in pressure approx. 1.5 bar). After finishing the work, switch off the equip-ment with the power switch (3).

Replacing the power cable

If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.

Cleaning, maintenance and ordering of spare parts

The equipment is almost completely maintenance-free. In order to ensure a long service life, however, we recommend that you regularly check and care for the product.
Important!
The equipment must be disconnected from the power supply (pull the power plug) prior to performing any maintenance.
Servicing
If the equipment becomes clogged, connect the discharge line to the water line and disconnect the suction hose. Open the water line. Switch on the equipment several times for approx. two seconds. This should resolve the majority of clog-related problems. Inside the pressure, the tank is an expandable water sack and an air compartment whose maximum pressure should lie at approx. 1.3 bar. Pumping water into the water sack causes the sack to expand so that the pressure in the air compartment rises to switch-off level. If the air pressure is too low, you should raise it. To do so, unscrew theV plastic lid from the tank and top up the pressure to the correct level using a tire pump with a meter at the valve. Important: Be sure to completely empty the water bag fi rst using the water drain screw
(5).
Replacing the mains cable:
Important: Disconnect the equipment from the power supply! A defective mains cable may only be replaced by a qualified electrician. There are no parts inside the equipment which require additional maintenance.
Cleaning the coarse filter insert

• Clean the coarse filter insert at regular intervals, and replace it if necessary.
• Remove the coarse filter screw (7) and coarse filter (9) together with the non-return valve (10) (Figure 2).
• Disassemble the coarse filter insert as shown in figure 3.
• Do not use abrasive cleaning agents or petrol to clean the coarse filter and the non-return valve.
• Clean the coarse filter and the non-return val-ve by tapping them on a flat surface. In cases of stubborn dirt, first clean with soapy water, then rinse with clear water and air-dry.
• Assemble in reverse order.

Storage

• If the pump is not going to be used for a long time or has to be removed for the winter months, rinse it out with water, empty it com-pletely and allow it to dry.
• The equipment must be completely drained before it is subjected to frost.
• After long stoppages, make sure the rotor turns correctly by briefly switching the pump on and off.

Ordering replacement parts:
Please quote the following data when ordering replacement parts:

• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required For our latest prices and information please go to www.isc-gmbh.info

Disposal and recycling

The equipment is supplied in packaging to pre-vent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.

Troubleshooting guide

–   Pump rotor blocked -thermostat switched off

| –   Check voltage

–   Dismantle and clean pump

No intake| –   Non-return valve dirty

–   Pump chamber without water con- nection

–   Air in intake line air-tight

–   Max. suction height exceeded

| –   clean

–   Fill water into intake

–   Make sure intake line is close

–   Check suction height

Inadequate delivery rate| –   Suction height too high

–   Coarse filter dirty

–   Water level falling rapidly

–   Pump performance diminishedby contaminants part

| –   Check suction height

–   clean

–   Place the suction hose at a deeper level

–   Clean pump and replace wearing

Thermostat swit- ches pump off| – Motor overloaded – friction caused by foreign substances too high| – Dismantle and clean pump. Prevent intake of foreign substances (filter)

For EU countries only
Never place any electric power tools in your household refuse. To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot. Recycling alternative to the return request: As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment. The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products, is permitted only with the express consent of the ESC GmbH. Subject to technical changes

Warranty certificate

Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee conditions regulate additional guarantee services. Your statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.
2. Our guarantee only covers defects suffered by the device which has been verifi ably caused by a material or manufacturing fault and is limited to the rectifi cation of such defects or the replacement of the device at our discretion. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
   • Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.
   • Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
   • Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if on-site service is used.
5. Please report the defective device to the following internet address to register your guarantee claim: www.isc-gmbh.info. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement device.

Of course, we are also happy off er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address. Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.

Warranty provisions
ESC GmbH or the DIY store where you made your purchase guarantees the repair of defects or replacement of the equipment in accordance with the overview below. Statutory guarantee claims are unaffected.

purchase / date on the bill)
Missing parts| | 5 work days

Not necessarily included in the scope of delivery!
For consumables, wear parts and missing parts iSC GmbH guarantees the correction of defects or a new delivery only if the defect is reported within 24 hours (consumables), 5 work days (missing parts) or 6 months (wear parts) after purchase and the purchase date is verifi ed with the bill. In case of defects concerning the material or construction, we kindly request you to submit the equipment together with the fully completed warranty card supplied with the equipment. It is important that you enter an exact description of the defect

To do so, answer the following questions:

• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?
  Describe this malfunction.

References

• iSC Onlineshop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>